Video

Bob your always working on something,is there anything you can't fix,lol!

Lol

Not bad😮

Looks like replacing a new one would be the quickest thing

No reason to dry fit Pex, Put it together and crimp it immediately so you don't forget rings and hate yourself. Its faster to just cut out any mistakes.

Skinwalker caught irl 💀

Why did you cut the studs all open. Support

You and him: who ever moves first is gay Bae you got somthing in your noseeeeeeee!:

Nice work.

Everything was PEX B with the stainless steel crimp ring.

What are those connections on the supply valves?

I think I'll name him "Buster"

Oh, look: the newest member of NCOTB (New Cats On The Block)!

I dont care what the manufacture, store sellers, or workers say about quick connect fittings! I refuse using them anywhere other than my basement. Even then, I only used 2 of them where I was in a crawl space and had no room to sweat on a guaranteed-will-never-leak fitting. I inherited my grandparents house that was built in the 1950's and NOT 1 single sweat-on fitting ever leaked

You couldnt get the cap fitting off because of the water you said dripped out. the water was keeping it from getting it hot enough. I didnt see any water when you did get it off, maybe it boiled away. You could of cleaned the solder from the pipe by heating it up to the point of melting and simple wiped it off with a dry rag. But you got the job. Thats all that matters

You melt the solder, then wipe it off with anything, even a dry paper towel. Emery cloth is a possibility. Sanding screen too. Strongly discourage pushing on that line like you were. You don't know what you are pushing against on the other side. Guys have kinked and pierced lines doing that. Or they mess up hangers causing the line to start slapping the structure when turned on or off.

take the nut off of the pipe valve so the water drains out of the pipe!!!!!!!!!!!!!!!!!!!!

"just refining my technique" I tell myself that before any drywall repair. Soder boobs are sand papers problem a good 180 grit will knock it down quick. Keep at it!

That steam needs to get to the same temp that the solder melts at... I was expecting this to be a video of how a pipe explodes. The pressure of the steam should be considerable, even if it's not near enough to split open the copper. Next time drain your pipes and add ports for draining and air intake.

Have at it Bob!

Yeah, make a video while water continues to run down the wall, schmuck

We are three of the best plumbers that ever plumbed a plum

Uhh... at 2:20, you've got to address that 'plumping'. That green patina is corrosion probably from flux that wasn't cleaned off when it was soldered and i looks like you've got pinhole leaks already. I'm not sure WTF that duct tape is doing there. Those foam insulation sleeves are pretty useless and it looks like they are on both hot and cold lines. I'm not sure what's going on with those bends. The vertical tube in the center looks like it was forced into he elbow going left into a 3 inch piece into the tee. None of that looks well fitted. I'd cut all that out and redo it as most of those solder joints look like they were not cleaned and fluxed properly. If you seal and foam that in, I guarantee your going to have leaks. Whoever did that 'work' needs to step back and learn how to properly solder copper tubing. I mean no offence if it was you, but if that was a purported plumber, well . . . Anyway, that mess is going to cause issues in the (near) future. I'd hate to see you go to all the trouble of sealing everything up only to end up with bigger problems

You keep finding more to do. Good job

well well ! the tube is gone,You have really put some challenging work in on this project. When you decided to remodel you went all the way, Don't over do it

Man you been busy. Good luck on getting that tub out.

Looks like a LOT of demanding work

Hey bob just checking in!! Your always working on something,your quite the handyman!! Take care!!

Cool little guy just jompin away.........

Hell ya bob

3060 is cool and all but when are you getting a gt 1030

my first graphics card exactly! its great.

Those look exceptional

Tree rats.

Wow. The power of mother nature is so incredible. Cool

To fat to jump

1 million thumbs up

Just checking in my friend,ill have my wife watch this she's always burning something,lol!! Take care hope all is well!!

I love them

I finally figured out why my feeder got empty every day. Damn squirrels

I dig your vibes man. You put out good energy my friend. ✌️😸

I don't like flat screen TV's. They remind me too much of the tv walls in Fahrenheit 451.

That’s awesome. 👍🏻

Tell us what it is Bob!

what is that?

Wouldn't a rubber ring of some sort work well for that hole?

Just put a switch in like that,no kidding!! It seems at least with the plastic rocker switch type they break after a few years of hard use,!!! Thanks my friend just checking in to see what's up!!!

Way to go, looks great😁

I like your idea but i would not stagger it. Just my 2 cents

❤❤❤ok😊😊😊