- 3
- 2 647
Emmanuel
Registrace 23. 04. 2017
Does an 147k mile c6 corvette still make good compression?
In this video I went through a couple reasons as to why i think our corvette is not making acceptable horsepower. I give a quick rundown on what’s been going on with the motor, and sorta how to do a quick compression test.
As everyone knows. LS motors are pretty much bullet proof but I do have my suspicions as it could definitely be a tuning issue.
Car mods are: Ported gen X LS Heads, Stage 4 btr cam
As everyone knows. LS motors are pretty much bullet proof but I do have my suspicions as it could definitely be a tuning issue.
Car mods are: Ported gen X LS Heads, Stage 4 btr cam
zhlédnutí: 23
Video
Attempting to diagnose @yellow5oh’s Boosted Single turbo coyote
zhlédnutí 181Před měsícem
After deciding we should make a CZcams video attempting to diagnose @yellow5oh’s car, we ran into a few issues. After his tuner found a misfire on Isaac’s boosted 5.0 it turns out it was something on our side. We unplugged coils, spark plugs and tested them trying to see if the ecu will throw any other codes that could point us in the right direction. We later found it was a bad injector and wi...
Zr1 Widebody install on my BASE c6 corvette
zhlédnutí 2,5KPřed 10 měsíci
Hello everyone welcome to the channel, In this video I show how I installed my wide body corvette from JD corvette. I didn’t really go into any detail but comment down below what you guys need help with or hit me up on instagram @manny.lsx for any questions you might have when installing your widebody kit. Mind you I’m not a body shop expert haha!
Great work!
Where u get the fender liners for front and back?
Jd corvette from California, just call them up and let them know your plans!
So close
How did u mount the fog lights?
@@ImZiricuL this one is a good question. I found that this front bumper has issues with mounting the fog lights. What I did was just drilled a hole into the fiber glass spots and screwed it on with regular screws. It does not fit flush though. There is a gap. If u send me a messege on instagram I can show you what I mean.
@@ImZiricuL this one is a good question. I found that this front bumper has issues with mounting the fog lights. What I did was just drilled a hole into the fiber glass spots and screwed it on with regular screws. It does not fit flush though. There is a gap. If u send me a messege on instagram I can show you what I mean.
Where you get the kit I tried searching up that place but the zr1 doesn’t come out
You can search up JD corvette store and call them directly on google. they are out of California.
Is the rear panel the same as a grand sport or is this one wider?
Yes all the same zo6/grandsport and zr1
Hey so did you use an oem bumper?
No, but I reccomend an OEM bumper.
great job! How did you find fitment on the front end of this kit?
You’ll need a oem zo6 bumper for sure. And front fenders needed some sanding
@@Mannylsx yeah every where I am reading says oem front bumper just hard to source
Car is 🔥, where did you purchase the front and rear mud guards, have the same kite and cant seem to find them only for base models
Hit up JD corvette!
Thats my friend Pat Nohrs license plate frame !
Where you buy your rear wide fenders......?
JD corvette from Cali!
Love the build😍
Thank you good lookin
I’m proud son
Really hope this was pulled back apart to paint jams then put put back together to paint the whole car, I think it would look 100 times better with at least blacking out the halo and targa top or just go for full carbon
Thanks! And unfortunately, I took it to the shop as is. I regret not pulling it all back apart and painting it. It still looks great. The jams are nice. The paint shop did a really good job man. Later I’m gonna reveal where the paint job is from..
@EmmanuelC6corvette are those duraflex panels didn't look to bad as far as aftermarket fitment
@@jelenekoutdoors9023 they are directly from JD corvette. Not too bad. Fitment required so much DIY haha
Looks great 👍
Thanks brotha