Video

Its the rollers that fail and that failure wears the cam lobe. Later lifters (I believe 2017+ srt trackhawk) have bigger needle rollers in lifter roller. How many and how common do these later lifters fail??

This is outstanding, been avoiding doing the rack on ours slightly leaking for like 4 years now just starting to get an ugly leak lol thank you so much!

Did exactly what you said bro my dtr turn signals don’t work

Did exactly what you said bro my dtl turn signals don’t work

Drl also don’t work

When the lights are on my blinkers won’t work. Any help appreciated

Hey I have a question would and 2015 and up 6.4 be plug and play for a 2011-2014 Rt ? If so could You tell me what’s needed

Try that on an 07 edge. You will fail.

PLS HELP So I have a problem, the camshaft that should be at 12 I can't even get it to turn. I place it on the lil notch and it doesn't turn at all I haven't tried to force it but it won't turn any reason why or what I should check for or do?

Great video!! Will be doin this when I get home on my 5.7 challenger. Almost thought that was my dog in the background😂😂

Thank u so much your video helped me to connect my newer head lights

Do u have to change the hood and fenders when doing the swap ? And if I have a 2015 donor car do I just take the whole front end , lights , hood and fenders ?

You did a good job though.

I saw that with the tensioner bolt, that first bolt never clicked and it kept turning and you stopped, you know it's on the verge of breaking,😂 you went from 22 ft lbs, to 16 ft lbs then to 12

Only Gripe With eBay Ones Is You Only Vouch Them For A Year. Being A 900HP Car I'm Thinking It Doesn't See Typical Hemi Daily Driving. The Average Life Of MOPAR Lifters In Hemis I've Seen Is Around 150K. Got A Set Of Hellcat Lifters In And So Far Had No Issues With 80K Miles. Truck Has 230,000 Miles Now. We Will See If They Last To 300K.

You can also verify timing after the pump is on by looking at the bottom key-slot. It is still visible and should be around 2 O'Clock.

Very easy to follow tutorial, but do I stop the hyper flash?

have you finish your ideler brackets yet

1st time seeing a challenger cluster gage on the charger and I love it

Doesn't work like this ob ford edge must drop exhaust flex pipe drop 4 rear main large bolts the torsion bar will simple not swing out as much as that ford flex does. Hits the wheel well and not enough room to rotate rack out.

I knew it could be done this way after watching an hour of another video that dropped the sub-frame. Thanks for confirming.

Would this be the same for a 2019 300?

How many rw horses you pushing

Why let it run and pull the fuel pump relay ???

Do you have brackets for sale ? I’m going the hellcat blower install on my car

so couldn’t i technically run the hellcat blower on a 6.4 with basic installments on without the pulley hooked up being more used a intake manifold with stock 392 power with everything else stock?

Yo was your lights DRL flickering when u converted it?

Very helpful, I did a 2021 scatpack swap in my 2012 Chrysler 300. I used a 2015 Dodge Charger front wire harness, I see that the Charger harness does have 3 plugs. I am reusing my 2012 300 headlamps which only has 1 plug. Have you done this conversion before? Where can I get the diagram for the 2012 300 headlamps?

I have a 06 Ford 500, if I have my rack and pinion replaced, how much more to just replace the sway bar's, and tie rod end's? I've already had control arm's replaced. Tbank you! John

Thanks! Confirmed what I thought it would take. And thanks for the tip on the AC line.

How to possibly get hellcat swap parts from you?

I’ve looked all over, but can’t find your website or email address interested in the brackets in adapters

Thank you, I was just quoted $956 to fix my rack and pinion

I have a 2012 rt looking to change the shifter and the ac controls to 15+

How do I change to the newer ac climate control

Hey how did the car blow up I want to put supercharger on mine just don’t want that to happen

Damn my cousin had to pay $2700 parts and labor smh I didn’t feel comfortable doing this but next time I will

Now we need a video on how to do the new 1st gen 06-12 dodge charger the same way you did this.

How many resistors do I need 2 or 4

Really hope no one is putting the timing chain tensioner at 21ft pounds because it won’t even go past 10 before breaking a screw

Where you get the capacitor I’m almost done with my swap

I want to buy the Kit whats your insta or a way to reach you

What about the back ?

wont work on 2008??

How much u charge for this job?

What i want to know is what you did to extend the pulley on the snout cause the supercharger i have has the hellrazor pulley on it. Would love to use the decoupler pulley but doesn't look possible

Exactly what i want. My man i can't wait till we Collab and build something together. I should have you out at my shop and we film it

I love the look of the 2015 front end. Definitely looking into doing that as well. After I get the engine stuff sorted

Yeah I needed a new vacuum line to the brake booster, as I couldn't get it off. Inner diameter is 11/32 by the way.

Hi I will like to buy the kit for a 2012 challenger rt hellcat conversion