Video

For me it was the simple replacement of 5 amp fuse

Where's the reset button?

How do you turn off rrunning lite

Hip muscles are very weak as well

Thank you so much for sharing the above. I wanted to gather information as to how to both get in and out of the wheel chair. Reason being i am short as well. Lack balance issues

If the battery isn’t taking charge at all, what are some of the solutions?

Greeting How is my control of my chair, water fell on Qantúm where it is charged and I did not realize that it was wet and I put it to charge and now it tells me on the control screen configuring the network and nothing does not work What What can I do in that case, please, I would like you to tell me.

I Need a new joy stik for my quantum 6000Z

I need a joystick

Excellent video! THANKS!

If your chair is still in lock mode turn it back on press your horn button twice if you have one on your chair, then press your joystick to see if your chair will move.

My chair is in driver lock mode and i have tried everything and i can't get it out. I tried the turning it on and tapping the horn 2 times and that didn't work either. So can someone PLEASE help me out...

Hi anyone have an idea where to get a mirror for a scooter 🛵?

Love, love love the gravel part! :oDDDDDD

System Lock

My chair still will not come out of lock mode. The charge lights just keep going left to right. Tried everything, it will not come out of this mode. The yellow button flashs like yours. It's fully charged.

I have a Permobil power chair and it has a low turning radius,turns into bed, raises so you can get something off a top shelf while shopping lots of features you can add.

New subscriber sir always watching your videos very helpful❤

What if it’s moving very slowly?

If a chair moves slowly and backs up fast, where could the problem be?

My battery's are good but I get no power to the joystick it just won't turn on it dose nothing. Any suggestions?

We bought a used one. Is there suppose to be a cover along the length of the rail to help hide the greasy gear.? Thanks

Thank you for your informative video. What might be the issue if my seat is not elevated but I am still getting the red x ❌ and the chair isn’t moving.

Our Open Sesame has a loud thud when it closes and connects with the lock. And constantly bang bang bang bang and we can’t open it with our handle when it freaks out - the handle will lock and we have to keep hitting the touch opener on the wall to get it to finally stop. We had high expectations to help open the door. Anyone with a hearing disability where they panic at sounds will not like this. Imagine the sound to this door louder than in this video and like a screen door slamming at impact.

Please send me WhatsApp number. I want to share you wheelchair keyboard troubleshooting so please help solve problem wheelchair

Looking for a scooter like a go go in red I have a j6 but would like a scooter

This helps. Ty

Sir, I’m sorry to be a pain, but I have an idea, but I’m not an expert or that knowledgeable to come up with what I need. If a caregiver needed to retrieve my chair from another room, and I could write a, “Cheat Sheet”, for them, or perhaps laminate The first few steps; like 1-5, so they could move/drive my chair back to beside my bed, so I’m able to take command and tranfer myself, from my bed to my chair.

Sir, thank you so much, for taking the time, in a few short minutes, to explain the fundamentals to get moving in this chair. You couldn’t have done any better!👍

does anyone have a videio showing how to use the joystick in the back for caregiver?

On some of the 4 wheel models there is a battery release /lock handle under each battery ..older modles

Need help with menu (settings), and no help was given.

How do change languge

Necesito las instrucciones en español. Gracias

Were is the battery located on a pride chair

my joystick won't charge. is that a joystick problem or a battery problem ?

First I need to see how yo.properly hook up two 24volt batteries to a quantum rival wheelchair and also need to see how the controller works. The chairs functions

cool

Hello wondering if you can help with troubleshooting this chair lift?

Good evening, I bought a 1313-4331 OEM. But I can’t communicate with Qlogic 3 and also with Aneble50! I need some help, what do I need to do? Is it necessary to update firmware or other additional information as well? And how to get an account number to access the equipment information? In my case, the system is not starting, it just says “CONFIGUGURING NETWORK” How to get it. Here in Brazil it is Impossible

Had to move the lift because we put new carpet underneath. When we put it back it doesn't work at all. Is there something I need to do to reset the lift?

2:35 anyone know why mine only goes from seat and seat and back? Not just back

my Bruno 2110 CRE is making random stops in the same spot ... any ideas why or how to correct ? it is about 6 years old and the first bit of trouble we have had ............... it has been so ever reliablr

Really helpful video, thanks.

Is there a way to lock the controls. I have kids around and sometimes they think it's funny to drive off on my chair. We're talking a 5yr old and a 7yr old. I need to keep them safe.

The second one M300 is showing a lock on the screen

I have a problem with my chair, which does not drive, it says charger inhibit error. What can I fix it

I’m thinking of getting a power wheelchair instead of a scooter. I need to know if they have a key like the scooters so I can keep kids off it when I’m not around. And where is it located? Thanks !

our Acorn stair lift, by accident caught on a small door knob and caused tilting of the seat - thank You for your input :) Moe

I have a Bruno SRE-3000 that gives a beep whenever I try to move it I paid a company $150 to come to my house and fix it he spent a short while making it beep then told me he didn't know what was wrong, but it could be the circuit board at around a $1000.00. but didn't know for sure if that would fix it. I live in Oklahoma where there is very few repair companies, do you have any suggestions? If I disconnect the sensors one at a time that can go bad through getting dirt or dust will the stairlift work or do all sensors have to be connected?