Video

The pump you used 50? And the pulley 30? or what please? 🙄

Additionally.........After the EPB brake is released remove the power connector from the EPB brake caliper.

Hello, I have the same problem, are you forced to remove the strap to disassemble? Can't you leave the strap and remove the iron casing? Nice job !

Mesh eye pro 🤮

where can I buy one without having to spend $500 at the dealer? I can't find one anywhere.

you might brake the caliper by doing that

Did you have to get it reprogrammed from Toyota

6:37 was it even a Yaris all I could see was the brake hub, total waste of time

You need a lesson in camera use

My handbrake is not working. It goes up and down but is not holding the car. I have a 2012 nissan tiida sedan. Does this video show the solution to the problem

thanks for this good instructional video. Thanks to this video I can now do the job myself.

Would just be the tensioner needs replacing

The creativity levels are off the charts.

Dodgy as fook. 😧

The camera man had one job 😬

Do I need any system setting by computer after replacing the blower ? My car is 2009 520d .Thank you for this sharing.

I wanted to launch my Toyota Avensis, press the brake then accelerator and it just snapped.. it's going D, R but doesn't move. When I put it in D it makes some noise for like 3sec. So can someone tell me what should I do? 2.2d 150ps 2010

it's possible, you just need to align flywheel to bolt holes 😊

This really helped. All the other videos tell you to take the whole door interior panel off and mine was stuck. Managed to change my mirror following this. Ford C-Max II phase 1. Thank you!

Hahahaha! Love it!

You wanna try that again with the camera in focus and proper lighting?

What is the other end connected to ?? Where does it go ?? Not helpful at all ….

Dublin bus mech is watching so i was informed

can't believe I didn't find this before. just done this job and what a nightmare this is. I would advice whoever doing to have extra set of studs and nuts just incase you break them coz I did. impact wrench and various extensions are must. if you have access to a ramp it will make your job 10x easier.

Pepito big time youtuber 😂 Which city are you in?

You will watch

My check engine light came on yesterday and this was the problem. How serious is it? Should I be worried? Can I drive it until next pay day

What part numbers

Hello, is this a gear box oil change for suzuki swift with 1.3 liter petrol engine and 5 speed manual transmission? if so, i wanted to know the size of the tools ( bits) used to remove the filler plug and drain plug Thank you :)

Wow..ganun pala un idol..thanks for sharing

ano ginamit mo pang linis bro ?

Sorry sir i have the same problem with my cla c117 . I need to replace all the egr or just that plastic (vacuum valve egr ) ? If you give me one advice i be thankful 👍

its most probably a blocked cat/dpf causing the high fuel consumption and not the 02 sensor

Go to farm . Is not for you this job

!!!!!!!!!!!???????????????

could it make any vibration at idle also with this noise? I've vibration problem with my 2017 Corolla. Looked everything but didn't find anything except this one.

Hey, I've uploaded two videos on my channel for you to check on the DPS6 and am needing your advice man. This would help tremendously as no shop wants to take the job on this transmission! 😢

idol saan location mo?

This is very good video 😀😃😄

This video has fukn so many fukn fukns I lost fukn count

Fucken worst video ive ever seen, shit music

Hi Where do you got timing belt kit?

Did mine this afternoon. Thanks for your help 🙏 From Angola, Africa

Nice

Same problem man..I changed recently..it again out of order..it's manufacturing defect

New subscriber here! Nice to see a good pinoy mechanic here in Dublin. Bisaya pa gyud! 😊

What a load of crap

This is a joke

Good video.

Nice one buddy I just watched this because I needed to no how todo this job as oil was getting into the cylinder where the spark plus is and making it misfire do you which cylinder cylinder 1 is ??