![Piotr S](/img/default-banner.jpg)
- 130
- 215 008
Piotr S
Registrace 18. 11. 2007
Video
Barrel + action (308Win)
zhlédnutí 90Před dnem
Miejsce od którego chciałbym aby zaczęło się ryflowanie lufy. Z uwagi aby zmniejszyć wagę lufy. Cytując portalem strzeleckim - Kanelowanie lufy, znane również jako ryflowanie, to proces, w którym na zewnętrznej powierzchni lufy karabinowej frezuje się podłużne rowki zwane kanelami. Choć na pierwszy rzut oka może się wydawać, że jest to zabieg czysto estetyczny, kanelowanie ma również swoje prak...
308Win rifle LOP - Measure the Length of Your Pull for a Rifle
zhlédnutí 104Před 21 dnem
Measure the Length of Your Pull for a Rifle The length of pull (LOP) is the distance between the center of the trigger and the back center of the butt plate or recoil pad. A proper LOP is necessary to ensure the shooter can shoulder the weapon comfortably and it also puts the head and eye into the correct position to use the sights or scope. Keep in mind that you must follow all rules and regul...
AR10 6.5SLR and Bolt 308WIN, Headspace Go Gauge, No Go Gauge, brass cases headspace dimension.
zhlédnutí 120Před měsícem
AR10 6.5SLR and Bolt 308WIN, Headspace Go Gauge, No Go Gauge, brass cases headspace dimension.
416 Barrett CASE ROLLER HD (HEAVY DUTY)
zhlédnutí 198Před 2 měsíci
The GMB Case Roller HD is a machine that restores proper case diameter by removing the bulge from cases, while also resizing the rim of the case for optimal performance. The process is called roll sizing or roll-sizing, and shooters and reloaders refer to the machines as a case roller, roll sizer, or rollsizer. Additionally, the machine is designed to consistently resize the cases with less str...
416 Barrett, Load Data Powder - Reloading
zhlédnutí 112Před 3 měsíci
416 Barrett, Load Data Powder - Reloading
416 Barrett, Maximum Case Capacity, overflow Grains H2O
zhlédnutí 85Před 3 měsíci
416 Barrett, Maximum Case Capacity, overflow Grains H2O
Bullet Tipping Die, Erik Cortina Precision Bullet Flow System for Pointing Bullets - Dillon 750
zhlédnutí 163Před 3 měsíci
Bullet Tipping Die The Bullet Tipping Die is designed to improve ballistic coefficient, accuracy and consistency. Use with a wide variety of bullet types and calibers.
AMP annealing brass + AMP MATE Revised + Dillon
zhlédnutí 206Před rokem
AMP annealing brass AMP MATE Revised Dillon
AUTOTRICKLER V3 FOR SARTORIUS, AUTOTRICKLER V4 FOR A&D, SUPER TRICKLER ST101 gen2 + FZ-120i
zhlédnutí 525Před rokem
AUTOTRICKLER V3 FOR SARTORIUS, AUTOTRICKLER V4 FOR A&D, SUPER TRICKLER ST101 gen2 FZ-120i
AutoTrickler V4 A&D scale, AutoTrickler V3 SARTORIUS scale, RCBS Matchmaster Powder Dispenser
zhlédnutí 749Před 2 lety
AutoTrickler V4 A&D scale, AutoTrickler V3 SARTORIUS scale, RCBS Matchmaster Powder Dispenser
30BR Brass Neck Turned - Pumpkin Don Nielsen. The 30BR cartridge is formed by necking-up 6BR.
zhlédnutí 705Před 2 lety
30BR Brass Neck Turned - Pumpkin Don Nielsen. The 30BR cartridge is formed by necking-up 6BR.
Tuner Barrel 22LR - Barrel tuner made by Menke gun Anschutz 2013 Shilen barrel.
zhlédnutí 4,7KPřed 2 lety
Tuner Barrel 22LR - Barrel tuner made by Menke gun Anschutz 2013 Shilen barrel.
preparation of brass in the 30BR caliber from 6BR Lapua brass
zhlédnutí 3,7KPřed 2 lety
preparation of brass in the 30BR caliber from 6BR Lapua brass
Weight correction in the caliber 284Win
zhlédnutí 489Před 2 lety
Weight correction in the caliber 284Win
Preparation for the competition LongShot 2021
zhlédnutí 1,1KPřed 2 lety
Preparation for the competition LongShot 2021
Dillon Xl 750 autodrive Mark7 swage brass
zhlédnutí 1,4KPřed 2 lety
Dillon Xl 750 autodrive Mark7 swage brass
RCBS Matchmaster Powder Dispenser - 98941
zhlédnutí 430Před 2 lety
RCBS Matchmaster Powder Dispenser - 98941
It would be helpful if you explained what you are doing.
I would also like to know where to get one
Or at least what brand it is
Hi what is the stage you are doing with the brass at 4-10 cheers
lapua scales have different neck and shoulder thicknesses. When you convert 6BR shells to 30BR, you replace part of the shell shoulders with the neck. Then a donats is formed, I remove it with a reamer.
@@Popojub thank you for the reply keep up the good work sir
If you do this, do you turn your brass less if you gonna neck turn?
You make this after shoot , or make full bushing and after that you make this ?
What was the tool in the end of the cartridge case ?
Wonder how you configure/set your dillion case feeder with large brass plate to work smoothly? If I put too many like 40-50 308win brass in there, sometime it gets stuck(most likely because of the weight of the brass press the plate at the lower or lowest point), so I have to manually shuffle the brass a bit to let it going. Couldn't comment on your AMP+Mate+Dillion video, so have to ask it here. Thanks in advance.
Sorting bullets will help you for consistancy, if your resizing is consistant (.001 or more to bump cartridge to cartridge and you will not get a perfect seating). I have the same Turban press, they are awesome, but for seat bullets I use Le Wilson dies, with that you can control the seating pression, with K&M pack force (or 21st century press, or AMP press), for consistancy that work really better than others systems, don't need to reseat some bullets, all are perfect if all variables are also perfect. I tell you it because like me I see than you want the perfection, if you try you will see.
Widzę że skoro sypiesz z 3 różnych urządzeń w ta samą partie to każdy z nich musi ważyć dokładnie tak samo.
Wszystkie wagi mają wbudowaną wewnętrzną kalibrację. W greinach, Sartorius wyświetla z dokładnością 0,001 a A&D 0,01 . Ostatnie miejsce po przecinku zmienia się co 2 ( czyli nie ma nieparzystych cyfr). Naważki to ciągła zabawa z +- jedno ziarenko (które teoretycznie waży około 0,02-0,03 GN). Trzy ustrojstwa ale naważki dokładne podobne wzajemnie.
@@Popojub Polecisz może jakiś system naważania do wagi OHAUS (waży do 0,001 gn)?
@@roj_jeferson niestety masz problem, na tę wagę nie ma nic dostępnego. Praktyczne rozwiązania są na wagi A&D, już na santoriusa obecnie nie robią bo sama waga kosztuje tyle ile AutoTrickler czy Supertrickler z wagą A&D. Jedynym rozwiązaniem to sprzedaż wagi OHAUS, kupno wagi A&D oraz jakiegoś rozwiązania na tę wagę. Funkcjonalnością bardziej mi odpowiada AutoTrickler v4 niż SuperTrickler a waga jest taka sama w obu rozwiązaniach. Nie jest to jakaś cudowna waga ale widać w USA dość popularna i względnie cenowo nie za duża. Szybkością działania nic nie przebije wagi santorius ale ile znajdzie się zwolenników zapłacenia dużo większej kwoty za takie rozwiązanie. Na dziś dla mnie wybór by padł na Autotricklera v4 z A&D, względnie najtańsze rozwiązanie, dość przyjemne i bardzo prosta obsługa.
@@Popojub ok, dzięki za odpowiedź
Czemu na dwóch?
Na dwóch prasach? Jeśli pytasz o prasy to zwróć uwagę że na jednej robię, zamocowana matryca Redding-a ale we wszystkich matrycach mam zamontowane śruby mikrometrycznie Mitutoyo. Wygodniejsze, precyzyjne w działaniu, perfekcja. Czyli na jednej prasie składam a na tej prasie po lewej stronie mam zamontowany Redding Instant Indicator z elektronicznym czujnikiem zegarowym. To ustrojstwo usprawnia pomiary, w tym wypadku BTO naszej amunicji, szybsze i łatwiejsze w zastosowaniu.
Hello, which press can recommend TURBAN PRAZIPRESS 120 or TURBAN PRAZIPRESS 140 for me? Thank you.
for caliber 416 Barrett and 50BMG I have the 150 model, for smaller calibers I have the 105 model which is comfortable to use.
Hi. You have a nice set up. I have the same priming unit and I want to get the dillon rf100. What size is that brass on top of the primer tube?
Very nice. Have you made this?
Takie przygotowanie łusek to czysta przyjemność :)
Dzień dobry. Palce takie czarne... gdzie pan znalazł te luski? W dupie?
I recently purchased the Sartorius that replaced the Entris. What do I need to auto powder drop and trickle like your set up?
I recently purchased the Sartorius that replaced the Entris. What do I need to auto powder drop and trickle like your set up?
Siemka Piotr ! Znaczy aby zeskrawac luske do koncowego wymiaru skrawasz ja w sumie po malu ale 3 razy. Pozdro
That's different
Thans for the video , very nice! Could you please give some more info on the setup when neckturning, what type of electro motor is that and what about the quick close collet for the brass ? Thanks ;-)
Panie Piotrze , widać że łuski nie są ośiowe bo jak Pan zakłada uchwyt do toczenia to kołysze się na boki . Ciekaw jestem jaki ma to wpływ na całość naboju . Takie moje spostrzeżenie . Pozdrawiam i zazdroszczę pasji i cierpliwości najbardziej .
Łuski nowe takie są, ale dlatego trzeba przygotować odpowiednio łuskę - powierzchnia wewnętrzna i jej wymiar. Musi być odpowiednia średnica trzpienia w naszym przyrządzie do toczenia oraz odpowiedni wymiar otworu w naszej szyjce w łusce. Uchwyt gdzie mocujemy łuskę dlatego musi być na tyle wahliwy aby te niedogodności niwelował. Dokładność jest duża i powtarzalna mieści się w 0,0001" czyli 0,00254mm. Nie na darmo mówi się że łuski są coraz lepsze po 2-3 krotnym użyciu. Dopiero po odstrzeleniu i formacie one zaczynają być idealne - coraz lepsze.
Why even post a video if you aren’t going to answer questions? Besides that, I personally think your entire video watching you fiddlefuck around is totally lame.
I have a question. Every once in a while I get a kernel bouncing out. I have my dispenser closer to the back of the glass cup. Yours appears to be more in the middle.
It also happens sometimes. You need to limit the kernel falling speed.
@@Popojub I figured as much I'm thinking of getting a Area 419 tube. It has a much smaller opening. Thank you for the reply
Bardzo jestem ciekawy działania tunera, sam robię podobny tylko wymiarowo bardziej jak EC.
Broń dostałem chyba w styczniu 2020 roku. Trochę zawodów pozwoliła mi wygrać, jest fajna (strzelałem konkurencje 100m - 300m, oraz 100m - 200m). W zeszłym roku bawiłem się tym tunerem, działa skupienia możemy ładnie zagęścić. Problem z tunerem Menkego był brak jakiejkolwiek skali na nim. Prędzej narysowałem sobie jakąś skalę pisakiem i tak robiłem regulację. Teraz aby to lepiej i dokładniej zrobić, zrobiłem skalę. Ustawienia muszę zrobić na nowo bo mam dokładniejszą skalę. EC mam również jak i inne, działają.
@@Popojub Dzieki i pozdrawiam.
Witaj. Aż ciężko uwierzyć żeby Menke wypuścił takiego bubla.... chyba ,że były już modyfikacje.
to nie ma nic wspólnego z bublem. System Anschutz 2013, lufa jest wkładana do tego sytemu i zaciskana jak widać trzema śrubami. Lufa była delikatnie odsunięta od systemu, teraz lufa jest włożona na Loctite 620 a śruby przykręcone na Loctite 222 aby się nie odkręciły. Lufę wyczyściłem aby ładnie weszła w swoje miejsce, tak jak Menke to ładnie spasował. Mając wzorniki Go i NOGO mogłem sprawdzić czy teraz jest OK. Wszystko jest teraz dobrze. Może było tak że skręcając wszystko nie docisnął lufy do sytemu, albo delikatnie za słabo była przykręcona i się od sytemu w czasie użytkowania odsunęła. Teraz nic takiego nie powinno nastąpić. Nie dopatrywał bym się bubla w tej broni.
Hi Piotr, I have a 2013 too, the only issue with this model is that when you tighten the barrel with the 3 screws it deforms slightly the bottom of the receiver. If the bottom is not perfectly flat, the receiver isn't in perfect contact with the stock which causes accuracy issues (bad bedding, so inconsistent harmonics). I would not disassemble the barrel unless needed, and do skim bedding after that.
I was doing bedding, in addition, between the system and the stock I put a washer cut from REINZ AFM38.
What press is that?
www.turban-cnc.de/prazipress
What are you using to remove the doughnuts
Whats THE name of that machine?
Hi Piotr. What type of drill is that?
It's not a drill, it's a reamer. I have different diameter reamers. So far, I used the 7.7mm reamer as the first, the second has a diameter of 7.8mm. See if it's enough, I have other reamers 7.82 7.84 7.86
Hi Piotr, how many expander passes does it need from 6mm to 308 ?
three expanders with a diameter of 6.70mm, 7.17mm, 7.82mm. You have to remember that the expander in the turning device must always be 0.02-0.03 mm smaller than the expander which is pushed. 7.82mm and for turning 7.80-7.79mm
For example, Papkin and K&M have a .308 "turning a .307" diameter while others, such as Sinclar, 21st, PMC have a .307 "turning a .306" diameter. There is always this dimensional relationship.
@@Popojub Thank you, this is the perfect cartridge for shooting at 300m. I dont know why we dont see it so much in the shooting ranges, maybe not enough choice for match bullets with such light weight ?
You should repeat this into a continuous loop to make like a 10 hour video. There are millions of 2nd amendment Murrcans that would have this up on their screens all day. Relaxing, therapeutic, maybe help some sleep at night.
И самое что интересное, бабла дохуя, как и у наших, а стреляется хуево так же как и у наших)) а чемпионы мира на коленке заряжают из дозаторов "шли" и все огонь! А А вот тепепь мои американские друзья! Сломыте голову над переводом моего комментария 😉🤣
Hi, I have a question. At what PSI (Air Pressure) does the spindle operate for the automatic tool change? What PSI?
Where is your explanation? It looks like you are using 2 different tools; 1 is a "seater" and one is a "gauge". What is the brand name? What is the model number? What caliber(s) does it measure? What is the cost?
I have the same question. What I can figure out is that he is using a MITUTOYO Absolute Digital Indicator that sells for about 200 dollars and he has added a re-loader part to house the bullet. Try using the RAVEN EYE CUSTOM RIM THICKNESS MEASURING TOOL.
Great video, but I have a question? I have the sartorius cp64, and understand it will work with the auto trickler. With that said what did it take to make the auto trickler work with your sartorius?
I can’t believe he doesn’t give any information on this tool and say nothing. mmmmm
Yeah, what's that about?!?
looks like slow is best
Gratuluje nowego sprzetu !
What model of Sartorius are you using, and did you have to make any modifications?
coś pięknego .
Możesz napisać gdzie to cudo można kupić?
Piotrze co wlałes po ludwiku.
Amoniak (woda amoniakalna) 25%
wodę amoniakalną i płyn do polerowania mosiądzu sz4. IMHO dodawanie amoniaku jest błędem. Zwróć uwagę jak niebieska woda była przy jej wylewaniu z tumblera, to "wypłukana" miedź.
@@tomaszgodek774 Polerowanie metali szlachetnych i kolorowych robię od ponad 40lat
@@Popojub jestem chemikiem do 35 lat. Dalej się licytujemy? Poza tym wyraziłem swoją opinię, a co ktoś robi to mi lotto ;-)
Very nice!! I have the CPS on the way... Still need the RF100 though.. ultimate combo
Is it a Dillon machine or your build ?
WTF ??? What's that, is it your new automated reloading system ??? 😃
Piotr, jak zwykle narzedzia i kosmosu ! :) Pozdro !
Ale bajera! Fajnie robi flip dla tej co jest w denkiem do góry :D
Cześć Piotrze, tak przeglądałem Twój kanał i trafiłem na ten film. Powiedz proszę co robiłeś i w jakim celu?
Sorry że dopiero teraz nie widziałem pytania. Lufa w kalibrze 284Win poprawiam stożek przejścia aby był odpowiedni dla danego rodzaju pocisków. Takie szczegóły aby wszystko ładnie latało.
What stand / microw ball holder is that.Good to see I am not the only one who does a two pass neck turn