Video

Thank you

Car looking great !!! Where did you buy the spacers ?

What happened to your group? I saw your other video and I thought it was fixed

That A/C is essentially a PTAC unit.

Is there an update on how is it holding up over the years?

Common dodge L

Are you ten? Because your music says you are ten...

You could’ve use the 12 gage wire yellow because your using 20 apms breaker

what wheel spacers did you get do the fronts do they have to be 66.1mm ? cause on my zx cause of the front spindle part are a bit wider on the hub they dont sit flush do you need a 73mm center bore wheel spacer ?

Lifesaver. Spent 20 minutes trying to take off that big nut

Love it!!! I would recommend using a piece of cardboard to remove excess paint before applying to stencil.

thank you man ive been trying to find this for a while now

I just purchased some adapters from car depot but there adapters are flanged unlike the ones you have which do not have any center flange

1:46

Thank you for great review looks great 👏🏽 love the color of your house as well. Do you mind me asking what color did you use for the exterior? Thank you!

How much was the concrete pad? How much psi rating did you go with?

With the ecu being from flagship 1 did you have any problems so far?

Bro this video was amazing this is literally the issues and what I was thinking of doing

I would also apply the sound deadener to the inner door skins and the outer areas that the door cards are attached to!

There just isnt any good method to install these without damaging the bearings😮. I wish these were rollerbearings, that way you would have some way to install them without transferring the forces through the balls. And also it would give you the chance to "service" them like changing grease and tightening as needed.

What size bolts for the engine stand??

the finish looks so nice. well done

Cool race car.

All of these methods are dangerous. Heating causes fumes that are harmful to your lungs. Wire wheeling produces dust, which is also harmful. It's best to go to Home Depot, buy Citristrip, brush it on, cover it with plastic, and wait a minimum of 24 hours (ideally 48 hours). The paint will come off easily, similar to peeling an orange.

also it looks really good

did you apply a bonding agent after etching the concrete before applying the paint??

It's garbage! Ive bought better paint from Wal-Mart!

Look at other reviews. Please don't waste ylur your money.

Nice video. If you don't mind me asking, how much was that concrete slab? Dimensions? Thanks

Good job, but Why you leave no finished concrete on front garage under garage door? it not looks good when you open the door.

Have you had any issues with the wiring running 10 gauge?

Do tou got to paint it every year

Where is that horn kit. I can not find the horn kit anywhere!

Is that the same primer you used on the the frame ?

I’m going to be printing my z just have so much rust. I wanted to ask why didn’t you spray this primer on the roof I believe you used epoxy instead?

Nice video. I liked the car the most ❤

Metal to metal to re install the bearing is the correct way. Don't use the wood. Make sure the metal pipe is squarely to the inner race.

We built ours yesterday, cant find where to put the long thin angled metal strips (roof supports???)

I'm here 2 years later but what i did was place a small fan on a shelf above and skip the unit's extra fan.

great video

I used to work as a steering design engineer and would NOT do this. 1 These EPS units are designed for use inside the car where it's clean and dry, with moderate temperatures. Not under the bonnet, where it may be wet or hot. Water ingress may cause corrosion on the circuit boards. 2 According to Newton, all the assist torque is reacted through that little mounting bracket. 3 The input shaft normally has an upper steering column and a bearing at the top, which eliminates bending loads. Unlike this installation, which practically guarantees them, due to cardan joint angles etc

Hey did you save the spare tire well? I need one for 77-78

Bit of white sprit to wipe off the left over bits

Doing this with a landcruiser. Bought a factory wheel to replace the nardi. But didn't realize the landcruiser is an older stock that has the brass ring while the newer wheel has the harness wired for the horn. So I poached the horn ring off the nardi but realized the ring is touching the metal of the wheel which grounds it right away so ill have to insulate it from the wheel and try again.

How much did the concrete cost?

I am having the same problems with a 2013 ford escape. Thanks for the video!

Hi, where did you buy this one and how much was it ? And great job. Looks great

Is it necessary absolutely to have a base?

Sweet

Bro I never heard of you before today, but that opening was classic and I needed it this morning. Thank you