Video

I drilled a small hole in the black ink cartridge and filled it with 5ml of black ink. But the yellow light is still on saying low ink. Now what?

Prevents tangling but ur dropping the line under the trail line every second loop!

it worked thank you sooo much! as student living alone this help me unclog my sink without calling anyone.

🤝great work sir

I have tried two walking feet, both have the needle coming down onto the foot 💥😢. Luckily im cautious as i go and not broken the needle. I'm almost giving up hope of finding the correct foot. (Machine has been given full health check.) Singer professional SX low shank. Any suggestions please? 🙏🏻 Thank you.

How do you make it stop saying that there's an error now it doesn't recognize cartridge After I filled it up

Thank you

Thank you! I was always wondering how to play this game without ROB.

I like this idea!!! I wish I'd thought of this. Thank you

I've done the refilling but printer is rejecting it. It says this cartridge has already been used. HELP

Good info in general, but was expecting to see how to wire a GFCI downstream from a another GFCI, and the downstream has load. Can the downstream GFCI trip to protect load, but NOT trip it's upstream line GFCI?

Thank you so so much for this video. It really helped me alooot

This is amazing! A friend was helping me today, and this opened a sink with 6 inches if water in a matter of seconds. I had just ordered a sink plunger from Amazon moments earlier, and I came across this video. I had planned on calling a plumber if the sink plunger failed. Drain openers poured in did nothing in 24 hours. Thank you for sharing this incredible technique.

Thanks, Chris! Good video!

Not sure what I did wrong. I did black and color and my test page came out completely blank :(

thanksssssss

Grate job explaining 👏

Awesome Video I recently visited your CZcams channel and enjoyed your content. However, I noticed that your videos are not ranking well due to some issues. I believe that if these issues are addressed, your videos will rank better. Here are the issues I found with your channel: 1. Video SEO has not been properly done. 2. Videos are not being released on time. 3. The video titles are not optimized. 4. Keyword research has not been done effectively. 5. Video thumbnails are not appealing enough to attract viewers. Solving these issues will help your CZcams channel perform better.

Thanks!

Your looks are so lovable and calm😘 Unclog my heart pleeease

6 ml black ink for cartridge cl-243, 2 ml each color for cl-244 Great video thank you!

I've tried chemicals, even bicarbonate of soda and vinegar but this worked on the first try!

Thank you so much! You have just saved me so much money. I cannot wait to try this

Good instruction but what about bobbin instruction

Thanks for sharing the knowledge, but come on! A hammer and phillips head screwdriver?? xD

Thank you! I have many cartridges without handles too! I’m definitely going to try this.

Excellent instructions, pulled the sticker from the bottom, pushed open the hole. Filled it with ink & plugged it up. PRINTS LIKE NEW! YEAH 😂

It worked! Thanks so much❤

Omg thank you so much this was very helpful!! Now I can't wait to try out my new machine. Do you do videos of how to change the stitch? I would like to try and figure out how to use the up and down stitch that looks like mountains.

where did the .3 in the 35.3 come from?

If you wanted to drive faster add three drops of just any kind of regular rubbing alcohol doesn't matter what color it is or whatever but only three drops to like one fluid ounce because if you add more than that it will draw all of it out quick

Looks good. I think I'll pull the label from the bottom which will expose the hole to pop/drill out. This way I won't confuse it with the bleed hole. Thanks for sharing. 👍🏽

Hey Chris put a spacer block behind that log piece and push it up against the wall then put two anchors into the wall and strap your clamp to it you'll find it more pleasurable to work also get a taller chop block ergonomics is probably one of the most important things in woodworking so we all overlook! You could also drill a hole down the center of the log and tie it right to the ground with the long Bolt! The point here is getting more secure systems instead of fighting it!

Chris I really think you forgot to add the video here it's only 4 seconds? What happened I was looking forward to it!

Thanks a million. I really appreciate knowing how to do this. It's a major money saver

Good job man, it worked good. Thanks for sharing the knowledge

Cool man, very informative.

Thanks I used this for school lol😊

Thank you for making this! Learning to sew and this made me realize a bunch of mistakes from my first project and helped me thread my machine properly!

well done

We moved from Larchmont in 1972. The house I grew up in was just a block away from the beach and the park for many years I miss home very much and will always have good memories of it.

I was hoping you’d show the actual wiring but good explanation, thank you

My color is is coming out blurry and not colored right ? What do I do ???

Thanks it really worked

mine is not recognizing my ink cartridge after refilling

Thank you for this video this will save me lots

Thank you, great idea!

Hey Chris! Just watched this. Was looking for a simple net knot and like this. Question though is how you finished the side knots. I'm on my second attempt of a cargo net for my pickup..

What if you are using a plastic box? How would you ground the box?

You made sure we knew the direction of the bobbin thread, but not the top thread. It looks like the top thread comes from the right side of the spool and comes in front of the spool and not coming from behind straight out from the left. Is this correct?