Video

A treasure to behold. A short, no likes video from 15 years ago

Which software is this?

Thank you for uploading this animation. What do you mean please by mass ratio?

resulta may be tied to your systems natural frequency

Do you know Rocky?

hello sir i hope you are well can is ask for help about vortex ring it is my new academic project and all i found a little paper and did not help me i want to simulate it using ansys every time i do that the result is stream lines and no vortices is founded or formed (no circulation) what that thing i missed ????? thanks for your time

Im trying to do a design like this on solidworks. Can i use your design as a base to work with?

Hello,can I ask you something about this, I am so confused about the VIV simulation with the STAR-CCM

A lua é translúcida

If i see this i understand more about how many fish are using the same technics for swiming. Their energy is far less then we use to put a boat in a moving direction. Wat is you use this principe to power a boat.

Initialize everything with 0 (except temperature = air inlet temperature). Run simulation with time step of 0.001 seconds for few time steps (2 is sufficient). Create a small cell register overlapping the region where the fuel is within flammable limits (ch4 molefraction within 0.045 to 0.147). Patch progress variable = 1 in this cell register. Continue simulation for 10 more time steps. Then you may increase the time step to 0.05 seconds.

does the Reynolds no. not vary throughput the domain. Where is 100Re ?

Could I use your animation in an article I am writing on Karman Vortices with appropriate credits ??

Please, share for this tutorial faizamine20@gmail.com please

looks like a Whirlpool But it's flat on the sides how much more Particles and perhaps Frames of video would be needed to make it not stuct to walls and more like an actual Whirlpool ???

Where's spongebob

Great vid. Guys. Thankgod for Gopro! :)

In my case I don't necessarily want to surpress ALL vortex shedding; just that of one chirality.

Tendrá medidas reales?

What is its practical application???

Hi, thank you very much for you video.may i ask you a question? Why I follow the I followed the tutorial within ANSYS on combustion, but the fuel seems to not be fired? there is also no CO2 generated.

Please, share for this tutorial nanang@pnm.ac.id

Ollie, how are you doing? Always welcome to come down if you get the chance. Pete

This is very nice. In real world, you see truck platooning on highways. It will be interesting to see 2 or 3 blocks/ bluffs simulation, just like see 2 or 3 truck on highways!

Could you please give a tutorial of your simulation? Thank you very much.

The T-Rex has two blades. and it shows the downwash column is very steep. I would be interested in additional CFD results, in case the helicopter would have3, 4 or 5 blades instead of two (same lift forces of the rotor circle). The interesting question would be, how the downwash column would look like in these cases. I guess the outer vortex would bend a little outside and the VRS would impend at lower speeds and descent ratios. I really would appreciate an additional CFD simulation for comparison.

Hi. i want to ask how did you take the animation of this simulation? my thesis also this kind of thing. a help from you would be really nice. thanks :)

please , can you send me this mesh file .thanks

would you kindly tell me the computer specifications you used to get it done (i.e. processor speed, ram, graphics card).

can you send me the combustor file?

Hi, this is fluent or CFX?

hi, i'm interested with your work. would you please share with me the tutorial?

Hi nice video, but where are the turorial?

nice look my rc car fireworks launcher

@olliewest

@luigiblaze2 and pass an electric current through to get red hot,

@luigiblaze2 They use a very thin metallic wire attached to the fuses.

sweet. how did you light it ?

hey guys check out our channel we've got another flight video from Duncan and also an interview!:D

it is to improve aerodynamics

dude, don't sue me but i think i will use your design in a replica i was thinking of doing....

boring same moves all the time

Where do you get everything in the demo?

This is an amazing vid- much better to watch than some of the "stickbanger" stuff that most people seem to think is cool,,, and what makes this video even more amazing is that he used the original Align 3g unit!

@womackke Try going to ''Import'' under the file settings, I think I used import KES or raw image or something like that. I didn't work 100% as the file I downloaded showed it with grass on the ground and other sections which were not imported. Hope this helps, if not message me back.

how do i import this into realflight 4.5 I am having trouble

@Bertziethegreat This is not a 100% accurate representation of this section of an ariel atom. I did what I could from images and blue prints found on the internet. I did however re design it to reduce weight (see link in description).

So what's the deal with the rods connecting to the coilovers? Why not have the coilovers connected directly to the A-arms?

It looks great, but what Atrainskate said, makes sense...

Looking good mate