- 11
- 73 831
Rx Arms Solutions
Registrace 17. 03. 2019
Beretta 1301 Charging Handle Removal and Installation
rxarms.com | How to remove the Beretta 1301 Charge handle and install the RXARMS Titanium charge handle.
zhlédnutí: 484
Video
Rx Arms Tavor X95 Pistol Grip (and Tavor 7) Installation, FAB Defense Tar Podium Bipod Installation
zhlédnutí 7KPřed 10 měsíci
www.rxarms.com | Removal of the OEM IWI Tavor X95 Pistol Grip (and Tavor 7) and installation of the Rx Arms X95 Pistol Grip (and Tavor 7). Installation of the Fab Defense Tar Podium Bipod.
Benelli M4 Rear Sight Half Moon Installation
zhlédnutí 951Před 10 měsíci
Removal of OEM Benelli M4 sight, and installation of Rx Arms Rear Sight. Get yours at www.rxarms.com
Benelli M4 Magazine Extension Tube Installation
zhlédnutí 21KPřed 11 měsíci
www.rxarms.com | Removal of the limiter, replace and install with the Rx Arms Benelli M4 Magazine Extension tube to increase capacity of your Benelli M4 and M1014. Available in Custom Dark Charcoal for Black shotguns, or Titanium Cerekote for the Benelli M4 H2O Magazine Extension. 00:00 Intro 00:16 Prove Gun Safe 00:34 Barrel Removal 01:13 Limiter Removal 01:27 Retaining Clip Close Up 01:42 No ...
Benelli M4 Storage Compartment for Collapsible Stock
zhlédnutí 1,1KPřed rokem
Get yours at www.rxarms.com
Benelli M4 Bolt Release Tab (komando P4, Canuck Operator, TAC-12 clones)
zhlédnutí 11KPřed 4 lety
Get yours at www.rxarms.com Benelli M4 Bolt Release Tab Benelli M4 Bolt Release Tab made from 1095 hardened spring steel with a Cerekote Graphite Black finish, the same finish that is applied to the Rx Arms Benelli M4 Titanium Charging Handle. This modification is very easy to install, requires no gun smithing, it just tucks in between the forearm and the forearm retaining band. Also compatible...
Canuck Commander Defender Regulator +1 Tube Extension
zhlédnutí 17KPřed 5 lety
You can pick yours up at www.rxarms.com A 1 tube extension designed for the Canuck Commander, Regulator and Defender (and all 14" models they currently offer). This will also fit onto the Dominion Arms Kodiak 13", Churchill 12" and 15", and most other turkish shotguns.
Canuck Commander Defender Regulator +1 Instructions Video
zhlédnutí 3,5KPřed 5 lety
For another video with a gun that has the same tube internals for cutting your tube for an extension, see this one here, he explains it very well. czcams.com/video/u2OhofpznY8/video.html
Thank you, very helpful
So with my benelli m4 colapsable stock, I cannot unscrew the recoil pad because there are no screws visible to unscrew. It this rear mount doesn't work for my stock, what options are available? Thanks
@@StevenHenein I’ve contacted you via email, but yes there are screw’s they are just hidden, need to stick a Philips screw driver into the 2 dimples on the recoil pad.
Thanks for your products and your educational video!
Where did you get that heat shield?
That is our heatshield, it is a prototype, the final revision should be available in fall 2024.
I need that Benelli m4 heat shield already! 😁
What heat shield is that?
It is a prototype version of our heatshield, final version should be out in fall 2024.
Anyone know if the installation is the same for a Beretta 1301?
yes it is the same process, it is the same rear housing design.
Is that heat shield compatible with ScalarWorks sync mount?
No, it need an RX mount as part of its rear attachment point.
@@rxarms3639I saw an updated version of your heat shield on a forum, is that the one that will be coming out this year or the one in this video?
@@sogebk final version is different than this one.
@@rxarms3639nice cant wait, very pleased with the titanium charging handle and bolt release tab 👌🏻
I already bought it, this got to be the best QD mount, better than IWC QD in my opinion. looking forward to lube my screw driver lol!
Thanks for calling it an installation instead of the annoying "install."
IS THIS LEGAL IN CALIFORNIA
How long is the current wait for new stock?
Any chance of thede coming back in srock? I have a Folding Enforcer that I'd love to see a hold +1
Nope
Cant wait to install on my x95. Thanks for making this.
Just ordered today hope it fits my mac 1014
With all due respect there are cutlass grips, pistol grips and then there is what you have. Yours is a Hybrid grip. Calling it a pistol grip when it is clearly different is incorrect, misleading and shows a lack of imagination. The Hybrid is unique & superior due to the addition of the podium. Own it.
I must say this is a high quality piece of gear. The color match on my black X95 was great, and the fit was perfect. The Podium fit perfect just like my Tavor SAR. I originally wanted the IWI pistol grip, because I like the standard trigger guard. However, IWI was out of stock. That turned out to be a blessing in disguise because it led me to this and I am very happy. I am the type of guy who likes to have extra parts on hand (charging handle, bolt parts, etc.), so I ordered an extra for "just in case". Highly recomend.
Thanks for making this. I just got a Canuck Folding Enforcer and plan on doing a +1 extension. Just planning out whether is was possible and it definitely looks it.
Is there any advantage to putting the retainer spring clip back in, (other than spring retention during disassembly)?
Couldn’t understand directions. Now I have a hole in my ceiling… To be honest that mag spring buffer sucked ass. I had to use a pair of vice grips and crushed that bitch to make it go back
ya that spring retainer can be tough to remove sometimes!
@rxarms3639 any updates on 1913 rails?
So, with the tube extension added the spring retainer clip is no longer required?
You can still use the spring retaining clip, or not use it, it is up to you. If you do not use it, the spring will rest against the mag cap.
How long does it take to ship a order you guys haven't given me any updates
We usually ship within 1 day. Check your spam folder, or contact us directly if you are having problems with your tracking.
Why are you making the firearm non-compliant with 18 USC 922 R?
I'm not sure what you mean. For one, I am in Canada, secondly, I removed the magazine extension after the video was recorded. Also, this +2 magazine extension does not help with 922(r) even if it was made in USA, doesn't matter if it is made in Canada or not. Thanks for your input.
@@rxarms3639 Ah, in the US, the 922(r) compliance has to be replaced with components made in the US on a foreign firearm. The whole magazine tube would need to be replaced after replacing 4 existing components. I had to do it on my M4.
@@BryanKelley1998 as far as i understand it, there are many other USA made components to choose from for 922(r), one doesn't need to replace the full mag tube, and can use a +2 mag extension which is much easier to install. Secondly, I have read that 922(r) only applies to the importer of the firearm. Once it is in the USA you can do whatever you want to it (going by what I have read). This is not legal advise, and I am not a lawyer.
Will this fit in the PANZER ARMS M4 TACTICAL SEMI-AUTOMATIC 12 GAUGE SHOTGUN
This will NOT fit the panzer, it has a different length needed on the end of its main magazine tube.
Wow, this is a HUGE improvement. I can finally shoot trap and skeet with ease, due to the uncluttered sight picture. Thanks for making this!
I can't wait for that heat shield to become available. Very awesome.
It is ready finally, i've been fine tuning the design for over a year, and I can say that I am now happy with it. Fall 2024!
I saw you did not put the spring seal cap back in the magazine tube. Will the spring get damage when I put rounds in the tube?
I was just showing that method for demonstration purposes for my USA customers. The spring will not damage the cap without the retainer, as far as I am aware. It has not damaged the Titanium Mag cap at all.
922 compliance states that this is a felony 😅.
From what I understand about 922(r) (I am from Canada, so this is not legal advise), is that as long as you switch out some other components of the M4 with american made, then it is just fine to use this mag extension. But like I said, I am not a lawyer, and this is not legal advise.
Where to buy the extension? And especially is it legal in Florida?
You can buy this extension on rxarms.com, check your local state laws for legality of this extension.
Will this work if I’m running an agency handguard??🤔
Do you do work on Benelli M4's ?? I seen in one of your Pics on your website that you eliminated the Rear Ghost Ring Sight and had a Red Dot in place AND IT LOOKED AWESOME... I would love that set up !! Do you do this kind of work ??
This +2 mag Extension would be NON -Compliant in Canada correct ?? I have seen Mag Tube Extensions +1 for Canadian Compliance...In other words with +1 mag ext. ... 5 - 3" shells in the tube would make it compliant with Semi Auto Canadian Law ?? Am I missing something here ??
Yes this is correct. For Canadian owners, they need to plug this tube first before installing it on their firearm.
Great video. My RX mag tube extension is already shipped, should be getting it any day now 🙂
That benneli m4 looks like a brick
Almost all the aftermarket parts I've used(and spent almost as much for as the gun itself) have at some point failed in one way or another, optics mounts, sling clips, and folding stock,but especially mag tubes. I had a buddy make me a one piece extended mag that gives me 8+1 3" capacity and seems to be holding up very well after 250 rounds. Other options for this series are limited and and of questionable reliability. I'm seriously considering going to a Beretta 1301. I like the M4 alot but,it is limited in upgrade options and their durability is questionable with hard use. The only other ( very costly) option is to have each item custom made since factory upgrades are basically unobtainable here.
I have some of your products. Good stuff. Find someone who can CNC wood furniture for the M4. A shorter wood stock would sell.
I have actually had this on my mind for some time. I might look into it in the future..
I’m looking at buying this mag extension but can’t tell which color goes with which picture. I’m looking for the same color as in this video, is that the dark charcoal cerakote or the titanium cerakote?
As per website description, Dark Charcoal is for black shotguns, Titanium Cerakote is for H2O shotguns. Thanks!
Rob, is that collapsible stock still available on or for any specific US models? Benelli only shows it as fixed on civilian models now.
The collapsible stock comes standard with the M1014 in the USA. But in order to fully collapse it, you need to buy a new recoil tube such as the 6 position recoil tube I sell. The Benelli M4 comes with a fixed stock pistol grip in the USA.
Do you have any nickel coated mag tubes? I was thinking about getting the Panzer M4 marine version
This mag extension is not compatible with the Panzer M4.
@rxarms3639 Anyway, you can make one for the panzer? For us poor folks lol
Just got the new 11732 gen 2 benelli 4, my 5 position stock looks like it has a spot for this mount but I have not taken it apart yet. Do you know if this will work for the new gen2 5 position butt stock with the redesign?
Unfortunately, it is not compatible with the supernova stock (that the 11732 uses).
Perfect. Thanks for taking the time to make this video. Looking forward to getting a few goodies from you guys.
Cheap shit poor quality,falls apart
Will you produce the heat shield without the key in interface with the optic mount? I'm sure some users may already have different mounts for optics already installed, so with that interface deleted, the heat shield can fit a wider range of benelli m4's
the support at the receiver is a necessity for the balancing of the heat shield. So unfortunately the design will require an Rx Arms optic mount to be compatible.
Awesome. Thanks for posting this. I was reluctant to buy the +2 extension as I didn't know if the barrel rings would fit over the hump. Looks like its no problem so I'll go ahead and order it. Great video!
Yes absolutely, we engineered this to take down the gun without removing the mag extension. Thanks!
@@rxarms3639 I been reading some extensions won't thread proper.. what brand is this that you have ?
@@justobey733 this is Rx Arms brand!
What about getting even bigger bigger gun's you sorry sorry mad people's
Believe in the lord Jesus christ. Only then you will be saved. Love from England where only the authorities have guns.. Good luck USA ,WE THINK YOUR GONNA NEED IT ❤👍
Canadian detected
eh?
Will this M4 operate fine without the retaining clip replaced ?? TY
Yes, from much feedback I’ve received it functions great. Since I am in Canada, I only run the gun with a plugged canadian legal extension.
Is this a new product? It looks pretty much the same as the stock grip with the fab on the bottom which I’ve had for 10 years now on my T21 build… I must have missed the point of the video
Our grip is for the X95, and Tavor 7. The FAB podium does not attach to the OEM grip supplied with the x95, and T7. Our grip gives compatibility to add the podium to X95 and T7. This video is unrelated to the Tar 21.