![George's Workshop](/img/default-banner.jpg)
- 69
- 1 041 504
George's Workshop
United Kingdom
Registrace 26. 12. 2020
Part 2# SAMSUNG Washer Dryer/ Machine Error Code “ dE “ Program won’t start, door lock doesn’t lock
Hi guys 👋
In this video I wanted to demonstrate that, an error code not always will tell you where could you find the source of the error, as you’d suppose by code.
In this case instead of a door lock change, a new main PCB board required. Sometimes the repair is not economical…😡
Thanks for watching 👍
See you soon 👋
In this video I wanted to demonstrate that, an error code not always will tell you where could you find the source of the error, as you’d suppose by code.
In this case instead of a door lock change, a new main PCB board required. Sometimes the repair is not economical…😡
Thanks for watching 👍
See you soon 👋
zhlédnutí: 563
Video
SAMSUNG Washer Dryer/ Washing Machine Error Code “ dE “ Program won’t start, door lock doesn’t lock
zhlédnutí 102Před 6 měsíci
This video shows a simple issue, starting the program and dE error code appearing on the LCD display of a SAMSUNG washer dryer or washing machine. If you are interested what is really happening, check the part 2# Thanks for watching 👍
Beko heat pump tumble dryer’s door opens and stops program. Popping door in the middle of cycle.
zhlédnutí 396Před 6 měsíci
Hello my friend, Today I will show you something unusual. This is not a real fixing, but without it won’t work your dryer properly. So, the dryer starts normally and after a while door pops and program stops. If you close the door and starts it will run again, but after few minutes door will open by itself. And you can repeat this method forever if you don’t clean the bottom filter. This issue ...
Hotpoint Aquarius Washer Dryer / Washing Machine find leaks, puddle under machine, leak detection…
zhlédnutí 543Před 9 měsíci
Hi, In this video I’d give a useful tip to save yourself from expensive repair costs and many inconvenience. Watch the video and keep in your mind my advice. See you next time 👋 Music: Miami Musician: Deleted Account Site: icons8.com/music/
How to fix BUSH tumble dryer if not heating. How to reset the sensor on BUSH / LOGIC tumble dryer.
zhlédnutí 4,9KPřed 9 měsíci
Hello guys, I brought an easy trick today, what you can use if your Bush/ Logic tumble dryer doesn’t heat up. I hope this will help for many people.
HOOVER Condenser Tumble Dryer buttons are irresponsive and “Loc” word appeared on display Child lock
zhlédnutí 4,5KPřed 9 měsíci
Hello guys, Don’t panic if your dryer’s buttons are irresponsive and Loc word appeared on the display unit. It is in the user manual, but many people has no clue what to do. In this video I will show how to remove the child lock. I hope you found useful my video 😉 See you shortly 👋
SAMSUNG eco bubble Washing Machine door can’t close easily. How to fix a loosened door?(Beko, Bosch)
zhlédnutí 271Před 10 měsíci
Hello, Probably you have experienced , your washing machine’s door is loosened and hard to close/ lock. I will show in this short video how easy to fox and only a screwdriver needed. Come with me and fix it yours together step by step. See you soon 😉
How to fix your Washing Machine, if tripping the fuse board? (Beko, Hotpoint, Indesit, Bosch, etc.)
zhlédnutí 5KPřed 10 měsíci
Come with me in this video and you can see one possible issue if your washing machine is tripping the fuse board. And the way how to fix it. I hope you will find useful my video and you are enough brave to fix it by yourself . Please press a like and subscribe. Thank you 😊 See you shortly 👋
BOSCH Washing Machines / Washer Dryer leakage/ water patch on floor from hidden place
zhlédnutí 171Před 11 měsíci
Please follow the manufacturer’s instructions and use the drum stabiliser screws during transport. The concrete counterweight’s free movements could cause expensive repair as would damage parts around them. Thanks for watching 😊 See you soon 👋
Drive Strider#1 Mobility Scooter ripped/ teared Handlebar Foam cover replacement
zhlédnutí 219Před 11 měsíci
In this video I will show you a little secret how to make easier a foam handlebar replacement. Follow my step by step instructions and it won’t take too long. Thanks for watching 😉
BEKO Washing Machines or Washer/Dryer shaking, vibrating and loud spinning cycle. How can you fix it
zhlédnutí 4,4KPřed 11 měsíci
Hi Guys, In the first part I’ve shown this shaking/ vibrating issue. And now I want to show how to investigate and fix it. This is only one possible issue and solution, but there could be something else, too. Thanks for watching and see you shortly.
Error codes: BOSCH E18, Beko E4 / E8, Zanussi E11, Hoover E02, Samsung 4C / 4E, Hotpoint F09
zhlédnutí 507Před rokem
Welcome on George’s Workshop channel. In this video I will show a trifle issue, that could be made during installation and result in many errors.
BEKO Washing Machine or Washer / Dryer shaking, vibrating, dancing and loud during spinning cycle 🫨
zhlédnutí 583Před rokem
Hi Guys, In this video I’ll demonstrate an issue that can occur on washing machines or washer/ dryers. May it’s happened with yours? If you’re interested what causes the problem and how to fix it at home, subscribe to my channel. In the second part I will show the solution. Thanks for watching and see you shortly.
Part 2# ZANUSSI Washing machine E40 error message, door lock replacement, how can be fixed 😉🤫
zhlédnutí 2,1KPřed rokem
Hi Guys, In this video I will show you a common issue with door lock and how to fix/ replace it. Easy repair at home, save on labour. Thanks for watching! See you soon 😉
Part 1 # ZANUSSI Washing machine E40 error message on display. Door won’t open door lock issue 🔒🤬
zhlédnutí 907Před rokem
Hi Guys, In this video I will show you a common issue, if you are interested how to fix it watch the next video. Thanks for watching 👍 See you soon 👋
ZANUSSI LINDO 300 Washing machine door lock doesn’t open, how can be fixed easily, was stuck. 🤨❔❓❔
zhlédnutí 18KPřed rokem
ZANUSSI LINDO 300 Washing machine door lock doesn’t open, how can be fixed easily, was stuck. 🤨❔❓❔
Water collecting at the bottom of your fridge💦?? How to stop it✋?? Easy fix 😉 Watch this video!!
zhlédnutí 254Před rokem
Water collecting at the bottom of your fridge💦?? How to stop it✋?? Easy fix 😉 Watch this video!!
Part 2# Beko Condenser Tumble Dryer. How to fix it when empty water tank appears on display …😠🤬
zhlédnutí 30KPřed rokem
Part 2# Beko Condenser Tumble Dryer. How to fix it when empty water tank appears on display …😠🤬
Part 1# Beko Condenser Tumble Dryer Empty water tank warning appears on display, stop after a minute
zhlédnutí 16KPřed rokem
Part 1# Beko Condenser Tumble Dryer Empty water tank warning appears on display, stop after a minute
BEKO Washer-Dryer doesn’t work. The Tumble Dryer section not heating up. How to reset the sensor?
zhlédnutí 4,2KPřed rokem
BEKO Washer-Dryer doesn’t work. The Tumble Dryer section not heating up. How to reset the sensor?
Pride Apex Mobility Scooter battery replacement with a little trick 😉
zhlédnutí 2,4KPřed rokem
Pride Apex Mobility Scooter battery replacement with a little trick 😉
Burnt smell from your tumble dryer? Beko, Hotpoint, Indesit, Bosch, etc. Easy solution, easy fix 😉
zhlédnutí 2,4KPřed rokem
Burnt smell from your tumble dryer? Beko, Hotpoint, Indesit, Bosch, etc. Easy solution, easy fix 😉
Pride Go Go Elite Mobility Scooter Don’t Move Only Beeping. Battery Indicator Led Shows Half Charged
zhlédnutí 1,4KPřed rokem
Pride Go Go Elite Mobility Scooter Don’t Move Only Beeping. Battery Indicator Led Shows Half Charged
Fix Indesit/ Hotpoint Condenser Tumble Dryer. Empty water warning light is on and doesn’t heat up 😱
zhlédnutí 23KPřed rokem
Fix Indesit/ Hotpoint Condenser Tumble Dryer. Empty water warning light is on and doesn’t heat up 😱
Hotpoint washing machine F05 Error Code. Blockage. Don’t drain.
zhlédnutí 54KPřed 2 lety
Hotpoint washing machine F05 Error Code. Blockage. Don’t drain.
Noisy tumble dryer 🔊🔊How can you replace the bearing on your Hotpoint/Indesit tumble dryer at home
zhlédnutí 7KPřed 2 lety
Noisy tumble dryer 🔊🔊How can you replace the bearing on your Hotpoint/Indesit tumble dryer at home
Hotpoint tumble dryer won’t heat up. How to reset the heating element thermostat if not getting hot
zhlédnutí 76KPřed 2 lety
Hotpoint tumble dryer won’t heat up. How to reset the heating element thermostat if not getting hot
Pride GOGO Elite Traveller Plus Mobility Scooter. Don’t move only beeps 🔊🔊🔊 I show the trick😉
zhlédnutí 19KPřed 2 lety
Pride GOGO Elite Traveller Plus Mobility Scooter. Don’t move only beeps 🔊🔊🔊 I show the trick😉
HOOVER Washer dryer 8+5kg makes a horrible scratchy noise 😱 Maybe the bearing❓🤔
zhlédnutí 10KPřed 2 lety
HOOVER Washer dryer 8 5kg makes a horrible scratchy noise 😱 Maybe the bearing❓🤔
🚘 How to reset the service light (Arrange Service, Key Sign) on Citroen Xsara Picasso 1.6 hdi 🚘
zhlédnutí 813Před 2 lety
🚘 How to reset the service light (Arrange Service, Key Sign) on Citroen Xsara Picasso 1.6 hdi 🚘
Como desbloquear sabras
Where does the blue wire connect to at the top?
I'm experiencing a similar noise with this model. So was the shoe lace the source of the noise? Did no parts needed replacing?
Hi, In my case the shoelace was the issue, I needn’t any parts to replace
@@georgesworkshop8600 thanks, I opened it up this afternoon and found some wear around the bearing. But also found some chewed wires. A mouse must have got inside. So I've to more parts to order.
I hava a beko WTA8612XSW with the same shaking problem. The internal components, and the exterior is similar to this model, i presume. Tomorrow I will diagnose the problem. Thank you for the awesome video and your DIY method.
Thanks and good luck 🤞
Today I managed to changed the rubber sealer with help of my 12 yrs old boy. Thanks to your deatiled video we managed to save money of 300 +EUR which was asked bv Beko company technician . All went good putting back the second ring to the rubber was challenging but we did it with help of my mother+12yr😅.Thanks alot again for sharing video's like this very useful and detailed video
I’m glad to hear that you could fix it. 👍
180 degrees out. Do your reserch before making a video 🙄
My one the rimers are out on mechanic do you know why tis would happen.and do you knw were the sencer is
Hi Lilly, Sorry, but I don’t know what do you mean. Could you please give more information? Thanks
I cleaned it and it worked well thanks
Just got one of these mint but second hand watching these video's before I use , mine is 8kg 1600 I thought if you got a 8kg machine you could put upto 8kg in it but the manual seems to say you can only put 3 kg in on daily 59 wash am I reading that correctly as this seems daft if its a 8 kg machine must admit im a little confused regarding this and I can't seem to find any viedos for this machine that helps clarify this , so if someone can explain I would be very gratefull even on mixed it seems to say you can only put in 4kg so whats the point of it being a 8k machine...??? And will / could it damage it if you put more in even if its under 8kg doesn't any make sense to me ...
Hi Karl, The reason for that a 3kg dry load will become 7/8kg wet load. If you exceed the recommended weight limit a couple times it won’t happened too much, but if you regularly do the same that will shorten your machine life.
@georgesworkshop8600 hmm ok thanks for the reply...
Thanks for your help should have whatch video be the wife ordered a new one 😮😮😮😢
Next time? 😉
Hi George!, Thank you for the repair explanation. I have the same error. I slammed the door a few times and it started working again... for a while. The lock mechanism works; locks; unlocks fine(I have to wait a while before it unlocks). It just doesn't seem to be convinced the door is locked. Would you think that that is some dirt in the mechanism or the electronics board? Highest regards, Mac
Hi Mac, I don’t think is there any dirt in the lock mechanism. I’d rather say the stick that is going into the mechanism is worn ( rounded down) and the mechanism can’t hold it firmly.
@@georgesworkshop8600 🤔yeah. Well I changed the doorlock. It still complains. It works when i push the door extra tight. Pin looks fine. Maybe the door is offset at the hinges. Maybe the lock is offset and i have to move it. Did some laundry though. So I can at least try to fix it in clean underwear 🤓 Thank for the help👍🏻🙋🏻♂️
Thanks for this. Now have a fully functioning scooter
Thanks Victoria! 😉
Thanks 👍
You’re welcome
Helped me bud, thought our drier was toast. Need to let it do the cool down at the end of its cycles.
Glad to hear that! 👍
I used a straightend safety pin to reset it.
Good idea!
Thank you, this worked a treat! Great video!
Thank you!🤩
Monday I will be receiving the rubber sealer which I ordered for Beko WTV 7712BLS hope that,too same way needs to change the rubber sealer.
Good luck, maybe will be better if you have extra hands around to hold the springs when you will return them. I get used to ask for help too
Looks good and legit for me (even procedure is not completely right) But ... How long "WD40" last after apply it? I reccomend you some good UV spray or even some ceramic coat. But Ill try your solution, propperly done. Ill share how long WD40 last (I bet you only few days with luck)
Hi, I wanted to show a domestic, cheaper solution . I know there are professional solutions with professional products
I had no heating so i took panels off then looked at heating element - and it was now working! I put it back together and put a few towels in. Checked it after a while - drum not turning! I saw belt snapped. Bought new belt put it on. Heating working and drum turning but Empty water light' on.....and no water in top collecting tray! I pulled that plastic cover off the back and water in bottom. I removed water. It's been kept a clean machine. blew down pipes all good. So, how do I know if the pump is not working? And how would a faulty pump affect the heating event?
Hi, Firstly, if the pump can’t pump the water into the upper tank it will stop the machine to avoid from more water in the bottom tank. May just little paddle need to replace not the whole pump.
@@georgesworkshop8600 Thanks will check that out
@@georgesworkshop8600 Hi I looked at the paddle it was worn. But i check on eBay the only ones i see all look the same as mine but my Indesit IDC8T3 is not listed on the eBay lists. Are they all the same? Just wondering if you knew at all...they're only a few quid anyway to buy.
my wife found a bit of metal in the clothes and threw it away. When she described what it was I think it was the sensor bar. Do you have any ideas where it fits as I can’t really tell where it’s missing from?
Hi, One place could be where the daily filer located. You need to remove the filter like clean it. Or, in the inner plastic frame of the door, on the top. It’s better to remove the front cover while you fix it.
Good stuff 👏
Thanks James
Top man👍👍Coins and crusty bits and the ball float thing was stuck. Cleaned and sorted..Thank you!
What a great news! I’m glad you could follow my advice
This looks like torture, but maybe I can do it after all Thanks for this great video.
Hello, I hope you’re able to fix it.
Thanks, fixed my issue.
Great job! 👏
Since he missed out a lot of relevant info... The battery box is held in position on the scooter by its power connector on the underside of the box, plus Velcro style tape, and gravity. To remove the screws on the bottom of the box... I can't tell the size, but he used a long 'cross head' screwdriver - also referred to as a 'Phillips head' screwdriver - and then a little magnet on the end of an extendable stalk. Assuming most people don't have a magnet... The screws will fall out of their holes when you turn over the box to be able to lift off the top cover. Make sure you keep track of them when they do fall out. If you put a small piece of sticky tape over each hole before you turn the box over, the screws will stick to that and not get lost. The two batteries inside the box are standard 'deep cycle sealed lead acid' batteries. They're '18-12' batteries. (Also known as '12v 18Ah' or 12 volt, 18 amp hour batteries.) You can get various different brands and styles/capacities on Amazon and eBay, Walmart, Autozone, Nappa, etc. He didn't share what size socket/wrenches he used to remove the wires from the batteries, but to be honest yours might be different anyway so that's forgivable. The batteries are held in place by more Velcro style tape which is why they needed to be wiggled & pulled up. He replaced the original batteries with two slightly heavier & longer lasting ones = 12v 22Ah. He did not replace or even reuse the Velcro tape on the bottom of the new batteries, but you really should use it, for safety sake. Many batteries come ready charged. However, they'll hold more charge and last longer if they're fully charged again before being used, ideally for 12 hours. That can also be done using an ordinary car battery charger before they're installed if you can get by with using the old ones for a while. You're welcome. 😁
Hi. I followed your video tutorial and was able to replace the hose in my washing machine. Thanks! I have another problem now. My washing machine drum won't spin even when it is empty. It starts to fill with water and then stops at the point the drum would start spinning. I can drain the water so I know none of the hoses are clogged. The belt is on the wheel at the back of the machine correctly and not worn out. I plan on buying a new washing machine in two months when we move, and would really love for our current washing machine to last two more months if possible. Does this sound like something I could maybe fix myself? Do you think it's a sensor in the machine that controls the belt? That sounds like a job for a repair person. Thanks so much for your help.
BTW. It is a front loading Blomberg machine. I checked the filter and it is not blocked.
I also tried closing the door six times to do a reset, but that didn't help. The door does lock when I try to start a wash. Does that mean that the door lock is ok?
Hi, To replace the waste pipe shouldn’t have effect on spinning. Have you checked the carbon brush? If it’s worn out not enough power to move the drum. I have no other idea without testing.
@@georgesworkshop8600 thanks! I looked up carbon brushes and it sounds like this could be the problem. I will probably have to call a repairman. Thanks for your help!!
@@georgesworkshop8600 you were right! The carbon brushes needed to be replaced. I had a professional repairman do it. I will need to get a new washer eventually. What brands have the fewest problems and are the easiest to work on? Some seem like you have to take the whole washer apart to get to the parts inside. Thanks!
Я замінив шланг і почалися проблеми з барабаном, починає дуже швидко крутитися і зупиняється
Hi, To replace the waste pipe shouldn’t have effect on spinning.
Love to watch an expert working going to strip the machine down tomorrow 18 /06/20024 thanks for video 😂😅😊
I hope you’ve succeeded your mission.
Thank You!
Thanks! 👍
Thank you so much. You saved me some money
Good to hear that you found it useful .
Explained very well.. thank you for your time..
Thank you for sharing your experience! 👍
Thank you
Thanks! 👍
E01,lock E02,fill E03,HEATER E04,forgot E05,ntc
Thank you
Thanks but finding it so hard to put final spring on
I know, many times I must ask for helping hands.
Thanks for sharing this demo! It has resolved the issue on my Candy SmartPro Tumble Dryer
Great to hear that! Thanks
Man i love youtube Great video great help Bloody covid mask 😷 Thank you so much mate saved me a packet You the man 👍👍👍
Thank you!👍
It makes me irrationally angry Google puts the most scammy/bullshit ads on videos aimed at products for the elderly. Not the fault of the content creator, but good lord.
I hope you found what you were looking for.
@@georgesworkshop8600 I did, thanks. This helped a lot.
I have the same machine same problem,fitted new heatsing element and control board same problem no heat,all lights flashing after few minutes,at a loss now
I have only one idea let’s check the pump. If it doesn’t pump the water could stop the program.
Good presentation "how to" - no distracting mindless talking, simple point with finger etc. very easy to follow.
Thanks mate
@@georgesworkshop8600 Yeh, so I took off the door seal as you showed, great. It has two wearout "tears" where the folds seems to have rubbed on themselves (design fault?). Anyway Beko parts come every quickly and not expensive (£40 with fast delivery). After seeing your vid I have made a special tool to spread the door band spring (bit like external circlip pliars), I will be doing a solo install and a spring spreader should make this job go well. Thanks again :)
Can you help with my dyer it’s not getting hot
I can’t help sorry, I’m on holiday…
Thank you so so much! This worked on my moms drive scout mobility scooter, I just put new batteries in and the dumb thing kept beeping 5 times red lower left red light with full batteries and I had already switched it from neutral to drive but not correctly with the key off! Thank you Thank you!
I’m glad you could sort that
I have this tumble dryer but my control panel doesn't light up and no sound when i move the dial. I've checked the socket and the fuse nothing wrong there. any idea what what i can do fix this please.
Hi, I presume control panel issue. To replace it is quite pricey. Not sure if it’s economical to replace it. I can’t be sure as haven’t seen it.
Thank you!
I hope you found useful my video
Before even pulling the element out, couldn’t you have just ohmed the connection points to see if you are reading high ohms?
Many times when tested it seems ok, won’t diagnose physical damage like rust.
@@georgesworkshop8600 true
Another happy subscriber. I heard the click and knew I was onto a winner. Gent for sharing this
Congrats mate! 👏
I love you. ❤
🥰😉
i had 5 beep...now i have 9 beep...more beeps the worse..these scooters shouldnt be so unreliable require much repairs especially for disabled
I can agree with you.
What would be the causing this error E41 or E40 if the door lock has been changed? My washing machine tripped the main fuse and now keeps showing E40 error. Bought a brand new door lock, still the same. What would be next steps of fixing?
Hi, has been moved your machine recently? If yes, maybe wiring has damaged.
@@georgesworkshop8600 Not been moved. It's an integrated unit. Did you mean the wiring between the door lock and the control board?
OK, so watched your video after my dryer stopped working. Bought a new drain pump motor, but the 'wheel' in it spins, before i even lift the metal thing or select a program or anything 😂 what am i doing wrong?
Hi, I don’t think you did anything wrong. This is quite normal. When it switched on the machine starts with a short pump, probably you seen that. Is the program running?
Useful to watch at night if you can’t sleep.
I think music is fine, it kind of calms you down, and not you get frustrated 👍
Thanks Pete!