Video

Can you show us a video on how to put a new dirt bike tire on to pump up the tube

I have a 94 yz125 that I brought in pulled apart... I can't find the ground wire, it's not on the CDI, magnetto, or wire loom, does the 94 not have one?

My distance collar had a slight bur and I grinder like half a miler meter off to make it smoother is that ok?

Always measure stator coils without flywheel!!!! The flywheel effects the measurements of the source coil 1

Can they leak if u dont bleed if the bike has being moved in a car just a question have a pitbike with one leaking and the other ok only started happening after i picked the bike up after a week i have rode the bike yet so im assuming there ok just need bleeding and the seal mate putting in the em its a kxf125 pitbike not sure on the fork oil weight what would he recommended for a pit bike

good video bud, but like others have said, don't hold the grinder like that, it will go right in your forearm

Where can i buy the main jet mount? I cant find it anywhere

Do you know anything about racing carburettors I have a racing carburettor on one is it any different

I see you wiped off the reeds very quickly. What do I spray them with to clean them? Is carb cleaner ok?

Yo dude, I tried to assemble the shift assembly and it was jammed up. Everything appeared to be normal, what should I look out for? I have it all apart again.

Website finally went down - thanks for all the help!

What size socket do I need to take off clutch after I flatten washer?

🎉

can you use a TMX38 carb for a 2000 yz125 even though its suppose to be a TMX36?

Question what would happen if the gasket for the jet block gose bad will it make the bike flood out ??

Did you remove the seperator cup before cleaning the master cylinder? The manual says remove, inspect and and repolace the o ring underneath iof necessary but it doesn't show how to remove it.

How dis you remove the bolt what did you use?

I just got my dirtbike and I ordered pro taper, grits diamond hopefully that works because my last grips whore the skin off my hand

I used this stuff back in the 80’s, smells soooo good and used to keep my 125’s alive👍

Thank you for this video bro,,i applied it and it works ❤❤❤ i thought my master cylinder is broken almost 2 days doin it and it doesn't work 😅

Keep the opposing nut side pinch bolts tight so when you unloosening the nut it holds it

thx

I have a problem when I pull the throtle fast its chokes Its not comfortable when I riding enduro pls help

what kind of grease are you packing the seals with?

Where to buy this in EU?

lol thanks. Finally dialed in my KDX

How do you re set the idle adjustment knob ? My cr want ideal IV had the bike for year and never had a proper IV clean carby and new plug and still want ideal. I did take the idle screw with the lock nut out when I was cleaning it and forgot how many turns can you please tell me how many ruffly in it should be

Well done video. thank you

awesome video

Very effective! Please keep going making cool videos

Hey John what the stock setting for the suspension

Thankfully, my wheelbearings aren’t shot onto another video Why is my brake caliber sticking?

I'd assume this is the same thing or close enough for minibikes. Hopefully this helps me out🔥🤙

1.5 to 2.5 turns out from fully seated.

This video sucks need to slow down

I highly recommend two RIM locks. I use Nitro Mousse Platinum and I had my rear tire come off the rim last Sunday on an FE350. We were getting after it over some really gnarly rocky stuff and I guess she just rolled off on a rock. I made it back because the mousse held together and the single beadlock gripped the tire to allow traction. I have just ordered more rim locks need her ready for this weekend ride.

What happens if the rear brakes pads won’t open? So that I can slide th me tire in.

Had to watch this after is scene a dirt bike tire removal fast as hell in furiosa, I knew I was thinking right.

Wish i knew this before doing 70s on new 190cc pitbike and crashing on road 😂😂😂

JWG vibes

Hi! My bike starts, goes ok on idle (maybe a lil too high) but when i give throttle the gas hangs for a bit and slowly goes down, I dont think i have it too lean. Anything i can do to fix??

Would the torque still be 20 for a 2005 cr 250r for the sprocket thanks

Thinking i might do the same, only think I might hide the switch 🤔

Hey man I know this videos old hope you’ll find this comment, I have a 2000 kx80 and the rear axle rod refuses to come out of the bike. I think it’s insanely rusted and caked up inside it’s stuck. I’ve got it abut halfway out with a nut wrench and a hammer and a shitload of wd40, you got any tips or is my last resort completely rebuilding the rear end.

Hi Is here anyone who wants a self adjusting carb for his bike in 2024? I my self still looking for self adjusting carb, I prefer carb instead efi. Have a good journey everyone .

Bro u fixxed my stupid gas gas 250 it was 4 stroking bad and bi mechanic was able to fix it had to to down from a 180 to 160 and main jet was a 50 and went to a 45 bc it kept fouling plugs also 1-2 gear would feel like hitting rev limiter thank you so much

Would this work for 92-96? I have a 93 i need to rebuild the shock

We often make the mistake of just assuming people know what something is and how it works. Brilliant video. And thanks for the "why" - if your tire is flat because the valve stem is ripped at the base ... you need a rim lock.

If there was fuel with synthetic oil in the gas tank, is it possible to add fuel with castor oil to the gas tank or should the old fuel be drained?

2002 cr250 brand new mikuni carburetor starte in on choke it revs wide open no matter choke on or off tried adjusting the air mixture to still Rev wide open anyone can help me fix this issue I'd appreciate it