Video

also no sound?

I can't find any video showing how to set the sixteen-channel remote, all videos always pick the easiest two remotes to demo. It would be better to make a video demoing the most complex remote.

No one tells you what to do when you can't roll the blind back up! Rolls down but won't roll back up :( :( :(

How deep is the frame?

This video is a lifesaver. Thanks!!! ❤

Please help. My blinds won't respond to the down button. I can use the down button to stop it from going up but it won't bring my blinds down anymore.

Thank you just what I needed. Where can I get that pin that slips in and out. Mine is broken.

When trying to set limits , by pressing set button on remote my motor does not jog I cant get the motor in this mode to set limits

this saved me from breaking our blind - thank you! So helpful!

They're not all the same, mine wasnt. Got it assembled but the chain still not working. There was a wire inside, unsure where, against the plastic, it went. Jammed when using

please help - my metal chain came out, when i try and take it all out and do as per the video, the chain doesnt turn and seems locked, please advise what i can do, thanks

It says that you slot the bracket in to the gasket seal but are you saying that you need to break the seal? My UVPC windows have sealing on them and there is no gap there. Does that mean that it won't work and if so are there any other options other than fitting proper shutters?

My blind only beeps it doesn't jog😢

Hi , Do you mean 75mm from back to front recess or left to right?

Thank you, you made it clear and simple, job done, well pleased😊👍

Remote shades, pain in the ass!

Hi @Louvolite, Thank you for the great video! I have a 16 CH remote shown in the video. Everything works well except it always goes to CC mode after being left alone for 5 + seconds. How to turn off the CC mode so the last selected channel will stay on the remote after I am done with operating the remote?

My blind is all messed up and although I’m following the instructions I can’t get to fix it

Factory reset does not wipe positions.

I have set top and bottom limits but it is still possible to move past them if i press the same direction again potentially damaging the blind . Am i not setting limits properly?

Oh mate you saved me so much time, thank you never knew my blind was made by your company too, not sure as it was 5 years old why I got a lot of blue that looked like grease on my hands?

Very helpful thanks

Sir How to reset blind by the remote?

great

What about the patio door handles ? do we need to cater for this or will the blind fit snug and touch the handles of the patio door?

Are they all remote controlled

I have the motorised version for 6 windows and the string holding the cellular are already broken for two of them. It is just 4 months I have them… the quality is definitely not there.

What kind of tape measure is that

What do you mean "Compressible / Not compressible seals"? Perfect fit

no sound!!!

Very very helpful

Chain fix for RollerBlind. In case you are here to reattach the chain for a Louvolite Shade System 40 clutch R3025, this is what you do Remove blind - steps to do this: - roll up blind (if you can with a little force, but not essential), push chain end in a direction it will move a little, usually up, push toward other end., it should now be detachable from chain end) Once removed, roll up blind if is not already Pull out mechanism on chain end from the roller tube - the whole chain enclosure mechanism should slide out - use a flathead screwdriver to ease out if necessary. Remove the plastic pin from point at the end, prise out with a small Phillips screwdriver in the hole if can't do manually Replace the chain - if it has a joiner the make sure it is placed close the mechanism on the side where the chain is chain is will drop down. Reverse process to refit. Note: the three lugs on the chain end should be faced upright, ensure blind is facing correct direction.

In case yiu are here to reattach the chain, this is what you do Remove blind - roll up blind (if you can with a little force, but not essential), push chain end in a direction it will move a little, usually up, push toward other end., it should nonkw be detachable from chain end) Roll up blind if not already Pull out mechanism on chain end - the whole chain enclosure mechanism should slide out, use a flathead screwdriver to ease out if necessary. Remove pin f om point end, prise out with a small Phillips screwdriver in hole if can't do manually Replace chain - if it has a joiner the make sure it is placed so where near the mechanism. Reverse process to refit.

Is the bracket are strong?

excellent video solution to a head scratching problem, thanks

Easy when u show how, thanks.

How do you ask alexa to open to favourite positions ?

Hi, are the blinds in a cassette or not?

I have a totally different made roletta blinder with a little bit different mechanic part, but thanks to the video it was starting forward to do. Thanks!

Where can I get a cost for these blinds

Hi @Louvolite, can you share how to remove unused channels on the remote so it does not appear during scrolling left / right? i.e. I only want to see channel 1 to 4 and hide channel 5 & 6 on the remote. Thanks

Hi @Louvolite, may I know how to set the remote to remove the channels that I do no need. e.g. I only want to see channel 1 to 4 on my remote when I scroll through instead of 1 to 6. Thanks

Hello, how to pair 3 blinds in one room so the upper and lower limit are the same on all 3 with the one remote.

Nice Easy Video, Definitely worked for my Blinds 💯

He doesnt even show it works sliding through afterwards. Ive re chained and it keeps breaking out!!!!!!

Thanks for the video. I was going mad trying to work out how to reattach the chain to the blind. Very clearly explained, thank you! 🙂

Many thanks for a short and very well explained video 👌🏻

Hi, Like the look of these, but how do you clean the glass once installed?

Or for permanent marker, just spray with deodorant (normal body spray, NOT anti-perspirant) and wipe with a normal cloth………then you wont have thousands of micro-scratches in them from a sanding pad.

How do you actually get the remote to work ? ( Mine has stopped but blue light’s working) Thnks