Video

Dude needs to learn how to use a torch!

en tous cas, sans outils, sans pièces, ingénieux, ils ont le coeur à l'ouvrage, bravo !!!!!

16:32 / 37:51 Modren Techniques????? where?? is normal way of repair

Bad work :/

عمل بدائي سيء

CAT 부품을 파키스탄에서 제작 생산하나요? 호환부품

Great work. Keep it up...❤

Thank goodness he’s wearing safety sandals 👍

I'm surprised that those guys with their blowtorch's and hammers were not the first to the moon ❤

I've done a great deal of equipment repair welding. I have to agree with many of the comments on this repair job especially the prep work (or lack of) and the use of 6013 rods instead of a 7018 type. But, in their defense, we don't know all the details or the demands placed on them, or what they have for equipment or skills. I'm sure they do the best they can with what they have and if we were in their shoes maybe we'd do the same.

Good work ❤

No fitter welders there just a bunch of chancers , then I suppose pay peanuts get monkeys

Good job! All tolerances are guaranteed less than 5 fingers.

I feel like so much of their issues could be fixed if they just did some damn prep work and not rushed in.

I have a lot of hours in 966D and 966E loaders like this one, used in mine duty. NEVER saw any of the cracks and breaks like on this poor machine. I would like to see the operators in action. Also, the welding rod they are using is a Bridge Supreme J421, which is a 6013 classification. Should be a 80 or 70 low hydrogen rod used on those loader arms.

back street job not inpressed at all

I worked in a rock quarry for years as a welder repairing the heavy equipment and rock crushers. What these people did here to "repair" this 966 boom is utterly embarrassing!

Defiently ain’t no cutting edge engineering 🤮

Good work

Good work ❤

Wooo amazing 😮😮

goodjob

Great job 👍

0:50 - 1:10 и снова всё отвалится по тем же местам. Чем тратить деньги и время (что в условиях интенсивной эксплуатации тоже деньги) на бесконечные ремонты, не дешевле было бы купить новый или б/у, но не выработавший свой ресурс узел? Или труд там настолько дёшев, что...

Amazing

good wheel loader pin bushing repair, friend 👍👍

👌💯excellent

💯👌👌😎

This Loader Boom has been repaired over and over again in the same place and they keep making the same mistakes.

Good work, done outside the workshop,my compliments !

Great work😮wow beatiful

So amazing work I like it ❤

Add a doubler plate as reinforcement..😂😂❤❤

Good 👍

good work

The welds are full of slag and it will break again next week.

Oh mein Gott 🫣😂😅. Zwei Wochen später, wieder das gleiche machen🤦‍♂️. Schaut euch lieber CEE an, der hat wenigstens Ahnung und kann richtig reparieren. Das hier ist nur Pfusch

Great job 👍

Great work.

Great work.

they always amaze me

A Patchy Indians..😂

Such creative videos you’ve on this channel. Just subscribed!

So good

Never seen a loader with so many cracks.

Good job

Torc converter bolt failure cracked housing caused fault in bearing witch hurt pump , I'm I close ? Got the same thing on D 5 dozer ,, good job people 👍🙏

ماشاء الله 👍👍👍👍

The Paint is the Superstructure on this Loader

👍👍👍👍