Video

Thank you, the drain test code 12 is very helpful! I was using a shop vacuum ... I left my machine off for an hour, and it started working again. it would not spin.

Thanks for the video. So i ran the diagnostic and got the 7-1. After it cycled I tested the heating element and it was sizzling...so now what?? Is the issue fixed now??

Thank you Kraig

Have an E1 error, what steps can I do to fix it?

Thank you!! Couldn’t get anyone out to work on ours so I ordered the part and followed this video!! Tadaaa it works 😂❤

My dishwasher is not running hot water. I had an appliance guy come out and tell me that since it's pulling the cold water from the line, it needs a circulation pump to get hot water in there and for that, I'd need a plumber. He said the heating element is secondary to that issue. Does that sound right?

Thanks!

No offense but May was well wash by hand in a bucket and soak and wring.

Well done!

Washer fixed. Thank you. Joe

I have same dryer it’s lighting but it only stays on for like 10 seconds then goes right off. Takes forever to dry and clothes are super static and in clumps wrinkled. Would that be one of the limits bad? It was working fine I changed belt and shop vac cleaned it I looked to see if I busted any connections I didn’t see any. It’s makin me mad not bein able to figure out and don’t wanna buy every part for it and fix no it’s something simple I’m sure

got it wrong fella it s mainly lack of sufficient agitation. to many cloths stuff in there

Great Video! I’m going old school and just manually washing dishes. Dishwasher will be used for storage 😂.

This video just helped me to get my dishwasher working again. The “clip” information was the fix, thanks!

Timeless Vid just fixed mine with Identical issue easy peezey Thanks Bro!

You didn't troubleshoot or diagnose anything. You just changed out the ice maker.

Dirty clothes would have been a much better demo

Where is the directions? This is just a commercial.

Pressed & held switch 1 LED lights went off & would not come back on. Unplug unit & disconnecting control unit & reinstalled and still no LED lights light up when plugged back in. Replaced control board with a new one & LED lights came on UNTIL I learned I needed to hold light switch & switch 1 button at same time. Now I’m back in the same situation with no LED lights coming on & the compressor doesn’t even attempt to kick in. This is a standup freezer. WZF35X200DW01

Great Vid Jimmy!! Thanks for all of your help on this big bud!!

Thank you. God bless

Ok so what was the problem? How do we know it was the icemaker?

GE DRYER NEW I AM ON # 5 tech. They cant fix my dryer

shit video

Where can we buy the latch?

water line buddy didn't fix it. Out of ideas...

So i i get the lid lock noise and E3 on first two its likely my lid or would it be my drain

Can you send the link for this two-piece kit? Thanks

Great video… Can you explain why it was necessary to replace the latch? What exactly was wrong with it? Thanks

Hi. I have the same model in the video. My problem is my machine when it gets to the spin cycle, it does not spin or rotate the agitator. It does everything during the wash cycle as normal but won't spin the clothes. No fault codes either. Any help would be great.

Podría ser en español gracias

Was able to replace the heater and thermostat relatively easily due to your clear, concise instructions. Thanks!

We replaced the basket hub but the SD code is still showing. Do you have any suggestions of what we should try next? Your videos have helped us with our washer (older ones long gone) and our dryer. You're a highly trusted resource.

Rent the video for 8$ on your site? Fuck off...

Getting an er FL on Speed Queen

I have this same dishwasher, it drain put doesnt do anything else, it comes up with heavy and smart flashing. anybody know why? thanks so much

Great Video. It's 10 years old and I can see people are still using it. Thanks for helping us kitchen mechanics!

bless your freakin heart. was sure I'd have to buy a new microwave.

I got error 9c8 model WA50B5100AV

great video, exactly what i needed

When I lose power, I get the E7 code. How do I reset it? When I get to the number 1setting in diagnostic it turns into the digit number 7. I have tried to go to 13 in diagnostic to clear the code, turn on/off and back on; it does the same. In the past, I unplugged it for a couple of days, then it would work fine. You have to have the easy fix for me, I can't wait for days.

No common sense of redoing the video after your hiccups stopped instead of torturing us and yourself.🤦

Thank you for this video! Slightly different model of Samsung microwave and the clip the spring attaches to was broken. I attached the spring to one of the brackets and it’s good as new… for the moment 😂 thanks for helping me limp along if only for a bit longer!

Thank you sir. And yes my Maytag washer and Dryer are still working after 28 years.

I have this exact washing machine, but when it starts running water it doesn't finish snd starts draining all the water back out before washing any. Can you tell me what the problem might be pkease?

Washer Whirlpool Duet code F-20, What's the problem ?

Bravo! Bravo! great video. helped me fix my fridge. thanks matt

Hey Neighbor, Screw came out on one side of our stove similar to this one. Watching the video really helped. I removed the two outer screws on top of the door which allowed the frame to come forward enough to remove the handle assembly. Reinserted and tightened screw that fell out and tightened the right side screw which was also loose. Put handle assembly back and put two outer screws back into the door to hold the outer frame. About a 5 minute job. Showing how the plastic frame and the handle assembly attached really was beneficial. Again, I appreciate the video.

1:43. Thanks, this helped me out alot! 😎

What was the point of that damn video