Video

I know where that Homie Depot is coming from 😃

Rubio Monocoat is great for color matching and evening tones. We build a ton of vanities and our top request from interior designers is to match the flooring or other trim work. We’ve found that water popping the grain helps as well. Great video, thanks for sharing. Headed to the shop now to experiment with some green stain!

Can it fix the spinning screw that attaches the chopper jar with the main machine. It has broken due to overload.

Is there two 02 sensors is there one before and after the catalytic converter ? Cause there is 2 different ones to buy online, if so which one is this ? Thanks

Going to attempt! How many square feet did you do how much did you buy and how much total did it cost you?? This looks amazing! Also, how long in-between steps do you have to wait. I have dogs and no where to put them

Right on! 👍🏼

Long term report? how did the fix hold up?

Great job man

Looks Great!!!

What grit did you use to sand/clean the floor?

I wish my ceilings weren’t popcorn 🍿. I have to do a drywall repair that’s been done in the same place twice now because of plumbing . I’m dreading it

So I should use and umbrella ☂️ while applying

Tires toooo wide. Looks not fitting the 4R classiness

Hope you got to ride in Moab too.

Great video editing. You also have a good “real world” style.

I’ve got trust issues too. I do my own oil too.

you are a smart stupid

There are even tripod wheels that you can add to the bottom!

many of the videos show rinsing the stain with water. How do you get rid of the water? Water vac it up? I don't have drains in the room. Not like patio which is outside and you can sweep/wash the excess off into the ground.

Thank you for this! Loved the honesty and how clear this whole process was to follow. I’m trying to redo my concrete floors after flooding and it’s been hard finding straightforward info like this so I appreciate it!!

Will it fit 16 inch and 20 inch kids bikes?

Thanks so much for the vid man!

For a guy who announced it wasn't time to be funny, this video was hilarious. (Beautiful home, though).

Totally subscribed bc you made me laugh… thanks for the tips on painting handles… I’m going to just buy some new ones & get rid of the knobs 😂

What’s the stain on your wood floor? Did you buy them finished?

Who the hells the guy with no beard or hat on? 😂

Thanks for the video. Just done this job on my son's Mk7 Golf GTD, after getting P227100 O2 sensor signal stuck rich bank 1 sensor 2, using a £60 Bosch sensor. Access to sensor 2 was really tight. Couldn't get a ratchet on the sensor socket, but managed with a tommy bar (trolley jack handle slid onto it for extra leverage). On this model the sensor plugs in under the car and further back. Had to detach and bend out a section of heat shield and some plastic trim. Liqui Moly - Pro-Line Injector & Glow Plug Grease was used on the threads of the new sensor.

You have a good sense of humor and I like your videos but it's important to talk about inflation and the other problems of the many caused by such a few. The mainstream media pushes false info, we only have each other on platforms like this that tell the truth.

Still holding?

Dap caulking is garbage . I’d only use dap for hud housing

That’s about right. $1000-$1500 /day for an experienced painter. Anyone can spay paint. You’re paying for the prep. I’d charge about the same price and it would take me and an experienced helper 6 days

How many kits did you have to buy for your basement?

You are to shake it upside down. Spray continually back and forth very quickly. The key is the further away from the ceiling, the better. People put it too close to the ceiling. They don't shake it upside down. I'm told sitting it in hot water before using it softens and loosens it. Then shake UPSIDE DOWN for one minute.

There’s also a big difference between a $20 spraygun and a $13 tip off Amazon and a pro level $400 spraygun with a $50 tip so if you’re thinking about DIY you need to factor in those costs as well

Watched this video 2 months ago, and went back to it last week. Dude, you just saved me 4 to 5,000 bucks. Thanks, buddy!

Came for the info, stayed for the comedy. 😂 Thanks, Bruh!

More 4runner vids!

Won’t the chemical leech into your food??

Good vid, i just picked up the same 5 bikes rack, and am looking forward to using it, I’m hoping the tailgate on my tacoma won’t hit it. I got tired of putting bikes in the bed of the truck and trying to find room for the gear also

🤣

Where do you get the kit??

You dont know how much I hate this video for wasting my time, is such an amateour move to make a clickbait video mate. 😡🤬 Just kiding bro😂 hahahha, I loved the video mate! Great work, very insight full, really well made, well passed, I enjoyed it the whole time. Also thanks for sharing the idea brother. Many blessing. Thanks!

Late comment but I love that you start with the real stuff, not knife material but does this feel okay in my pocket. So many multi tools fail that test.

You're funny and informative❤

useful info begins at 4:20

Alright I'll pick up another drop cloth

Damn brother im going in 2 months thats fucked

man this is some cooool stuff you make

It's sold out!😢😅

Staining oak is like painting walnut