Video

Any updates now about this engine and super tech oil?

not bad at all supertech motor oil I used my in my Mitsubishi outlander, super happy with it and satisfied using the HighMileage synthetic one

Where to buy fake one? Amd how mich is it?

I use Super Tech & Fram TG filters, that will drive the know-it-alls crazy.

Let’s just say you keep a car from 10 miles to 250,000 and change the oil every 3500 miles. That’s roughly 71 oil changes. Would you rather spend around 2k using a good store brand oil or spend 4k + using brand name. I’ll go with the store brand. My opinion is what it is and I think the oil filter is the one to spend money on between the two.

Oooof that’s bad

Clean machine! Mine get 3000 mile or 6 month change! All clean too!

Dose it protect you from a c4?

I have this same setup on my Altima previous owner did it but I can’t find the right rotors for it. I’ve tried brembo 350z rotors but they touch the top of the caliper could I use the 12.6 rotors ?

Can you upload a comparison between the two? Would be interesting to see how to Chinese one differ in terms of material quality, stitching etc

both are probably made in the same factory

Just order from agilite themselves?

He flipped the gas tube lever up look closely

What kind of symptoms were you getting? Did this fix it? I've seen some talk about this code being thrown because of the camshaft sensors, but I've already replaced those.

Sieg Zeon!!

I've replaced both camshaft sensors, but I'm still getting P0365. What do you think could be the issue? (2006 Honda Accord)

I've replaced both camshaft sensors, but I'm still getting P0365. What do you think could be the issue? (Honda Accord 2006)

Which one you replaced, Intake or Exhaust?

Omg there’s fakes being sold? Please elaborate they’re sold by LE stores & have the same company name & markings?

Purchased mine from eBay because agilite was out of stock for a long time… fake???? I knew you have to beware with sneakers and stuff but how does one tell if the carrier is fake?? Other than color?

What all was done by psa ? Main thing here is can we see the wear on the bolt feed ramp? From what I’ve heard they need to polish the feed ramps

Hey sorry to bother you about this but I’m hoping you can tell me where you got the caliper? If you have a part number or something. Thanks so much

Can you compare them without pouches? Do they really differ?

Could I have the brand of tri magpouch you have there? On the K19 real one. It's looked pretty decent

This 🤡 Firearms is not for you buddy, stay at your patents basement. There is zero wear on trunnion or bolt

both methods will work scraping off the rust and the soldering one in my case I Hope this helps, I had the same exact problem on my 540i E39 on my passenger side tail light every light would work but one, my turn signal would not blink , I tried switching sockets from my working tail light to the non working one and no cigar, A Friend of mine tested the board on the tail light with some alligator connectors and a small battery all lights worked so that told me that she board is good ,I noticed the same corrosion on some prongs what I did , I wrapped a butter knife with a piece of paper towel and sprayed PB Blaster inside the tail light connector I let it soak for about 2 mins all You do is rub the connectors with the knife and towel until it looks clean kinda silver looking again , just repeat as needed Pb blaster brakes off rust that did the trick for me .

I changed way less parts on my 2006 Altima than on my 1990 Accord, so I would not say Nissans quality has gone down since 2000.

is that a tacticon armament

Goblin green 😂😂😂

Hello thanks for the video. Any updates? What did PSA say? Thanks.

PSA Is fine..but get a WBP 1200 RNDS NO issuses🎉

My Mak-90 from 1992 has less wear

i have a 95 Civic coupe but can’t find anyone competent to work or rebuild the ABS. i’m in SF Bay Area. do you know anyone that could help?

What Web site I can find the best Vvt Solenoid for my car V6 engine

Send it back the extractor cut on the barrel is wrong.

No update. Reveals alot about this guy that yells fire

So if it has a 7 on the bolt it’s considered OEM part?

Using garbage steel case ammo is the problem. 556 is best in brass. This ain't 7.62 AKm. People with no AK knowledge talking crap on PSA are the worst 🤮

Thanks.

In what order do the 2011 Nissan quest speed sensor harness cables go

I love PSA for what they are doing. I have a GF3 that has been flawless, and a 103 I had a small issue with that my local gun Smith took care of for me (bad head space) if they can get that QC to 100% they will be unstoppable.

Ck the chamber for concentric rings if they are present this is from the machine process when brass swells it can prevent it ejecting I have been able to correct it by polishing it with flitz metal polish and a power drill

what's your email

Hi Mate. I have a jammed Actuator and a non functioning solenoid any advise, could you supply these parts. I can send you pictures

Hi Mate, Is there a kit to service the Modulator, or just change the O rings for like for like rubbers

1:00 You used what? 😂

I am gonna be getting PSA 102 next

i know its been 4 months since a review but in hindsight i been debating between the Ak101/102 From Palmetto or the AOA FB Radom beryl's any advice which to pick? is the 101 worth it?

ugh. thanks for sharing