Video

Can you programme the transponder without a key blade?

PANO po ba maka order Ng pyesa Ng foton trasvant Ng PO191 at mag Kano po

I have a Hyundai Getz. I had a problem with not starting. The engine management light was on. All I did was undo the 2 screws that hold in the coill around the ignition. Hey presto not had a problem since. 2 years no problems.

Hi,could You please Tell me If You know what resistance should the Ford focus MK2 .5 1.8 tdci presure regulator have?The pump îs siemens.

Well-done You are so clever, you could find and solve the car's problems easily .

Where is the inhibitor switch located on a 2012 Hyundai Genesis sedan?

Good job

No ignition in my 2015 smart key

Sir, one question if i may plz. my friend's Hyundai Sonata YF smart key with SSB and fob holder and when fob inside the car SSB doesn't respond at all unless he put the fob inside fob holder and then car cranks and start and run OK. so, i've changed for him 3V battery (which is even 3,3V) more than enough, even couple of times and defferent brands, nothing changed, i did diagnoctic and checked all antennas all good,all active. i wonder what else could it be a reason of that failure? may be RF reciever shorted to ground or anything? no fault codes during diagnostic with Thinktool SE and Expert 195. just don't want to disassemble all dash apart for electrical check-up before make sure there no problem outside of RF receiver and SKM or PDM or FOB holder. any ideas or suggestions what is wrong? may be reprogramming a fob mind help? thank you in advance

🎉

What... All you have to do is pull the bottom hose and see if there is suction ,leave electric hooked up and check for a vacuum

Good morning senior, thanks for the knowledge you have provided, please is there different ways to remove cvvd camshaft without the special tool

all my solenoids besides shift control read 6 ohm, shift control reads 11 is that normal for all the others to read 6 ohms? i thought the number should be 5.1?

2015 genesis coupe b1602 and I forgot the other code but smarta no response car was in a accident and passenger side on the windshield was broken to allow water and then I pulled the smart key module it was corroded I can start car only with key in the holder and then dies 4 seconds after it starts then immobilizer light is on then no start just crank also door handle unlock botton on the outside doesn’t work I’ve come down to where I need to replace the module any input?

Bro isnt the same video available from another channel? I guess its automotive diagnostics or something. Same content ditto. No change. Not sure if you copied from him or if he copied from you. czcams.com/video/vaTp3inTMdU/video.htmlfeature=shared

ارادت مند مهندس

Perfect

Where is the eps motor

You might be interested in watching the following video too: How to Test Ignition Coils | Ignition Coil, Wiring & ECM Internal Diagnosis czcams.com/video/UlFT79Ulty8/video.html

Neat system, but the pisser is that the seal where the actuated part enters the manifold has created a vacuum leak on my car. Hyundai does NOT have a seal kit for these, if fact they barely acknowledge that that intake system exists on a 2006 Tucson. Now I'm stuck with removing the manifold to see if I can find a replacement for the seals.

On mine there is a bolt on the right right about 20cm above the fog light. Any recommendation on how to remove this?

hello thank you for your videos hopefully you can help me I have a 2017 kia forte5 ex with what i believe is a A6GF1-2 transmission. I pulled the valve body and I'm trying to measure the solenoids resistance to test them but I can't find info as to what they are and what the read should be. What solenoids do what. The issues I had where with 4th and some times 6th both only if going up a mountain. the trans on the inside is completely new looking all the screens on the solenoids very clean. any advise or links to diagrams or thoughts would be appreciated. Thank you for your time

Whats the tool

can I download the carman i100 program myself to do this?

Hy! ive tried diagnosing a Sorento 2017 for Ac problems but i cant find the Ac unit on the diagnostics tools. is there a way to connect to this unit to do a diagnose? or just manual diagnosing procedure?

how to check antenna resistance?

Recommended every 60,000 miles on my Kia Rio. I wonder how much this costs at a shop?

Hello, when a measurement is made to a sensor, is the procedure the same for a gasoline car as for a diesel car?

Hi, How to get the logs from the ECU regarding engine and turbo? Thank you in advance!

good job

Very helpful. Thank you for posting!

Speak slower next time, the car wont go anywhere.

❤️❤️❤️

Love the videos! Very informative and clear to understand! Thank you for your efforts in teaching us!!

You might be interested in watching the following video too: Starting System Explained | Starter Solenoid, Relay, Inhibitor Switch, Wiring Diagram czcams.com/video/-UHPCJdYxcg/video.html

Hello, I have Kia Picanto 1.1 CRDi, the car wont start, when I put the key in the ignition and start, Nothing happends, the motorn dont even go around, its just a click sound, I get the immobilizer lamp on, but the car wont start anyway, I diagnosted the car with my computer ( Autocom) i got the faulty code immobilizer, I checked everything like you and everything looked good, when i put in the 1st gear and push the car, then it starts, my question to you, is it the immobilizer or the startmotor?

You saved me from a whole lot of grief and throwing tools.

I need yours contact number

Very useful video, thank you

Thanks a lot. I learned a lot

عالی هستی مهندس دست مریزاد❤❤

🥰🥰🥰

Thanks man

Grasias

Thanks for the video I wish you the best

❤❤❤❤❤