Video

Спасибо за отзыв!

Вот когда поставлю электро привод,тогда и пигодится это ;)

@@georgedarchinian Теперь все встало на свои места, удачи вам!

Спасибо! 5200 с акками 4000 наверное с 5 амперниками так и будет 5500 Верт отличный! Небо и земля по сравнению с логой

@@georgedarchinian Как оказалось свет клином не сошёлся на лого!)))

Мой XL700 с 4400х2 5270. С 5000х2 5390. Так что чуда не произошло. Хотел до 5250 с 5000. Хотя и регуль лёгкий.

Hello.This project was many years ago and i don't remember details but i had stepdown dc/dc from 2s to 1s to power main board

Thank you 😊 . Do i have to put another receiver and controler or the stock ones works with brushless tail? Cause I don’t get tail signal when installing the brushless tail

@@thedogmah2 stock receiver works. You have to find signal for tail. I dont remember the pins on the board

Ok thank you hope I succeed

Ha ha! I was pirouetting in the same room on 450 trex years ago ;)

Спасибо!Стараемся ;)

Спасибо Петя!

Thanks!

Thanks for comment and sharing your experience. I added oil but it didn't helped a lot. Looks like the shaft or bushing worn out. Servo did about 400 flights.

Пожалуйста! Снимал именно для того,чтобы помочь другим.

Hi Thanks for coments. I don't have it anymore. Got me Logo 690 long time ago/ Yes,i had balance problem but main problem was tail belt transmittion.Too weak for my flying style

EniSy kin да

Gyorgy Toth This is older model.

Gyorgy Toth That was scorp sk3 500kv,kontronik 80A,servo KST 815 805 and vbar neo.

Да. И руки дрожат у оператора ;)

пожалуйста!

I have brushless tail motor :)

George Darchinian could you please be so kind to forward me the site do I could buy that for my v977 please?

hobbyking.But tail motor esc i think they have out of stock.I bout it few years ago.

George Darchinian is it that big of a difference will I be missing out? Any other recommended upgrades? Thank you very much for your expeditious response.

I've upgraded tail to brushless because i fly too much and tired replasing brushed motors.I recommend replace stock prop on something bigger diameter like they have on banggood in v977 section so the load on brushed motor will be less and tail will hold better.Also bigger prop will save brushes in motor because motor spins less rpm in that case.

Graphene is much better!

Do you had perhaps Turnigy nano-tech 600mAh (17g) 35/70C? Graphene version is not yet available in my country. Are you using 600mAh graphene cell?

Yes i have nano tech.there is video on my channel as well.I'm using 600mah graphene from hobbyking and i prefer graphene then nanotech.

Ok, thanks for info. By the way, i see different connector on graphene battery, did you replace connectors on battery, helicopter or is there graphene battery with proper plug?

yes,i replaced connector on heli.

Привет.Во первых все симптомы того что серва в реверсе. Надо начать с вкладки движения каналов,там где настраиваются каналы передатчика.Правильно ли отображаются движения хвоста стиком?Движение стика влево,канал должен показывать лево.Если там неправильно нао реверснуть в аппаратуре,если правильно в аппе ничего не трогаем идем дальше. Правильно ли указано расположение коробочки?Проводами к хвосту,к носу и т.д. Если неправильно исправляем там. Далее вкладка хвоста. При движении стика хвоста влево слайдер должен уходить вправо к балке. Если не так то делаем реверс на этой вкладке,НЕ в аппе. Ну и последнее,правильно ли указан тип сервы на этой вкладке?

Hi I'm still on 1S. Unfortunately all my parts that i used for brushless tail are out of stock. But anyways,you need motor,esc and programmer because esc comes with different settings and you need to reflash it with Blheli to work in V977. For brushless tail you need motor from Hobbyking. www.hobbyking.com/hobbyking/store/__25436__12000KV_Brushless_Tail_Motor_for_Micro_Heli_suits_MCPX_FBL100_.html Esc either one from Hoibbyking. www.hobbyking.com/hobbyking/store/__44315__SuperMicro_Systems_Brushless_ESC_3_0A.html Or www.hobbyking.com/hobbyking/store/__44697__SuperMicro_Systems_Brushless_ESC_3A_Mi_3A.html And programmer. www.hobbyking.com/hobbyking/store/__25433__USB_Programmer_for_Micro_Helicopter_ESC.html Also you need some soldering work on ESC to solder connector for programmer. Also,i recommend to replace original main esc with this one. www.hobbyking.com/hobbyking/store/__25432__Brushless_10A_ESC_for_Micro_Helicopter.html It already has connector for programming,lighter than original about 2-2.5gr. and you can flash it with Blheli to use governor. Good luck

George Darchinian Thanks for the quick reply. Just to get it clear again. I'll need the brushless motor, the programmer and either of the 2 ESC's and optional to replace with the 10A Esc right? Also is there any tutorials on how to program the ESC because I haven't got a clue:? Thanks so much!

Also any info on soldering diagram? Like what wires go where...Thanks for your help man!

jakeboynz there are some topics on helifreak.Sorry but i lost links on that. Here is one of them. www.helifreak.com/showthread.php?t=390517 Just ask over there.

George Darchinian Cool! Cheers bro.

you need to use the hover debug, goodluck some people have had issues calibrating the 6g mode. In this video the heli is not being flown in 6g mode.

ops ailsom não consegui cara e vc conseguiu fazer o up pra 2 s??