L. SCOTT BROOKSBY, IA,A&P
L. SCOTT BROOKSBY, IA,A&P
  • 29
  • 11 693
preparing a die to wax a crown
The laboratory process to prepare a die to wax a crown
zhlédnutí: 94

Video

Waxing a pfm crown part 1
zhlédnutí 9Před 2 měsíci
waxing a PFM crown part 1
preparing a cast for die preparation
zhlédnutí 297Před 2 měsíci
shows how to pin and create a base for a crown
waxing a pfm crown part 2 and spruing it
zhlédnutí 43Před 2 měsíci
shows how to wax and sprue a PFM crown
overdenture wax up
zhlédnutí 160Před 2 měsíci
introduction to creating an overdenture, lab waxup.
orthotic flipper
zhlédnutí 29Před 10 měsíci
This is how to make a night guard flipper combination for those that need more strength and protection of the remaining teeth. This is also for those that need a flipper, but the bite is overclosed.
flasking an orthotic
zhlédnutí 661Před 11 měsíci
flasking an orthotic
creating the space for bleach on a bleaching tray
zhlédnutí 17Před 11 měsíci
creating the space for bleach on a bleaching tray
spruing a gold crown
zhlédnutí 22Před 11 měsíci
how to sprue a gold crown for casting.
how to make a heat cured orthotic or night guard
zhlédnutí 20Před rokem
how to make a heat cured orthotic or night guard
rebuilding a hose with an AN fitting part 3
zhlédnutí 17Před rokem
rebuilding a hose with an AN fitting part 3
installing an AN fitting into a hydraulic hose part 1
zhlédnutí 22Před rokem
installing an AN fitting into a hydraulic hose part 1
what to do if the drill bit stays stuck in your hose part 2
zhlédnutí 24Před rokem
what to do if the drill bit stays stuck in your hose part 2
lower denture flasking
zhlédnutí 11Před rokem
lower denture flasking
flasking a denture
zhlédnutí 9Před rokem
flasking a denture
preparing the impression for an implant supported Crown when the transfer coping comes out.
zhlédnutí 26Před rokem
preparing the impression for an implant supported Crown when the transfer coping comes out.
adding The gingival Mask to an implant impression
zhlédnutí 314Před rokem
adding The gingival Mask to an implant impression
seating implant abutment on the analog in an impression
zhlédnutí 20Před rokem
seating implant abutment on the analog in an impression
pouring a pickup impression
zhlédnutí 1,8KPřed rokem
pouring a pickup impression
pouring the opposing cast
zhlédnutí 22Před rokem
pouring the opposing cast
pouring the cast in the triple tray impression
zhlédnutí 173Před rokem
pouring the cast in the triple tray impression
setting the pins and preparing the articulator for a triple tray Dental cast
zhlédnutí 21Před rokem
setting the pins and preparing the articulator for a triple tray Dental cast
evaluation of the muscles of the head, neck and shoulders
zhlédnutí 12Před rokem
evaluation of the muscles of the head, neck and shoulders
comanche 250 bungee replacement by Comanche Blake
zhlédnutí 4,2KPřed 3 lety
comanche 250 bungee replacement by Comanche Blake
Steering rod boot alternate location comanche 250
zhlédnutí 157Před 3 lety
Steering rod boot alternate location comanche 250
310 landing gear reseal part 1
zhlédnutí 528Před 5 lety
310 landing gear reseal part 1

Komentáře

  • @lewaynegarrison8796
    @lewaynegarrison8796 Před 2 měsíci

    There is a so much safer and easier way to change a bungee on a PA24. I would never use this method.

  • @Lee-rp6kk
    @Lee-rp6kk Před 10 měsíci

    Poor way to remove a bungee under a load. Tool should never go banging around.

  • @bigc1903
    @bigc1903 Před rokem

    This is the wrong way to remove and replace the bungee. Very BAD tutorial. Spend the money and buy the tool.

  • @adamsito7670
    @adamsito7670 Před rokem

    Promo*SM 😠

  • @babysnuggslm
    @babysnuggslm Před rokem

    Do you place any tin foil on the flipper/partial before you pour stone on it?

  • @sixthsenseamelia4695

    51 grams. Lol.

  • @sebastiangrebe8276
    @sebastiangrebe8276 Před rokem

    I dont know much about Medicine, but i woud buy a Scale that shows 2 Decimals past 0 for medical Mesurements.

  • @Captndarty
    @Captndarty Před rokem

    Roughly How much time and money would this add to a cost of an annual if you did it yearly?

  • @doktorfixit
    @doktorfixit Před 2 lety

    Hi Scott, Very nice video. Please tell me how you shot the view of the outboard roller bolt being screwed into the nut plate in the rib.

  • @pa24comancheguy11
    @pa24comancheguy11 Před 2 lety

    Thanks for the video, new comanche 260 owner here. I was trying to visualize how exactly the bungees worked and this was perfect!

  • @frankgh1
    @frankgh1 Před 3 lety

    I cut them off, slowly. Just a few strands at a time. To reinstall, I lower the gear manually on to an old tire so they don’t go down and locked. That way I can manipulate the gear by hand while under the wing. It makes it a one man job.

    • @stevenvlog8398
      @stevenvlog8398 Před 2 lety

      Lower the gear manually onto an old tire, how does that work?

    • @frankgh1
      @frankgh1 Před 2 lety

      @@stevenvlog8398 Jack the plane. Raise the gear. Position an old tire under one side of the main gear. Release the manual gear extension mechanism and gently lower the gear until it contacts the tire. Now you can move the gear up and down from under the wing. It makes getting to some of those grease fittings easy too.

    • @stevenvlog8398
      @stevenvlog8398 Před 2 lety

      @@frankgh1 thanks so much! I think I saw this from the Comanche tip as well ( put a wood block on nose wheel achieves similar)