Video

Best cap gun

Genius!! Same problem and same solution - worked!!! Thank you!!🙏

Praise Jesus, I gave up already, then had to try again since newborn baby can't stand the occasional cold shower. Your method worked, though I tried a bigger bit after almost completely drill through the set screw. Who in their right mind would design such a pain in the rear!? If you have a water softener installed, this is a must happen, since there is added salt in the water. PRL for your video! I was praising Jesus with my brother in law in the bathroom after taking out the screw. Haven't been this happy for so long!

Thank you Jesus for this video ! Thank you for posting, saved me from the destroying half the bathroom trying to removed this screw.

HOLY COW!!! THIS WORKED!!! Only I used just boiling water. Mine has been stuck for over a month. I boiled the water & poured over the button on both sides. My steam button is on the undercarriage of the arm. I took a knife & the button released with the first pull. I am soooooo happy!!!

Mine is Hex, but Metric. None of the SAE “Us” Hex are even close. Also there was a recessed cap, I had to remove using a Jeweler Screwdriver. I threw this away.

I just bought one with the same problem and my research said it is most likely a stuck valve. Put it in a warm place and let it sit there a while, then try to start it. We had a couple of warm days and it was in my shed. Guess what. It started in three pulls. I always start mine periodically throughout the year. That will most likely fix your problem.

Thank you. I couldn't see in there..

Thank you so much! Screw came right out, now I need to figure out how to remove the stuck handle 😂

Thank you, it helped me, I lost over 286 Pound 😁

1. Thank you Anil 2. Moen - WTF is wrong with your engineers? 3. Thank you Jesus

I believe muskets are more scary than modern firearms because you don’t know what is gonna happen with such an old weapon

Unfortunately, on my American Standard shower handle, this didnt work for me. However, I ordered a new cartridge which comes with a hex key that fits right into the set screw. I'd gone from hours scratching my head to loosening the set screw in seconds with the hex key. If you cant get the set screw out and its not stripped, it might be better to get a new catridge/handle assembly from your tub's manufacturer and use the tool that comes with it for the set screw.

You are wonderful!!Thank you! I wasted so much time watching other videos that didn’t resolve the issue and you delivered the fix in only 1:43 !!! (not 8+ minutes)

Thank you for thanking Jesus and for this video! Exactly what I was thinking- that the set screw was stripped.. I am thanking Him too and hopefully I'll be thanking Him more when I fix it.

Ilove amerika!

Just a heads up, some set screws are a standard SAE hex and some are metric. If one doesn't work, try the other.

Thank You, I found an old T15 Torx screwdriver and came out easily. This was after much frustration of using my old Allen wrench set and no luck, than going out and buying a new Allen/hex wrench set with different sizes and still no luck. Than I watched your video and tried a T 15 Torx screwdriver and came out so easy. Appreciate you.

this ia the most important video of the last three years and beyond. thank you for your time and energy

HELPFUL. I GOT MINE OUT WITH A TORX BIT AS YOU SUGGESTED. THANK YOU

This was great! Thank you so much for this Tip!!!

This was the 5th video I watched about removing a stripped set screw after I just installed a new trim kit and already messed up the set screw and was about to start trying a few methods. After seeing your vid I went to try once more but this time I tried hex bits, but they were too wide to reach the screw through the handle hole. So I tried a different allen wrench set from my same tool kit and soon realized the 2nd set had one that fit better than the first allen wrench set and the screw came right out 🎉 Literally just now finished and ran back here to Thank YOU and thank Jesus!!!!!!!😄😄😄🙏

Thankyou so much

I got it! Thank Anil!

👉 P r o m o S M

Doesn’t look right. Prefer spinning rings.

Thanku brother , saved me a lot of expenses.

True talent.

Thank you for posting this video! It saved me so much time and headache!

Thank you Jesus! T15 tapped in solved the problem in less than a minute. You are a genius!

The correct size is 7/64"

My husband just yelled at me”Thank you Jesus” after I sent him this video and he followed your instructions. Thank you sooooo much for posting!!

Mine striped but will be trying this tomorrow! Otherwise new hands it is haha

Thank you. You saved me. I was about to drill it out. This trick worked!!

Absolutely. This video saved me from some serious headache. The T-15 bit worked like a charm. However I did not have to hammer mine in. It fit perfectly and I had it out in a matter of moments. Yes agreed the thank Jesus part was the best

Dang I wish I would have watched this before I drilled into to.

Thank you very much for this recording! It would have been unfortunate if such moments were lost. Thank you also for the love you surrounded her with. P.S. It is worth noting how at minute 9:12 our beloved Laura looks gratefully towards God.

Her voice matured and got so strong she from now on can sing in spaces without amplification.

Your a lord send my friend

Unbelievably helpful, thank you!

Laura: seja isso : uma voz santa para sempre. Pela idade que tens nao vai acabar sua mocidade e terna jovialidade . Não vais envelhecer. Serás uma eterna mocinha quando o Mestre voltar. E assim viverás. 😊😊 seja feliz . Faltam só alguns anos. Serás uma eterna santa cheia de vida , alegria e bênçãos.

Superb!!!😘

Oh my. Laura your beautiful ❤😂🎉😊

Great song and voice, but not so good kamera work.

This was the same song she sung the very first time I ever heard her, the first time she was on America's Got Talent, when I fell in love with her voice forever!

La mejor voz que he oído increíble ❤❤❤

🌈❤️🌹

Where can I get that kind of American flag

👏🌹❤️

awesome🔥🔥🔥🔥