Video

Rob, I am hooking this boom mower up to a SLV75-2 Kubota. Your demo here uses one connection adapter to hook up the mower outside the cab , but you describe a joystick inside the cab as super controller , where did that come from and was the 14 pin adapter ( normally has 4 pins stock ) adapted for this mower ?

Thank you for sharing!

Great video could you give me some info on? Why am I bobcat stump grinder moves way too slow going left and right but up and down it’s fine.

How did you wire it to the 14 pin or 8 pin connector? I have a sweeper broom from wolverines that I can’t figure out. It has the same setup as this.

Thanks, that was super helpful info.

I'm dealing with this in my '91 Buick Century now. The terminal for the inline pump fuse had a bad connection. So I changed it but I'm still having issues with it. Can anyone tell me if there is a way to crimp it down with the tools I already have and if not where could I find a crimp tool for less than $75 ??

Hello, does this work to connect a bobcat attachment to a John Deere Skid loader? both have 14 pin harnesses with 7 pins installed, but not the same layout. Thanks

is this harness jumper made to switch regular high flow to xps high flow on the actual machine to be able to run certain attachments?

Where can I buy one?

Liked, Viewed, Shared, Subscribed!

Ridiculous!!

Where can I purchase the tools to remove these pins?

I just mounted a 5Ah 12 volt battery right on the mixer

do you have the full pinout for the JD skidloader?

Did anyone else hear the radiation noise around 8:00

Still available price ?

Great video, thanks❤

Great video. I recently acquired a Kubota SVL75-3 and have this grinder in my fleet. I was already able to hook up the machine, the 14pin connecter and successfully run the SG60. The only issue is that the the functioning of left/right, up/down, extend/retract is backwards on the joystick controls. My hope is to NOT change out the harness you're showing in this video and just switch the existing quick connectors on the solenoids as you did in the video. Shouldn't be a problem, right? TIA for any reply!

Bobcat S630 horn wiring location tell us

Thanks for the video. Im renting one of these for the first time tomorrow ans was wondering how to operate it. This little vid makes perfect sense.

Do u have kits to wirelessly control takeuchi TL26-2

Does anyone know what those electric pins are called?

Can't hear with machine running.

Can you use the 7 pin connector to operate the solenoid valve?

Great video! Thank you

Can't hear you

Connector manufacturer: ITT Cannon Connector part number: TNM6S14-0304P1L Optional heat shrink adapter: TNA14HSAD-00L Thank me later 😎

Wouldn't it work/make sense to simply jump the connection between A & B -- allowing it to them work with attachments configured for either standard.

Someday it's gonna be real cold in that not sealed tab

How would I hook up a 2000 model 863G with a controller? I want to buy a stump grinder attachment as I have a lot of stumps on my property? Any suggestions? Thank you.

I feel so dumb. Bought a Wolverine Cement Mixer brand new off auction sight unseen and didn't realize these things weigh empty 700 lbs. All I have is a Bobcat 700 witha lifting weight of 1000lbs.

Ever get any of those sold

How can I figure out if the controls on my left joint stick work cuz I have a seven-prong plug I want to wire up to a stump grinder but I can't seem to get it to work

Do you make a 7 pin Bypass harness?

So much complicated lol just want to get my plow hooked to kubota

I have a older model grader with the valve body on top. Nice old grader but your vids have been nice getting it working on my 333g John deere. Nice vid!!

No information in this video

Nice I will check coils on Bobcat S220. The combo bucket will open but it won’t close, hope it just simple coil.. Thank you for the great video

Wiring diagram?

Buenas tardes mi hermano me podrías colaborar las conexiones naranjas en que parte del harness del bobcat S185 se conecta muchas gracias por tu colaboración

Hi hoping you get this message , I got a bob cat 773 and the control for the shut is not functioning.. I think we're missing the wiring harness do you sale that?

Hey man great video one question do you know where can I find the 2 pins plug separately?

Overpriced for what you get!!! Lol. You guys charge just as much for your kit.

Are you still using your mixer.

Nice information thanks...

Did you work on a Landhonor concrete mixer? I need parts. Lmk. Ty

can you tell me where the fuse box is on 843 model bobcat

Thanks for sharing this story

Using that blue scotch lock is not a great idea

These videos are 1000% awesomeness