Video

❤

😂😂😂😂👎👎👎👎👎👎

fab work is a bit shoddy but otherwise clean build bro!

10.41 into the video you did a test run of the motor.. It looked like it was off-balance and had a small wobble. This is not safe.. Also, your battery pack is a fire waiting to happen. Don't leave this thing unintended in your home even if it's not being charged. The whole thing of a death trap. But,,, at least you can say you tried. 🤓

None of the above links work. Thanks for the video, more clear info on the wiring and battery would be good though.

i see everyone changing sprockets, why notjust leave the larghe one from the peddle on and have geared back wheel sprocket? there is more than enough torque on the motor... what you did there is a waste of time. leave the small sprocket at the back.

None of the purchasing links work mate. Thanks for the video, I would love to know where the little shank wheel comes from.

I just dont get why his using masking tape to cover the battery's up surely that's a fire hazard it's not made for that masking tape is made for painting lool 😂😂😂

twin motor is faster and can last longer. single motor can easily overheat and burn.

Tire will worn out quickly where motor rubs.

Cool

Dont do this without a spring tensioned chain. Direct like that its a toe chopping machine

It would be useable if it would have pedals. This tiny motor and small battery are good for assistance but not as the only power.

The loose dangling finger socks of your glove can get caught in the saw teeth and with them two or three of your fingers. It is costly trying to sew them back together you know.

И что бы мы делали без гироскутеров ...

What is that cylinder in the bottom bracket?

very good sir ,So beautiful very nice car

Chế tạo boom

Nice

Need this project broo!!!

Ham ko bhi chahiye bor

Put a dual chainring on the front and a 7 gear derailleur setup on the back Moosehead motor to the outside of bottom bracket put the cranks back in get a second chain then make a short chain to go from the motor to the smaller front sprocket and a longer one to go from the other front sprocket to the back derailleur like a normal setup so you can leverage the gears and get a lot of more out of that likely 10 or less newton-meter motor just like a typical mid-drive with gears like all the cool kids have instead of direct drive with no gears and your fuel put free wheel on your cranks it should feel quite natural when you're pedaling and when you're not I think but you know a lot more about bikes than I do so I'm pretty confident you'll figure that part out

What's your approximate maximum range and top speed?

Hola, aqui en Mexico en que tienda venden el motor, y si es asi cual es su direccion, yel nombre del expendio.¡ me gusta la coneccion!!

i wonder if i can just simply put a hub motor and the stock hoverboard esc and bypass the on/off thing and manually put the sensor on the bike pedal so i just move my feet to move, im so stupid and smart i just might do it and i get a free battery pack installed that has a charging circuit

Bhaiya mujhe ye drone chahiye aapke pass avelable h kya

Boa noite fiz o mesmo sistema igual ao seu mas o motor d hoverboard esta esqueitado o q pode ser se puder me ajudar agradeço

Is this battery protection circuit can work on power Bank module

Fuse voltage ?

Use 4x motor with speed controller.

You need to install one more hoverboard motor for make it run faster ⚡

ये मोटर वो नहीं है जो पहले दिखाई ये एक्जास्ट फैन मोटर है भाई

Делай натяжитель с успокоителем внизу перед большой звездой и будет долго работать а так молодец всё ок.

А сразу не догадался звёздочки наоборот.хотел 120км в час.😂

Найкраща саморобка на базі гіроскутера

Puikus hobis.verta pabandyti

Good luck my dear friend good

Invertí las relaciones pero atrás ponele una con velocidades de esta forma no le costará al motor lastima y agarra más velocidad. Si tenes la otra llanta ponérsela en frente. E irá más rápido y no costará la salida.

Great project

Bohot atcha haa i love 😗❤️

Y otra sugerencia a todos esos cables sueltos les hubieras puesto y uno grueso de color negro un fideo grueso donde estubieran todos los cables y te evitas meterlos todos juntos por el agujero

Todo esta muy bien hecho excelente pero por que no pusistes el chucho de encendido de la yave en el manubrio es mas facil por que si la llave se afloja se cae y pierdes la llave

Notebok batery ?

Parchesh link

please give circuit diagram

what number diode you used?

I want this one please

shoulda got a bike with rear gears. could lower or raise the ratios :) more speed or more torque when needed

I set up the same circuit with Tp4056, but when I connect the plus and the minus in series, the tp4056's light turns red and does not work, it cuts the voltage.

Which size on barring balls?