- 1 301
- 9 555 734
small engine guys
United States
Registrace 13. 10. 2019
Easy step by step small engine repairs
Video
2017 gmc terrain passenger headlight bulb replacement
zhlédnutí 78Před 16 hodinami
h11 bulb amzn.to/452GpFz
The customer states i had a lift kit installed somewhere else i need an alignment
zhlédnutí 278Před 14 dny
The customer states i had a lift kit installed somewhere else i need an alignment
im no rocket surgeon but i think these ball joints are bad
zhlédnutí 195Před 14 dny
im no rocket surgeon but i think these ball joints are bad
customer states my rear brakes are fine
zhlédnutí 240Před 14 dny
customer states my rear brakes are fine
customer states front ends been making noise
zhlédnutí 1,1KPřed 21 dnem
customer states front ends been making noise
why you dont get an aftermarket o2 sensor!
zhlédnutí 556Před 28 dny
why you dont get an aftermarket o2 sensor!
2020 toyota 4 runner oil sevice notification reset
zhlédnutí 110Před měsícem
2020 toyota 4 runner oil sevice notification reset
customer states car fell off the lift at another shop
zhlédnutí 955Před měsícem
customer states car fell off the lift at another shop
my daughter learning how to drive the Yamaha blaster 4 wheeler
zhlédnutí 160Před měsícem
my daughter learning how to drive the Yamaha blaster 4 wheeler
420 night market music fest jacksonville
zhlédnutí 110Před měsícem
420 night market music fest jacksonville
drum circle night market at the portal Jacksonville Florida
zhlédnutí 89Před měsícem
drum circle night market at the portal Jacksonville Florida
warm up for john guinta arvid and sandie sounds of stream jacksonville fl.
zhlédnutí 56Před měsícem
warm up for john guinta arvid and sandie sounds of stream jacksonville fl.
dominos nissan leaf electric car emergency road kit has jumper cables!
zhlédnutí 66Před měsícem
dominos nissan leaf electric car emergency road kit has jumper cables!
replacing the radiator fan on a 2023 Chevrolet Malibu
zhlédnutí 189Před měsícem
replacing the radiator fan on a 2023 Chevrolet Malibu
customer states i dont need a battery
zhlédnutí 1,8KPřed měsícem
customer states i dont need a battery
reading a nissan hardbody computer with the kingbolen ya200 obd2 reader
zhlédnutí 74Před měsícem
reading a nissan hardbody computer with the kingbolen ya200 obd2 reader
2016 dodge ram 1500 check engine light reset kingbolen ya200
zhlédnutí 92Před měsícem
2016 dodge ram 1500 check engine light reset kingbolen ya200
measuring the front wheel on the battery charger.
zhlédnutí 105Před měsícem
measuring the front wheel on the battery charger.
reset the check engine light on a 2012 nissan frontier kingbolen ya200
zhlédnutí 82Před 2 měsíci
reset the check engine light on a 2012 nissan frontier kingbolen ya200
Great Video! The only problem was the CONSTANT wind noise.
Its 98 degrees here iñ the summer. 80 in the winter. Fan stays.
I used a 17mm socket wrench.
Cool video. Thank you. I purchased mine in 2016, and it has always been a cold blooded SOB from day 1. After about 2 minutes, it’ll go full RPM. I’ll be seeing about getting those caps out, and see about adjusting it. Thanks!
Thank you for taking the time to make this video and post it. The information was very helpful and I got the power washer up and running. The gas had dried up and left deposits in the jets. My local repair shop wanted at least a hundred dollars and is backed up three weeks to repair so this was very helpful to me!
Glad i could help. $100 bucks is a fair price. Sounds like at least you have an honest shop near you.
@@smallengineguys I thought $100 was okay just needed to get the washer fixed as the weather was perfect and couldn't wait three weeks. Your instructions made it very easy.
Love the video, dying over your shirt !
Lol thanks
thanks bro
Thanks for the help, works like a charm now.
Awesome, video on my friend help me out so much. Couldn't figure it out, i just cleaned my carb out thought everything would be running well but it was struggling and bogging out. Did exactly what you said? It's running strong as an ox..
Any chance I can get you to send me the numbers for that carburetor? The link isn’t working. Thank you.
I followed this video exactly and got my unused, sitting in corner of garage Generac Power Washer up and running using this video. Thank you for posting this one
How do you remove the pull cord cover on this model? It looks like it is kept on place by 4 ribets. Our was it Allen holes that were stripped?
Does the acid cleaner harm the O - Rings or plastic? Thank you
No
@@smallengineguys thank you
What if I put too much gasoline in it?
No such thing
That's nice
Best video I found on this issue.. Thanks 👍
I hit a vine on a tree and my string came out. Now when I put new string through holes and turn the bumper, the string won't wind in, but bumper turns easily. I have the exact same Homelite weed eater. I wonder why string won't wind in and the bumper turns?
I have a husqvarna professional I need recoil repair will the part still be able to fit on my husqvarna model
This does not help. We learned what NOT to do.
So you learned. Your welcome.
Just subbed love the channel
Gear box is good. Cable is good. Cable doesn’t spin with head off. What could it be
Clutch could be frozen but more than likely one end of the cable is rounded at the tip.
@@smallengineguys took it apart. It is the clutch drum. I have to replace the whole cover I guess you can’t just replace the clutch drum and the bearing is what I’m seeing online? It wasn’t spinning. I broke it free and tried again spun for a second then stopped again. I’ve used the unit for maybe 6 hours total. Must of overworked it.
@@user-bb5ky4uz9p yep sorry whole cover time. And yes way overworked lol.
Here before it blows up
Is it ok to use a different type of grease than what came already in my boat trailer bearings? Can you mix different greases and be ok, or do I need to find the same one they used?
any grease is better than no grease. you can mix it its fine i use red axle grease most of the time
Want model 51952
Pretty sure its the same thing just yours is curved shaft.
Thanks so much! This was super helpful!
Glad it was helpful!
It's a POS homelite just saying
I dont make them. Just fix them.
@@smallengineguys I know you did a great job on that one just felt bad for you after all that work it still won't start
@@danielpadgett2831 it happens
next time get a better set of tools man. lol
ill do this shit with 2 sticks and a rock
I have the same engine on a tiller and I just bought a new carb for it and I can get it to idle but I can't get it to adjust. It goes up and down up and down in rpms and I can adjust that out but when I open throttle it it wants to bog down . I'm about to throw it, I hate carbs on 2 strokes. Correct mixture 40:1 new plug, Ive done ever combo on the pac man screws and fine tune and it still wont run right. Any thoughts? I have the idle perfect but as soon as I touch the other side it sounds like a rev limiter up and down ,up and down I adjust it back perfect idle but when I open throttle it's dies or does the rev limiter shit. Super aggravating
there are 2 adjustment screws next to each other on the carb. the one closest to the air filter counterclockwise a quarter turn. here are the tools amzn.to/3yR9ms8
Since the fuel line is on one side of the carb and the primer is on the other, does the primer bulb suction side connect to the carburetor to pull fuel through, or does the discharge side of the primer bulb connect to the carburetor?
Primer sucks fue from carb pushes fuel in the tank
Thanks dude , I almost threw this shi* across the room
Looks like the last time it was listed on MLS the asking price was $49K 6/10/22, and then the listing was removed: Date Event Price Price/Sqft Source 06/10/2022 Listing Removed $49,900 $48 realMLS
No idea. I just did a video for the guy that was selling it.
I followed your directions and it worked exactly. Thankyou. I almost trashed my blower. Working like a champ. Thanks again!
Glad it helped
I have the exact same trimmer and this fixed it perfectly.. ty
Thx you have saved my life today thx thx thx
So instead of pushing fuel through with the primer, you're suckling it through? Not sure I trust my primer bulb to do that reliably. But good video explaining everything you're doing. .
it sucks fuel threw the carb. you have to have a direct line from tank straight to carb. if you put the primer in-between you'll get air bubbles and the saw will stall a lot
@@smallengineguys Well how about that. All these years I been jamming by thumb in the fuel bulb thinking I was vaporizing the fuel in the carb, only to find out I was just firing it into the return 🤣. My saw was in storage for 5 years and when I grabbed it my fuel line literally disintegrated into pieces no bigger than 1/8 inch, so I really have no idea how it was run from factory.
Your in the way of alot of the video just saying
Watch a different video.
Thanks bud
No problem 👍
What happens if the back seal comes off? In the carb
Great video. Easy to follow.
Glad it was helpful!
When I tried to take the float it is stuck. I can’t get it out. The jet stays in the body. Any ideas?
soak it in diesel and try again. other than that its new carb time.
@@smallengineguys I soaked it in carb cleaner for a few minutes and was able to wiggle it out. The needle and jet were corroded. I pulled and cleaned them. Fired right up! First pull
Is there a gasket between the carb and the engine? I didn’t see one in the video.
yes it stays on the engine
Hey, the discontinued the fuel line from amazon. Can you let me know the dimensions that worked on this model? Thanks!!
amzn.to/3wQYmuh
@@smallengineguys Thank you! Any idea on why its bogs out instantly after only changed the fuel line from the fuel tank to the nipple? It worked prior, but I had to change it because their was a leak. Thanks!
@@williamreichert289 takes a tiny spec to clog it.
@@smallengineguys Thank you sir!
@@williamreichert289 sucks but probably new carb time
Thanks!!!
Perfect thanks appreciate it
No problem 👍
It helped!!
My Toro Recycle 19 mower would start but die in a few seconds. Armed with a carburetor cleaner I followed your guide to open the mower for the first time in my life and clean the carburetor. 2 hours later, it WORKED!! It’s not a professionally-edited video but it saved me loads of money, time and frustration. Thank you!!!
Appreciate you sir. Thanks 4 sharing
My pleasure
Thanks man, saved me from having to pay someone, or a faulty install! Thank you for making such a specific and detailed video, it was exactly what I needed!!!
Glad it helped
On that same type blower I need to see how to remove the cover off the engine
Thanks found ecxcitly what I need to know ,pac man driver.
Glad I could help
After rebuilding the carburetor, I am getting foam oil coming from the air intake (small line). What could be the cause of this?
carb is bad. needle valve is leaking