Video

Would have been great to get some video footages of the cameras, to see what exactly it looked like. Thanks anyways.

bad test...

very nice my friend, I plan to do sth very similar, it proves to be much more difficult than I expected 😞 which parts do you use, especially: fuel pick up, there is some sort of filter on it, vent, nice brass fitting.....

It is Worth...it is high quality your doing so high quality worth doing...good job man to you both you take care...

hello, Honda cr-v 2.2 noise in the area of ​​the pulley, remove the belt, nothing has changed, watch my video

That zip tie is going to snap after facing temperature fluctuations, vibrations and funky situations. I've seen similar fixes where folks found a way to wrap that seal with a metal band of some sort. Think keychain ring (saw someone actually use this) or another study but bendable length to wrap around and leave enough on both sides to pull right and then snip if the excess

It's a quick job to waste time and money. Your new brakes won't last even a year. No rust cleaning, no grease, keep it like that ! 👍🏻

You should have more views. You fix things in interesting ways.

Good video mate, music was annoying so turned the sound down ,also i got the idea of the worn chain tensioners no need to labourthe point really. Otherwise good 👍 Regards uncle Franko

Congrats and welcome to the 3d printing community! May the plastic spaghetti gods be kind to you and bless you with perfect first layers.

I forgot to say to disconnect the battery before you unplug the under the seat wire harness. Make sure you have the radio code.

Zip tieing the boot doesn't seem right. In compressed state it could puncture the boot again.

Please help me, i want to know which contact push the button on control panel

Please help me, i want to know which contact push the button on control panel

Hello, can you help me please, give me your Facebook link or what'up.

Hello i see that it passed 3 years since this video was posted, how is this chain brand did you have any issues since the change ? what oil tickness are you using ? Many thanks !

Neat little video, but you didnt need to colour match the ethernet wires. I've used a standard Cat 5e cable to extend the remote. The colour of the wire is irrelevent aslong as the pinout is the same :)

👍🏻

very useful video

👍

Multumesc cu ajutorul videoului tau am reusit sa inlocuiesc distributita, garnitura chiulasa pompa apa si segmenti, desi nu sunt mecanic . Multumesc inca o data si astept mai multe filmulete .

I've renamed this video to "how many ways can I lose the tip of my finger" :)

i need the picture for rear support shockbreaker of statlet ep81 , is that defferent with starlet ep70 or the same part ..thanks ...

It is perfect guide "how not to replace pads". You haven't used an ounce of grease on the brake pads and caliper pins. You haven't cleaned the rust off either the caliper body or the calliper bracket. You did not remove the dirt from under the brake piston seal and did not lubricate it with special brake grease.

Best video I’ve found on CZcams, thanks

Nu se aud Explicațiile dumneavostră

Hi, did you figured out the scratching sound in the end of video?

Hi, nice video, so should be 2 tensioners when comes full kit right? I think i should change too , i can hear chain on my 8th gen civic with 207k km.

Hello, good work! 🙂How did you loosened oil pump and camshaft sprockets? Thanks.

Not injectors engine starter week i'm did that yesterday and im don't have any problem with start the engine.

Hi i'm have the same problem in my honda CR-V mk3 2.2diesel and i replecment yesterday engine starter and my problem is gone. I don't have to replecment timming chain kit.

thank for your video 26-12-22

Twist the injectors

Multumim. Ar fi fost super daca ne aratai si cum se pune la punct distributia si aici ma refer la PINION CU VARIATOR DISTRIBUTIE ai taiat ce era mai important . Poti sa-mi spui o parere despre kitul de la ASHIKA?

Cum e dupa ?

Omul meserias dar nu merita atata munca o vechitura ca asta doar pasiune fara limite.

Daca placile de Pb sunt in conditii bune,atunci cu siguranta schimbarea electrolitului va prelungi voiata acumulatorului! Atentie! La reincarcare,amperajul curentului de incarcare ar trebui sa fie de maxim 10% din capacitatea acumulatorului! Timpul de incarcare poate ajunge pana la 10 ore!

I have a Faria multi-function set (2) 5" gauges that are no longer available. i'd love to fix them. It looked like you had some sort of shop manual that showed resistance levels etc. where might someone find such a book? great video!

Lleva intercooler o no lleva?enseña algo más detallado

It is very dangerous to make a fuel tank out of fuel regulator gas can as the can is no stable and because it doesn’t lay flat like a normal marine fuel tank

So I got a 2012 Ford Taurus and my boot has like completely entangled it's self but the tire rod is still tight and good am I good to just replace the boot? Thanks!

5:16 che sigillante hai usato?

Salut..ce tip de ulei folosesti la motorul asta?

Cind se pune apa distilata se golește acidu sau nu

Can you tell a partnumber of that DMF conversion set?

Salut vad ca e civic mk7 , cum ai scos oglinda fara sa o spargi , am aceiasi problema mulțumesc!

This is such a useful video. Thanks for sharing. I would love a list of components used and the glue / sealant too. So many engines get run on old fuel because 5 litres is put into a 23litre tank and only 3 litres is used. On the next trip the fuel gauge says it’s nearly empty so another 5 is put in and so on. A % of the fuel is likely to be months if not years old if the tank is not cleaned routinely.

Such a vague video. A lot of skips, no idea why you didn't film it.

Référence merci de amortisseur