Video

Well if you do have 4 oxygen sensors, there are probably 2 sensors before the the catalytic converters and 2 after, the ones after are only there to tell if the catalytic converters are doing there job. The ones before comunicate with the ecu so if you have misfires, those could be the faulty ones I would try replacing both of the front ones🙂

@@_Project46_ thank you for the reply? You tell me that the after cat don’t cause misfire correct? That’s important, becouse 2 sensors are from the exhaust so the engine immediately cyl 1 and 4 and 2 and 3, then other sensor before cat and one after cat . In the real oem page the diagram name ones as lamba probe and other monitor oxygen so, what’s the difference and which one is the faulty? Thank you

Hi there! Im glad you liked the video, and thank you so much for the support, I really appreciate it🙂. Actually the clips are included with the cowl as well as the rubber gromets for the wiper arms so its pretty much all ready to be mounted. I wish you good luck with your project🙂 Kind regards Project 46

It could certainly be a faulty module, it never happened to me before, maybe a compatibility issue with your phone?

I mean, if it works, it works, might be faster as well🤔

Love you're suggestion! Thank you for sharing it with us🙂👍

The white connector is the one that goes to the cd changer so its useless🙂

Great suggestion! might be faster than the scraping technique😅

Glad it was helpful!🙂

Glad you liked it, and good luck🙂

The issue with these solutions is that in both casses the finish won't be as durable as a painted surface, and they'r also more expensive but sure it could work🙂

Must be a connection issue, does your phone connect at least?

Well thats surprising, have you verified your phone's sound settings to verify if the sound is stereo and not mono?

There is a blue latch holding it in place🙂

Honestly, its the biggest improvement that you can make interriorwise, it makes the interrior look like new again🙂

No, I only had one white connecter for a cd player, the other one might be for navigation but i'm not sure🙂

Glad it was helpful! Hope everything went/will go well🙂 Greetings from France

To be honest I don't really know, but I do think that the two systems are seperate units so if you have a standard buisness cd radio it could work...

I also had a very hard time getting the connector in place thats why its so important to release the white connector from the big one, I did not use any tools just persevearance. Hope this helps🙂

Je connais le problème, sa m'a pris beaucoup de temps pour remettre le poste en place moi aussi par contre le cable blanc qui était surement déja là c'est le cable de l'échangeur cd en option, sit tu n'as pas d'échangeur, il est inutile🙂

Yeah I know the pain... It also took me a long time to figure it out, thats why its so important to release the cd changer cable from the connector before pushing the unit back in place🙂

The first wire that I disconected was the FM radio antenna wire that goes to the rear window🙂

Hi Jaap, I'm sorry that this method did not work for you, to be honest I was worying about the same thing before I did it but after thurough testing with nail scratches I did not see any visible scratches apear, to be fair I haven't tried it with any metal object but but in general the finish on my parts stayed the same ever since. Maybe its a different paint or a different type of plastic?

Really glad you liked it! I wish you good luck, don't hesitate to comment how it went once your done🙂

Hi, thank you for the comment, the O2 sensor is the main component used for monitoring the engine's air fuel ratio and running conditions, if the ecu tells you the A/F ratio is to lean, it is getting that information from the pre cat o2 sensor, it might be a faulty sensor but it could also mean you have an issue with the injection system, a vacuum leak... Causing the engine to run lean.

Sa dèpend si tu as une radio avec lecteur cd ou avec cassette comme moi, normalement le mode cd normal ne serviras pas pour la bluetooth, il faudrait que tu essaie d'appuyer sur "mode" plusieurs fois pour que sa affiche cd-01, si sa ne s'affiche pas sa doit être un problème de communication entre la radio et le module bluetooth🙂

Well the best way to find out where the problem is would be to use an obd scaner to look for fault codes, I personally had the same symptoms with a permanent camshaft sensor code so if you don't have a scanner, replacing that sensor would be the first thing to try.

@@_Project46_ the problem is so random one day it will happen then when i restart the car its back to normal then i replaced the brake booster hose its cracked the problem went away then it came back when my mechanic scans the car no fault codes

@@mr.bricktop4894 yeah I know how it is, my problem was exacltly the same sometimes it ran perfectly fine and other times the idle would be eradic and the engine would stall...

@@_Project46_ am gonna replace the camshaft sensor and tps fist then see if it'll fix the problem

​@@mr.bricktop4894 sounds like vacuum leak. Should make a smoke test

Oui bien sur, j'ai mis les liens dans la description🙂

Well thanks a lot for the feedback, i'm glad you liked it that much🙂 thank you so much for watching my videos, i really apreciate it🙏

Well sometimes, I had random fault codes popping up saying there was an issue with the pre cat 0² sensor, and on top of that, a rough running engine with unstable rpm's after starting can indicate that the sensor preheater is bad. I hope this helps and I wish you good luck🙂

Oui c'est le désavantage malheureusement...

Est ce que sa le fait encore si tu appuie plusieures fois sur mode? Si non je pense que l'adaptateur est mal branché ou défectueux, regarde bien si le petit connecteur est bien branché surtout😉

Well, you just made my day🙂 i'm so happy you liked it🥲 i'm really apreciate your comment and i'm happy to hear positive feedback from my work thank you for watching my videos🙂

I didn't think of acetone but yeah that could work quite well i'll definitely try that next time🙂

I'm glad you liked, really apreciate your coment🙂, thank you for watching my videos... Of nee bedankt voor het kijken😉

Can't wait to hear from you if it worked with the hot water trick, keep me posted! As for the paint choice, it is indeed a good brand and I always got great results using motip. If I remember correctly, the laguna 3 has quite a lot of soft touch coating so I wish you good luck and thank you for watching my videos🙂

You won't have aux conectivity but you will have bluetooth🙂

I'm glad you liked it🙂

Is that problem occuring all the time or only in bluetooth mode?

Well that sounds like a much easier way to do it, on what vehicule did you do it? Cause the coating on my parts was really strong...

I had the same issue when I was installing mine, I fidled with it for a long time before getting it to fit, there should be just enough space in the rear left corner to fit the conector and if you have a preparation connector for a cd changer try removing it from the big connector before pushing the unit in place. I hope this helps🙂