- 48
- 984 710
DA64W DIY
Philippines
Registrace 3. 10. 2022
Replacing Valve Cover Gasket | Suzuki Every Wagon DA64W (K6A Engine)
This video shows how to replace the valve cover gasket. It can be applied to any vehicle.
Over time, the gasket wears out and may cause oil leaks, which can lead to engine problems if not addressed.
Over time, the gasket wears out and may cause oil leaks, which can lead to engine problems if not addressed.
zhlédnutí: 63
Video
How to Change Coolant and Bleed the Cooling System
zhlédnutí 996Před měsícem
This video shows how to change the coolant and how to bleed the cooling system.
How to Jump Start a Car Using a Power Bank | A Must Have Tool
zhlédnutí 256Před 3 měsíci
This video shows how to jump-start a car using a multifunction car jump starter power bank. Power bank car jump starters are particularly useful for emergencies, such as when your car battery dies unexpectedly and there are no other vehicles around to give you a jump-start, or when you need to charge your electronic devices while away from traditional power sources.
Replacing the Third Brake Light Bulbs
zhlédnutí 662Před 4 měsíci
This video shows how to replace a third brake light bulb.
Replacing the Fog Lights/Lamps with Dual Color LED Bulb
zhlédnutí 643Před 5 měsíci
This video shows how to replace fog lamps/lights. Removing the front bumper: czcams.com/video/jkbTlDKp1TM/video.html
Fix Broken Hazard Light and Turn Signal Lights | Corroded Flasher Relay
zhlédnutí 1,1KPřed 5 měsíci
This video shows how to clean a corroded flasher relay.
How to Remove and Install the Front Bumper | Suzuki Every Wagon
zhlédnutí 719Před 5 měsíci
This video shows how to remove and install the front bumper.
Cleaning the A/C System Without Removing the Evaporator and Blower
zhlédnutí 299Před rokem
This video shows how to clean the AC System of a car using the air conditioner cleaning agent.
Clockspring Repair and Installation | Fix No Horn Problem
zhlédnutí 15KPřed rokem
This video shows how to repair and install a horn clockspring. I don't have a replacement yet so I tried to fix it. NOTE: - check the horn fuse first before attempting to disassemble the clockspring - the clockspring in this unit is used only for the horn TIMESTAMPS: 0:07 Removing the clockspring 2:02 Repairing the clockspring 6:47 Installing the clockspring *sorry for the audio
Spare Tire Removing and Installing
zhlédnutí 10KPřed rokem
This video is for those who do not know how to remove and install a spare tire on their unit.
A/C Cabin Filter DIY
zhlédnutí 1,8KPřed rokem
This video is for units that don't have a cabin filter installed on their A/C system. This is just an idea, you can modify it. The cabin air filter keeps dust and dirt from entering the HVAC system of your car. It can also extend the lifespan of your HVAC system. MATERIALS: - welded wire - a/c filter
Chassis Number Location
zhlédnutí 94Před rokem
Sa video na ito, makikita kung saan nakalagay ang chassis number.
How to Install and Remove Fan Belts?
zhlédnutí 167Před rokem
Makikita sa video na ito kung paano maglagay at magtanggal ng fan belts.
Noise When Braking | A Loose Brake Caliper Sliding Pin
zhlédnutí 8KPřed rokem
Noise When Braking | A Loose Brake Caliper Sliding Pin
Thank You for 1,000 | A Timeline of 1K Subscribers
zhlédnutí 53Před rokem
Thank You for 1,000 | A Timeline of 1K Subscribers
Keyless Entry System Installation (Detailed Version)
zhlédnutí 77KPřed rokem
Keyless Entry System Installation (Detailed Version)
IAC Valve Resistance Testing Using Ohmmeter
zhlédnutí 43KPřed rokem
IAC Valve Resistance Testing Using Ohmmeter
Steering Rack Preload Adjustment | Rack Play and Clunk
zhlédnutí 113KPřed rokem
Steering Rack Preload Adjustment | Rack Play and Clunk
Stuck IAC Valve | High RPM, Idle Drops and Engine Vibrates When A/C is ON
zhlédnutí 8KPřed rokem
Stuck IAC Valve | High RPM, Idle Drops and Engine Vibrates When A/C is ON
Connecting the Seat Belt Wire and Switching the Function From Right to Left (Detailed Version)
zhlédnutí 1,3KPřed rokem
Connecting the Seat Belt Wire and Switching the Function From Right to Left (Detailed Version)
How to View the Released Date of a Car?
zhlédnutí 309Před rokem
How to View the Released Date of a Car?
Cleaning the PCV Valve (Positive Crankcase Ventilation)
zhlédnutí 2,2KPřed rokem
Cleaning the PCV Valve (Positive Crankcase Ventilation)
How to Adjust Idle Air Control (IAC) Valve
zhlédnutí 95KPřed rokem
How to Adjust Idle Air Control (IAC) Valve
MAP Sensor Testing Using a Multimeter (Detailed Version)
zhlédnutí 495KPřed rokem
MAP Sensor Testing Using a Multimeter (Detailed Version)
MAP Sensor Cleaning (Manifold Absolute Pressure Sensor)
zhlédnutí 12KPřed rokem
MAP Sensor Cleaning (Manifold Absolute Pressure Sensor)
Pag naliko ako kaliwa or kanan may clunking possible maluwag lang po ba talaga?
Sir meron ako nabili na central lock with keyless pero yung for signal light niya isang wire lang. So if mag signal ako sa left sasabay din ang right. Ano gagawin ko po?
Kailangan mo ng dalawang diode, isa sa left signal light wire at isa sa right signal light wire.
@@da64wdiy salamat sir. Ano code ng diode at ilang amperes?
1N5408 3 amps
Thank you so much for the informative video,sir may i know what kind of OBD scanner you are using?tnx
It is ELM327 OBD2 Bluetooth/WIFI V1.5
@@da64wdiy thank you so much sir.
more.videos
Pok pok or press? Same lang yan?
Kapag di makuha sa pukpuk, press ang kailangan.
Looks to eeasy
Where is your shop contact number
Now that's a well explained example
Anong pinipihit mo diyan sa wire connector? Hahaha
Pinipihit po talaga ang wire socket upang ma-adjust ang idle speed.
Very nice 👍
Great video! Just what i was looking for. May i suggest turning your pliers the other way around to where the lower jaw is the bottom pressure application point on the nut rather than the top. For instance, when loosening (counter-clockwise) and tightening (clockwise) the lower jaw should always be leading the turn (being the shorter jaw applying pressure) and the upper jaw is always lagging the turn (being the longer jaw as the grabbing point). Just some constructive criticism - food for thought.
Ask lang po ano po bulb size ng sa reverse brake light po ng DA64W ?
W16W po.
what battery do you use for the fob? mine is kinda finicky when clicking it. sometimes it locks but mostly not. i noticed yiur fob led is blue but mine is red. maybe its a battery issue
My key fob uses 2x CR2016 batteries. The finicky behavior you're experiencing might be due to a low battery. Replacing it with new batteries might resolve the issue. The difference in LED color could be due to a variation in the fob design, but it shouldn't affect functionality.
For Lexus ES350 / Toyota Camry adjustment I used 44771 M16-2.00 Metric Hex Coupling Nut
Dol naa ky tutorial sa da17 keyless entry?. Saon pag top?
Di ko po alam kung same lang ba ng wirings ang da64 at da17. Pwede naman basta't may central-locking ang unit.
May naririnig po ako ganyang ingay pero pag mainit na po makina at nirerev nawawala po ano kaya ang possible na sira ?
Upang malaman kung ano ang sanhi ng ingay, maaring tanggalin ang serpentine belt at paandarin ang makina. Kung hindi mawala ang ingay, maaring ang crankshaft pulley ay may sira. Kung nawala ang ingay, maaring ang problema ay nasa tensioner bearing, water pump, alternator, o compressor. Isa-isahin ang pag-alog at pag-ikot sa mga ito; kung may kakaibang tunog, iyon na ang sira.
What bar map sensor is that? My 3bar map sensor at idle only 0.5volt
Boss da63t 4x4 unit ko , tanggalin kona sana ang cv joint nya ayaw talaga makalas , pinokpok kona . Ayaw talaga
Oo mahirap yan.
balak ko papalit hub bearing fortuner 2010 boss tanong ko lang po ano mas ok gamitin ung with abs or w/o abs?
Kung ang Fortuner 2010 mo ay may ABS, mas mainam na gumamit ka ng hub bearing na may ABS sensor. Kung wala namang ABS, pwede kang gumamit ng hub bearing na walang ABS sensor. Kapag ginamit mo ang hub bearing na walang ABS sensor sa sasakyan na may ABS, maaaring magkaroon ng problema sa braking system.
@@da64wdiy salamat boss
is it possible to install keyless entry on a manual car
Could you clarify whether you mean a car with a manual transmission or a car with manual door locks? For Manual Transmission: Keyless entry systems can be installed on cars with manual transmissions without any issues. The installation process is similar to that for automatic cars. For Manual Door Locks: If your car has manual door locks, it might require additional work to convert to an electronic locking system before installing a keyless entry system. This may involve installing actuators in the doors to enable remote locking and unlocking.
Back?
Ano pong sasskyan iyan?
Suzuki Every Wagon
panu ibalik yan sobrang hirap pag hnd stock mags
Thank you! Very straight to the point and helpful :)
Very useful Thanks
Ačiū
Sir. Ano po size ng bushing ? May small at big size po sa shopee kasi. Salamat
Small po.
What car?
Can be applied to any vehicle.
Walang check engine boss.
Wala po.
Sir. Same unit tayp da64w, kaso pag nka on yong aircon nagvibrate kapag mahina yong katakbo. Minsa mamatay yong kapag pag-pahon. Nalinis kuna. Kung nakapark ok nman sya.anong dapat kung gawin?
Try mo e-check ang ignition coil. Kung naka-idle ay ok lang pero kapag tumatakbo o paahon ay walang lakas.
Kalo yang pin nya ada 6 bagaimana cara nya om?
What if there is water droplet at exhaust pipe also with white smoke during start of the engine? But after 30min of using the car its gone
If the white smoke disappears after a few minutes, it is likely due to water condensation in the exhaust system, which is common and usually harmless. However, if the white smoke persists beyond a few minutes, it indicates a potential problem, such as a coolant leak into the engine.
Boss anu twag jn mag order po Sana Ako pang hi ace cumuter
sir ung sakin tumatabingi po sa ang manibela, pinatuwid qna po pero bumabalik parin tabingi. yan po ba ung inaadjust?
Hindi po yan ang inaadjust. Baka po hindi naka-align ang tire nyo kaya tumatabingi ang manebela. Tie rod po ang inaadjust pag ganun.
Same boss. Lumilipat left-to-right right-to-left. Tuwid naman takbo ng auto ko.
May nakita na po kayo solution boss? Napagawa nyo na po?
Gumagalaw ung rack boss pag nilalaro mo ung manibela.Bushing daw boss ng rack ang papalalitan
@@renatoburaga4748 Oo, pweding sira ang bushing nyan.
Hello sir. Is possible for more than a year car Toyota Vios tensioner bearing got damage. Same that sound
Yes, it is possible.
Hi, i have a problem that flashing air bag and horn toots when I press cruise control on, my car nissan nv200 mod 2012, thank you
You might try changing the clockspring in your steering wheel. It's a common cause of issues like a flashing airbag light and the horn sounding when pressing the cruise control.
Honestly good video got a cat that likes to help to. Video makes sense
HELLO I HAVE A 1998 KIA SPORTAGE AT COLD START UP THE CAR REVS TOO HIGH AT 4,000 RPMS..SOMEONE ON HERE SAID IF U DISCONNECT THE IAC VALVE HARNESS, AND IF THE RPMS CHANGE, THAT IT MEANS THE IAC VALVE IS OK?? DO U KNOW IF THAT IS TRUE> AS WHEN I DISCONNECT THE HARNESS THE RPMS DROP TO NORMAL 850 RPMS VERSES 4,000 RPMS when harness connected..please advise..thanks
Hello! If disconnecting the IAC valve harness causes the RPMs to drop to a normal level, it suggests that the IAC valve might be functioning but could be receiving incorrect signals or stuck open. This high RPM issue could be due to a faulty IAC valve. It might be a good idea to clean or replace the IAC valve.
Sir can you show us how to replace thermostat for da64
Sir, maybe some other time.
need to play this at 2X speed.
Salamt boss.
Boss ang fog lamp dali ra ilisan
Madali lang, may video din po tayo czcams.com/video/nm4ljqvjIQA/video.html
Toyota yaris 2016 same system
Definitely a man video! No acting, telling stories of the wife going to the grocery store! Excellent video
I know this is an old video but hopefully someone will respond. I did the test just like shown and everything is correct until I test the resistance between the positive and communication lines. I am only getting .44 instead of 1.2. this is a brand new iacv so I do t think that's the problem. Would this mean that I need a new ecm?
Glad I don't need to rent a cat for this job... Excellent video! Many thanks! I believe this is causing a loud CLUMP noise when I turn my wheels to far right... It looks like two metal pieces jumping or clashing... I might be a pinion tooth sliding and jumping over the rack teeth... It would sound EXACTLY like what I am having on my Jeep Grand Cherokee 2006. Thanks a lot!
What size of 5point screw did you used?
I’m uncertain about the exact size of the 5-point screw. My set is without a label.
S2 T20 or ST20 na security torx na 5 lobes or hex torx 5 lobes type of screw dtiver
@@seälańdęr70 S2 torx
I did not understand anything..video and subtitles very fast and step very fast..😡
No talking please
Make sure you regrease the bearing after cleaning... If not, after some time driving it, the bearing will shot