Video

Why this Sad music ??😡😡😡

Nice idea for the solder reservoir.😊

Какая температура впаивания и выпайки?

Sometimes the problem. with a charging port is the small board or ribbon it's attached to and this would be pointless.

what was the reason you did 280-300 when you were putting it back?

Super

Sir what kind of glue are you using?

Thanks for this information! What type of glue you are using?

this method not good , type c connector will be warping , beware

EMMC/UFS Stock on hand, pls go to my page. THGJFLT1E45BATP 256G THGJFLT2E46BATP 512G THGJFLT3E86BATU 1TB SDINFDO4-128G SDINFDO2-256G NCEMASLD-128G MT62F1536M64D8CL-026 WT:B MT62F1536M64D8CL-023 WT:B

Price ?

You are right because there either laptops or mobile phones but a little dose of low melt falls out all good been a tech 40yrs

vry old methed and ehni loca glue de jarorat he nhi pehndi frem wich rako pehla fir lagao

So beautiful sir❤

Ok, its called a soldering iron. Also, olease look up a video about how to properly maintain the tip. Soldering irons must be "tinned" in order to work well. It makes soldering much easier! Id suggest looking up some videos in this because it really does make a big difference. Then, use a small damp sponge or wet hand towel or rag to rub the tip against to clean it between soldering steps, this keeps the gunk from building up and also removes the oxidization layer. Thus all will also extend the life if the tip by years. Be careful of adjacent components. You niked the surface mounts abouve this charge port. Easy to brick the pcb this way.

you broken a lot of pads! and make this video for click bite! SHAME!

350°??? are you sure??

Doesn't help if you don't explain what your doing to people who have never done this before

Is he using flux to remove old soldering material?

Thank you so much❤

air kitna hai

Air kitna h

Can I ask what cause this to happen please… ❤

and the green stuff use on the surface

what's the name of that brown stuff use in cleaning panel

Muchisimas gracias . . Por el aporte . Exelente sirvio de 10 . . Todo

Well done

you really make the subjects you cover come alive!

Air

Says fast charging but its at cable charging speed! Changed the cable, same as! Oh well, at least its charging!

Do you know what that piece on the left would be called kinda looks like a switch that can be pushed up and down ... I need to replace those on my phone and I can't figure out what there called

Thanks sir

Helpful ❤

please provide your ph number

Sir ji kon sa fone hai ye iska modal bataiye

temp a 350 no desoder afther 10 min

No temperatura. No air.

naja, nicht schlecht, aber ein pad wurde beim entfernen des IC leider nicht wieder hergestellt😐

Working perfectly, thanks!

What do you call them, I can't find them on AliExpress

He already removed ic or multiple time removed id bcz there no ic paste 😊 i do this so many times sucessfully

This is a common problem with the a10s. I sell phones and the last time couple time i saw this issue it was with the A10s probably get solder joint crack based on the video.

Repair ka charge kitna h😢❤

Worked for me, thanks bro

Ambon ambunlang asawa😊

Thank you .... Done successfully .

Sir iske kitne charges lete ho

hello guys, i have a hp spectre laptop but the problem with it its not charging the usb c port is very lose, so i called the call centre they said they should change the whole motherboard because it is directly connected, so i was searching for a usb module so that i can solder it but i have a doubt that can we use any usb module or there should specific ones? if there is any specific ones please let me know

It is not easy but with training we can achieve it.

Perfect and good work👍🏼🌹😊