Video

Hi sir give me your address please

I love my little Cub. What I decided to do for a battery change is not take off the seat or plastic. I used a wrench extension to remove the hold-down top bracket from the battery. I had to prop up the plastic with a piece of board to get to it. After putting in the new battery I decided to leave the top bracket off cause it's such a pain to get off. Instead I secured the new battery with heavy duty zip ties. Next battery change will be so much easier.

Thorough job

You did that smoothly while holding the camera!

I needed to get to the solenoid on mine. The layout is a little different. Your "plastic removal " part was awsome. I had never done that. Thank You. Your video was very thorough.

My model number only has one "A" at the end

Way too much disassembly done here. Remove spark plug boot, turn of fuel, tilt it on the right side, remove blades and hub as one, remove blade guard on hub, push drive arm on transmission all the way up and remove cable. Then you can release tension to remove install belt. You separate pulley on transmission to get belt off transmission pulley. 10 minutes max and that’s with a stuck blade Hub. Smack it dead center and use blades to wiggle off. People make things harder than they should be.

My lawn mower you just set the dip stick on top of tube

Your video was longer than the time it took me to replace my switch 😉. THANK YOU! If I hadn't seen this video I would have been lost. This is very detailed and well worth the view!

Also quick video don't talk u thorough it

What kind of tape did you use to seal the hose?

I’m trying that tomorrow!!

really?!?!? yikes!!!!!!!!!

Love the way the hub came off after a couple of taps. I eventually got mine off but resorted to using my harmonic balancer. It was on so hard it bent the balancer😂

Can you list where you got the side mirror and part number?

Good idea!

Dude, you tilted that lawnmower with the carb side down. Thought that was a no - no.

Turned out great!

I watched the whole thing to learn there is a “fine adjustment” that is on the outside cable. - thats alli needed to do and I have a really old mower. You should definitely try that first! It’s counterintuitive fyi- you make the screw longer to tighten. But nice video - thanks!

Thank you for the video. Others were saying to remove bolts that my rear pulley didn't have.

I see why the bodies rust through now. They hold a lot of debris.

That's cool, thanks!

So i did this today. Car started fine. But then as i was going to the store, i noticed heat coming from out of the vents, and the gap between the cd player/ ac housing area, and the driver interior plastic covers. Only thing is, i'm not running the heater. I came home, popped the hood, and the engine wasn't even hot. Last time i did this, i didn't take that bottom panel off (the one covering the under part, not the one covering under the steering wheel), and i had no problems afterward.

I operate my own shop. You do not have to do all that. Way too many steps ..

Damn my hub will not budge. Any tips? Beat on it with a 4lb.hammer and no luck

I did mine without taking anything off

Nice video.My cc30h will start but only runs for five minutes then it sputters a lot and finally shuts off. Ive checked the cutoff switches which seem to be working ok. My guess is a plugged gas filter or a dirty carburator. Its gotten worse over the last few lawn cuts Repair shol says I got a five week wait. Ill try a new gas filter,drain old has,and drains the carb bowl.I hope this works. The cc30 is five years old. Anybody out there venture a guess whats causing my mower to shut off?

Mechanics have already changed the ignition housing and the starter in my 2012 Ford Escape, and it's still doing the intermittent starting. Now I'm wondering if the ignition switch is not part of the ignition housing? If this is the simple fix, then I've wasted a lot of money.

Wait, I've never taken apart the covers. Just unbolt negative, unbolt positive tilt slightly, lift out. Done. No need to remove covers.

It’s a two piece pully if anyone was wondering

My mower has a spring behind the trans.if removed you can rotate the pulley for easy access to that nut.

Really good teacher, thanks

Thanks for showing how to do it.

I think you can change this belt without pulling all that plastic off. No need to pull wheel either. Theres a trick to it.

I just completed this belt change however my documentation does not specify a torque setting for the bolt which holds the blade hub in place. Where did you find yours? Thanks.

You don’t have to remove any of the plastic body parts to remove and replace the battery.

Mine lasted 5 years using a battery tender after every mowing and all winter

World's best plow shovel on the wall

Good video, thanks!

Hey where did you get that part? The ignition switch

Cool

Where are you located

I got one for free too! Needed a new carb and a tire.

I didnt take the blade off. The flats on the shaft are more visible and accesible through the bagging chute door . Good video

I just got one of these given to me for free and all it needed was some fresh gas and a few squirts of Fluid Film on the linkages. Does sound like the impeller bearing is a little worn, but it's not flopping around or making too much noise. Tires need air, but still hold some.

Great improvement.

Nice video

Hello, MrFixit. I was wondering if you have a video showing how to fix a hunting /surging engine. Same snowblower model as in your video. ST824. Much obliged you. Boz

Yeah That Isn’t Bad u did ok good job