Video

What was the problem stuck in first gear mine is stuck

My transmission is stuck in gear could the forks be broken

So how would I know if I have a stroker motor is there a way

I believe that is a transmission mount bracket

Glad everything worked out for you. Stay humble and thankful.

Where you located man

2ba4 work good too.

When I tighten my comp nut to spec I can't get it to roll over.

Great tip on marking with a sharpie when you can’t see the woodruff key. Genius! 👍

Great tips and tricks. “Sometimes it’s better to back off and take a breath. Wisdom! 👍Nice camera work and editing too.

Great explanation as you progressed. 👍👍

Looking for brake lines on my 82 FLT. Three piece front lines 2 section rear lines. Any advice.??

Ever pull the clam shell apart to change the rear sprocket. My mind seized up . I had to buy the manual and parts manual. Still not 💯 I did it right

where can i buy these vintage w/w tires ?

where would i find tires for this servi car i need 3

I need a heel toe shifter and the bracket for a 1972 FLH. You have?

Cool😂

Great build! Thanks for sharing.

Hi. I have a 1983 FX Wide Glide. Regards from Norway

no garage mechanic would not have a clutch hub puller you are a hack you aint no serious biker with that bullshit please do not touch anymore shovelheads get yourself a honda

Just checking in on you my brother hope everything is going ok 🙏

Hi I’m also working on the same bike replacing trans main shaft seal trans runs fine the only problem I have is that when I go to first the lever will not return without help but the rest of the gears return back fine any help would be appreciated thanks

Sounds great! We are looking for the path of the Speedo cable, any chance you’d share? 😊

Ethyl!

It’s gorgeous! Any chance you could show the track of the speedo cable? 😊

Good afternoon. Do any of you guys know where I can get my hands on one of those final drive skateboard wheel chain tensioners? Thanks for your help.

Like to of had the knucklehead frame

Rear chain oil bath cover setup ? $$ ?

Fun fun...just got finished fiddling with a draggy Barnett clutch...ended up taking the clutch basket off checking the key and re torqing the nut and cleaning the plates with brake clean, refilling with ATF-F instead...waiting on a rain free day to tester out.

Hei. I wonder if i can fit my 5 speed transmission from a 1981 flh, same as in video,, into a gearbox that fits my rigid bobberframe.and what is it called is my question ?hoping i dont need a complete new gear transmission . Using motor and all the parts i can re-use /build into my rigid shovel bobber project.springer fork i got also

I dig it.

Sweet 🏍️👍👍👍👍

😊 great vid..love parts ....

👍👍👍

What's going on have not seen any video from you in a month is everything ok post a video and let everyone know how you are doing take care my brother

I have 1948 servi car parts if you need something let me know am in wi

Beautiful sled. I'm also a Hobson who built his own 74 Honda CB750 with Amen Savior frame. Nice work and great channel.

I'm working in a 1980 FLH now. Kool bike ...

Awesome my Friend!!!

Keep an eye on that Invader! I had a 5-spoke set on an Ironhead, some years back. Heading home on the highway, my front tire went flat! That was an interesting ride, trying to get to the right shoulder, while the bike was pulling me left, all the while cars are zooming by! Not 10 minutes later, some guy in a pickup truck, pulled over, loaded me up and got me home. On closer inspection, I discovered one of the spokes at the weld, worked it's way off the rim and was slowly working it's way thru the inner tube! Invaders look good, but to this day, the sight of them makes me cringe....

Love your bike and what you’re doing, but the camera constantly jumping around makes it impossible to watch

Do you have are reverse gear?

Is it a good boy beginner bike if you rode dirt bike as a teenager?

Cool serve car

As a laced wheel guy I find those Invaders to be quite pretty, and the Springer looks sturdy (from here) and also quite attractive.

Wow; Mr Hobson you have that beautiful bike shining like a very rare Diamond unbelievably great work thank you for all of your hard work...Willis from Aztec NM...⚡⚡⚡🌟🌟🌟🔥🔥🔥

Great work 👍⚡🏁🇱🇷

I need a low mileage Speedo for my 91 Electra glide

Wow everything is coming together the lathe has come in handy for what you are doing very awesome keep up the great work my brother stay safe be blessed

Sorry, but the fitment of the rear fender & bitch bar looks like @$!