Video

So beautiful!

This will make your kayak even more heavy and probably with fully loaded with equipment your exceeding the max weight required limit

Hi, We don't see much, but is it possible you have clubbed fingers? If so, I'd suggest visiting a clinic justi n case. If I'm mistaken, I want to apologize and please disregard my message...

I have allpowers r600 v2 with quiet fan and it is great. Charging curve for all so you can see how much power is needed to each % . it was measured from electric plug. 0 % - 1% less than 100 wat for few seconds 2% 127 wat 3% 160 wat 4% 199 wat 5% 240 wat 6% 273 wat 7% 304 wat 8% 342 wat 9% 368 wat 10 % - 80% full rapid charge 413-419 wat 81% 390 wat 82% 356 wat 83% 327 wat 84% 298 wat 85% 268 wat 86% 239 wat 87% 208 wat 88% 178 wat 89% 149 wat 90% 119 wat 91% 114 wat 92% 107 wat 93% 100 wat 94% 94 wat 95% 90 wat 96 % - 100% 88 - 86 - 84 wat

8 years have passed and my AUKEY is still alive

Do you still recommend the EGO a year later?

Is there a filter.

Merci Pat, super bon.

How much was your hourly pay?

I like it. I like the firm padding. I use my glutes by straightening my leg to catapult my leg backwards with my femur on the saddle as a fulcrum (like 70s and 80s riders) and so the padding needs to be firm. The padding on my old Bontrager saddle was slightly firmer.

I appreciate this video. Im getting the Minn Kota 30 lb thrust motor for my 110.

We bought a GoLabs DL300 and it worked for ~4 charge cycles, started throwing error codes and would discharge when not even on. I tracked discharge with the unit off (turning on only to read remaining charge) and for 2 days it was fine but then went to zero in the space of 10 minutes. I charged it one more time and I was able to recreate it but then it would not charge and I got error codes till the battery fully ran out. We contacted 'support' and got nothing back. I have worked in electronics for decades and so realizing we were on our own, I took it apart and found a fried U11 on the main board. It wasn't dropped or mishandled and so my conclusion with other problems I am seeing reported on CZcams is that the components, assembly or both are poor quality. I would avoid this product.

I took my DeWalt 2024 model back which cost me 700 dollars and it just didn't have the power there is a connection in the base where the battery plugs into on the lawn mower. Both batteries fully charged. I also switched batteries around in the base and the left side had power and the ride side didn't and you could even tell when it lights up the battery grid on the handle bar and same thing no power. For 700 dollars the Electric Lawnmower it should be able to run circles on the lawn. I could understand if it was some cheap off brand lawn mower but its a DeWalt which is supposed to be a great brand and and live up to its name. I got my lawnmower from the Home Depot which is 67 miles from where i live and i am not going to take it back and get another one and have that same defect happen to me so i bought a new Honda Gas Mower for the same price. The older electric DeWalt's models look like they actually work but I really am not impressed with DeWalt electric mowers.

Jesus loves you God bless

You're awesome ❤

Dude clean the dust before making the video. You kidding?

Cant you just flip the seat to the raised position and sit sideways to get to the motor?

So I’m buying this same kayak and was wondering with how you have your trolling motor side mounted, do you have to artist your steering in order for you to go straight if that makes sense?

What oil using this kobalt chainsaw

4:04 Could you please tell me how to reset the maximum and minimum readings in the "memory" column of this thermometer?

thank you for this! tired of tik tok “reviews” , i needed an in depth one(:

I think you are not understanding that this is for Small stuff that draw low power. Not for a Blender 😂

You should never have your hands near a blade.

You need a better workstation and clamps, what your doing is dangerous, no stability at all.

I see a basic problem with this setup. The way it’s placed, the motor/shaft/prop must move forward to raise. For me this is bass ackwards. I want my motor to lift up to the rear, so I can leave it unlocked in shallow water offering some protection to the prop and motor if an object is hit.

The comments about not clamping the wood harder against the shoe = stupid. When you go into the woods to cut wood, there are no clamps, and stuff bounces around everywhere. Great comparison, thank you!!

I bought an EGO 2135SP and it’s fantastic! I used my Lawnboy SilverPro Duraforce for 21 years and the EGO outperforms it! 👍🏻✌🏻

Handy tips for when you get accosted by a gang of militant coconuts👍

I use a 100 watt swarey daisy chained with the renogy eflex 100 watt and the bluetti ac2a solar generator and i can charge it in 20 minutes

Where can i get one of these

Thank you for the review. Transitioning from gas mower to electric mower.

where can you find the adapter for casseroles for this model (the round thing that connects with the hose) ? or it comes with the casserole?

Great experiment

What about reversing the 4 mount screws and use wing nuts on the top for easy removal?

Please have this upload this vedeo .very interesting

So this was clearly biased. First of all, Dewalts screw was clearly lower than rigid. Rigid caught up. You also used Dewalt in your primary dominant hand. Biased review.

Is the renogy waterproof

Sorry mate, but you have to clamb your piece that you want to cut, securerly. All of your saw morion is going to waste!

😴

Does the Renogy come with the cable?

This is not even close to a fair comparison: 56V vs 18V, really? EGO is great but cost twice as much as this Ryobi model.

why you don't try wifi 6ghz? which is the main purpose of 4kmax

Bagging issue is probably due to blade type. A high lift blade always creates more suction. You also said that you were running the DeWalt at the low rpm setting. So there's that.

from what side you make order ?

Try re binding it,I thought the same thing,fixed by putting new battery in controller

How is the wobble (run out) on this? Because I recall the centrofix was quite wobbly.

Flat, not level. Big difference.

Im not Ridgid defender, I'm actually looking into what brand to get into for me. Been watching a ton of videos and its weird, every person that tests drills and impacts always leans towards the one they use in their right hand. Just watched another vid where the Rigid was in his right hand and he liked it over the Dewalt.

Just bought this set. Couldn't get box in trunk of car. THIS video showed me how to remove the handle, fits in trunk of Chrysler 300c just fine! Love the internet! Great review! Thanks for the info!

just bought this scooter! thanks for the video, it was very helpful.