Video

It realy works! 🎉 Thank you!

I have the same one bought from Bulgaria. Great Soviet artefacts!

Dime qué tan bueno es este equipo?

Nechtělo nejdříve přivést napajení na DC motor se zkouškou jeho funkce?

for a busy road, in a cold climate where all cars will have their windows shut, this is a good idea.

yes i wanted a bell that needs charging and can develop electrical problems

😢

dude, just by cheap chineese wattmeter instead of this wireless tester

do you have for 25/30A

Do you know how to change fuse for AC inverter of where is it? It would be extremely helpful if you can tell me.

Why did you bother to sit here and say "I can do this" for 20 minutes and not explain ANYTHING on how to do it? This is incredibly frustrating. I'm a network engineer and trying to find out how to set this up and understand how it works. And all you can find on things like this are useless things saying you can do it for 20 minutes with zero help or guidance. I'm already familiar with networking and how this should be working as a gateway and it won't even send an ARP request to anything in the route including the radio IP range. Furthermore it's a bit confusing as you get a 192.168.10.0/24 network resented to the interface but can't reach this mysterious internal radio network associated with ARS or whatever it is. Is the only purpose of this video to show that you know how it works and nobody else does? You could have accomplished that in 30 seconds. I will figure it out but not from this video at all! Thanks.

What accessories are available for Entel DX485?

Thank you you saved me opening mine to see what is in the box. So the brains is in the USB plug

Mine is not charging but battery is fine and it still works. Any solution to fix harger? Or how to charge it with wires and not wirelessly?

Thank you so much

Hi sir iam having a sony wf xm3 one side of the buds is having a high pitch noise can you please repair it for me i have tried cleaning it as u shown in ur video

where can I find batteries? do yu have a link

Thank you. Very helpful.

This guy sounds like Borat very nice 😂

I like the Entel and Tait gear. The last DX / HX series Entel that I played with did not have the ability to show frequency on the display, so this must be a more recent firmware version. Look for a Tait TP300 series - You will not BELIEVE how rugged they feel!

Hi this might be a silly question, but I have a Sony Handycam DCR TRV520 that has a firewire port, I also have a ton of Sony 8mm tapes (does not say Hi8 or Digital 8 on them). My question is if I can transfer them using this firewire technique? Thanks in advanced!!

Hi there, thanks so much for the video. May I ask - I have many tapes which were recorded with a Canon HI 8 Camcorder. Would it also work to digitalize them with a Sony Camcorder like yours or does it have to be the exact model with which the tapes had been recorded?

Forty bux for two CR123 cells. Not even rechargeable. What a complete, total ripoff. Those scumbags should be ashamed.

Perfect 😎

Very good! Congratulations! Can you post the link where you bought the XT60 to 8mm DELL cable! I can't find it! The ones for sale are the 7090 or 8020 without the connection part which doesn't connect/enter the 8mm charging port of the GZ.

nice one 😎😎😎

can it be modified to use UHP 120W bulbs? Will it get so hot that it melts?

Сам вскрывал эти батареи- очень тяжело вскрыть без повреждений! Учитывая все проблемы с ремонтом лучше купить оригинал или аналог! Поверте.! Ели на батарейке 1.7 вольта то это кирпич без возможности восстановления 100%

Instead of motor, also check the Rz27889 motor control chip! Mine was blown-up

I have a Compaq Presario 5170 with only the original Windows 98SE Recovery Disc install and when trying to install receive error, "The Native USB disk driver for Windows 98SE ver 3.3 package is not compatible with the version of Windows you are running".

Error #1057

Great job. Thanks for sharing

urgh, same happened to my baseus (30ah version) right now. annoying - i was expecting a more premium product.

On my machine (same model) I had to hold only the spin button without start button. Otherwise it worked great. Thank you!

Dusting of fan? Bro... you need to remove those pillows

Why so aggressive opening such a fragile replacement part?!!

Thanks, it worked! But the small screws don't need to be removed. 🙂 Maybe Yeti 500X Reset helps aswell: Press and hold the units and info button.

Wow, a lot of parts used to find a simple fault, though it was in the worst place possible! Well done on finding that fault. It is one of those faults that end up in hair being pulled out !! 🤔 🙄 Thanks for showing us it.

super helpful was really scared about there being something wrong with my camera but yet such a simple fix!

thank you for the video but what kind of proper size of chuck insert have you request to aliexpress ?

Hi. Do you, by any chance have the latest fimware image for the dat 40 drive? File name should be LTT_HP_C5683A_YU8B.frm. I cannot update mine through HP L&TT.

Hi, if the built in battery is old and worn out, it there a battery replacement? Or what to do?

I use one on my prc 77 and works very well

Where did you buy this ant -129?

The slider on my coil is very hard to move up and down. Is there a way to make this easier?