Video

Amazing explanation, you make it simple and easy to understand, thank you, watching your videos all the way from lebanon

THANK YOU SO MUCH FOR THIS VIDEO! EXACTLY WHAT I NEEDED TO HELP ME DO MINE!

Thank you for providing much needed information. I was not sure how to relieve tension in the torsion bars on my 2002 Chevy Blazer safely. This seems to be the right way to do it. I've seen it done by lowering a jack but I was concerned I wouldn't be able to get the same tension back on top of the obvious safety problems. This makes the first idea seem so dumb; it's literally just a bolt.

Thanks for the clear instructions

I replaced my caliper and hose when I first start using the brakes they are nice and easy to push when the brake starts to drag it’s only one wheel and the petal gets hard to push

well this video is absolutely worthless

Any one know why my hydro boost not getting pressure it’s ram dodge 2010 3500

Nice work , Bro i have some question regarding Hybrid ECU , tech. change new HYbrid ECU and after that the vehicle not working/start. There is a code : P0A0A92 ,. What the posible cause ?

thanks for the video! out of curiosity, what temp would a rotor be under normal conditions?

So this makes it like a normal car to brake?

To Much Talk

What happened if the emergency brake is frozen or just does not hold? Due to most people dont use it?

Very good explanation

What about taking the tubes off, excess fluid, etc? Finish the job before you end the video!

Excellent ! Likely is a worn or missing “O” ring .

Well this was helpful but a terrible to follow video. You skip so many steps and don't talk about what tools, sockets, or bits are needed.

Can I delete it entirely and run a hydraulic hand brake?

How refreshing. A straight to the point guide with excellent information. You saved me a ton of stress.

I believe there are some NA SBC racing engines with 23 degree heads that have achieved over 100% VE. Am I right?

How do I reset the heartbreak on a 2015 edge

Interesting

First

This is illustrative to see out of the car but you can do this with it installed on the vehicle and use the pedal.

I have a 2019 chevrolet equinox ls, we changed the shift solenoid and it drove perfectly but now we are trying to do the transmission fast learn adapt but Drive is not showing. Any help please?

How can you tell if the seal is PTFE?

Hello, can you please guide me, how should I change the battery of the Nissan E-Power Sylphy hybrid? I am a master Toyota technician.

Hi bill I have a 2017 e class Mercedes and fitted new brake actuator’s and the car won’t clear the red parking warning on the dash with a diagnostic tool can u advise all parts from Mercedes as well

Thanks bro,helped alot.

Watching this 3 hours before my mechanics exam.

Good video 📹

Thank you for this video !! Dealing with this issue right now on my 2022 RAM 2500 diesel .

looks like dish soap . correct ??

But what if I don't have that what else could I use?

I was told not to run the engine and pump under vacuum

You are explaining nothing,BLA BLA, with no point.If So,ordinary people can do it or not? You have to answer one-two sentences ,not complicated unnecessary prestige.

I've seen this in Texas with less than 80k miles on these Rams. I think it's a poor design due to not enough length of the stub shaft into the CV for support. It also gets accelerated wear with a leveling or lift kit causing more angle on the CV joints.

what is name of tool?

Why doesn't anyone show how to bleed a four port master cylinder.

What about coated rotors?

Hi this is my first time encountering your channel. Nice video, would have appreciated more detail on the hookups

how to identify the trigger wire??

Outstanding vid! Super helpful.

Anyone can say why my car breaks is low even though my disc pads are new?

2.4 subura forester where is all the sensors 6:23 6:26

2.4

On a subura forester where is the air and gas sensor

Really helpful