Video

Talked way way too slow! Frustrating!!!!

Spray with W40 first before removing pads with hair dryer....I believe W40 is non-flammable.

Thanks

I have one, and it's a lousy flashlight.

A bunch of haté haté smh

5 Cent Fix I have a lot of these and I just put a nickel or two on top of the last battery I put in. Improves a lot but not perfect.

Next time leave the stump waist high and pull higher up. The extra height does wonders for leverage to pull it out of the ground.

Too much wood lifting and handling. Stand all the logs up in a big circle. Wrap the whole circle in a ratchet strap or 2 and cinch up tight. Swing away until they are all split.

I was irritated with my light and found this. It works. I added a little more painters tape than you did and it’s flawless. Thank you!

To fix the battery wobble, I simply use a piece of printer paper, rolled and cut evenly to the length/depth of the tube. You might need to overlap the sheet to get proper fit, allowing batt to slide slowly when inserting/removing.

I ha e The same Model, works great

Thanks ...

only 1 cut...need to see more cuts thanks

Hey rookie how about ripping a 2x6 Doug for and see how motor handles it.

easier fix.....take it back to Costco

Nice fix idea but maybe an Easier and better way to fix is to gently stretch the spring on both ends... Be careful not to pull from circuit on LED end (This way does require disassembly which isn't to bad if your mechanically inclined.). It is soldered to board and if pulled to hard will come off. It isn't easy to get back on unless you have a pretty good soldering station setup.. Plus you risk heating up other components on circuit board or cause cold solder joints. Also be careful to not let batteries slam down onto LED end of spring when you refill batteries either. Gently let them slide into the flashlight by tilting it until they slowly land in place. I also bought 5000mA "C" cell rechargeable batteries thinking it would save buying batteries every 10 hours of use. Bad Idea fried one of my lights in just a second of use. Don't recall any warning not to use in instructions. Maybe I missed it. Should be engraved on end where you put batteries in. So you don't destroy a nice LED light. The duracell flashlights before these from Costco did the same thing not compatible with rechargeable batteries fried one of those too didn't say a thing about Rechargeables in instructions. Suspect it's a DURACELL thing so they can make sure they sell billions and billions of batteries that will make them Billions of $$$ and end up in our landfills. SAD....

how do you take a spark to switch soda to fix a switch

it doesn't except Dado blades, this is a toy not a real table saw. y buy a table saw if u can't use dados, just use worm drive

The only different is only by 5Amps compare to the blue 10'' 0ne all else is the same will start working my new one tomorrow.

I just bought this POS. It gets stuck every time I push something through. It is unlocked to allow the substrate through but I still have to push it with the stick to move it away from the guard. That makes it pretty unsafe. Its going back.

Loud!

I have this exact same table saw and mine just started to kick and twist the whole thing a little when I turn it on. I didn't see you have that problem yet? Also, can you make a 45 degree bevel rip cut on a long board a 2 by 4 would be fine. Thanks!

Hi does shimless dado by freud fit that?

Beautifully made video! Makes one, like myself, wonder what you might be able to do with a go pro or something of the sort! Ride on.

Only a 4 Runner...

Nice…..what trail is this in Rancho?

The simplest ideas are best! Why didn't I think of this? This will make my hydraulic log splitter redundant. Thank you.

wierd ass song

Great song choice!

I signed up for the free trial of Sony Vegas Movie Maker HD 11.0 and used that to edit this video. I think it is a 15 day trial. Program costs $50 if you want to buy it after that. To me this program was a bit tricky and time consuming to figure out and use but I do not have much experience with other programs to compare.

what program do u use to edit the video?

Nice job! Looks like a lot of fun!

If you split firewood by hand TRY THIS!!!!!! it works great, I got the idea from another video(sorry) but I will never split firewood without a tire again. Honestly Its the way to go

Must be very "tiring" work.

sweet footage man! all you guys look like your having a great time. tons of awesome airs too.... oh, and nice carving at 3:03!

im liking it...... you should start selling these :D ... pretty pro idea ^_^

Thanks for the cool idea. Getting ready to split some wood and found an old tire recently. Hope the tire is still there.

Pretty slick. Simple but elegant.

that is awesome

Sorry. It was just a test video for my new camera and a try at first youtube video.

i want my 4 seconds back!