Video

In 1981 I come from brasil and my first car in the USA was navy blue, black roof 2 door ford torino that I bought for 150.00 dollars at the time, work fine but burning a lot oil.

Is that a 70 Chevelle hood. ????

302-2V Thats not 2 valve fellas its 2 Venturi

As a blind man, this video made me feel very targeted 😂

That does not match my friend.

I have a 1949 I was 4 yrs old when I road home in in 1949

Why don't you put bigger tires on that would keep your RPM down that way no changeing the gear ratio

That’s a bad ass car 👍🏽

I would just buy another, they're cheap these days especially in manual

Nice. I have a '52. Used the gas tank from a '48 for underbed location. Works fine.

That sucks that the invisible bra ended up doing in the bumper and you weren’t able to see the fruits of that protection

Do you believe the Honda 2003 ex will be considered a classic?

Sold

What a flash back ! Had some fun in that car .

Enjoyed the video and interview with Fred! I owned a '79 when I was 16. Now at 54, I picked up a '83 a few years ago. The appreciation and love for these cars is something that has stayed with me all these years. Thanks!

They are still a beautiful looking car .

Your brake caliper needs rebuilt if it is wearing your pads uneven. It's hanging up and not releasing properly

Click on the related link to see the full video on how to replace the rear brakes on your Honda!

have soft spot for this generation, have owned two

Slide pines the one up top is not functioning properly pull apart and lube only the side not the tip

The pads look OK, the score marks seem unusual it indicates something is trapped between the brake calipre? Strip of the break pads and do a visual inspection. the brake piston could be damaged, or a retaining clip caught between the brake bad and the plate. Use a torch. Good Luck.

Looks like a rock was inbetween?

You can take the pads off and place a piece of sandpaper on a flat surface and sand the pads in a circular motion, make sure the surface is actually flat like a tabletop dont use an agressive sandpaper because the pad material is much softer than people would expect. Its not making even contact and those stripes of rust are just carving grooves into the pad and transfering that again to the rotor itself makint the problem worse, sand the rotor as well maybe even take a wire wheel and buzz it good to clean all those slots. Also you have a "drilled and slotted" rotor which requires more attention and maintinence than a standard rotor

Not to mention a junk yard😂 all the piping in the work and for what you need it will cost you 3$ and a grinder or a sawzaw blade but hey if it works it works, you just taught me something that I thought would surely break

Literally seen a pile a steel and galvanized steel piping at least 10 feet tall today at Home Depot, that to expensive for you? Go get a 3foot 2in ID exaust pipe from autozone for like 10$

If you have to change the other side, then you have to change this side regardless of whether it's in good condition or not. You always change rotors in pairs so that your pads wear evenly

I'm sorry a PVC pipe is not going to break your lug nuts is already pretty broke

Any idiot saying lead pipe was a good piece of breaker bar pipe is a fking idiot. Lead? The softest metal of all time? 😂😂

Click on the link in the description to see the full video 👍

I use handle handle from one of my old floor jacks.

If you have a floor jack most of their handles work that’s what I uaey

You can buy metal pipe EVERYWHERE

The same Phillips you'd use on door hinge screws👍🏻

Not sure what this guy is going on about plenty of metal piping at my local lowes

Fence post or top railing can be bought at Lowe's

What's worse black people or law enforcement?

Try one of those garage door motor drive shaft. It comes in 2 pieces. It’s strong, Just the right length and it won’t bend

Click on the related link in the description to see the full video

If it's a Japanese car, it might be a JIS screw, not a Philips. Philips will strip out a JIS.

They are generally no.3 Philips

Alot of them are pozidrive

What in the cheap knock of rotors? Prefer mine with veins

Click on the related link in the description to see the full video 👍

just be a man

Cause ur buying cheap 5 mil glove jump up to a 7 mil.

Mine was in worse condition than this, but 90,000 miles and not much to replace besides the alternator and the junction box. After a bunch of bolt ons i’ll be painting in about a month and it’ll finally be back on the road

Click on the related link in the description to see the full video 👍

Totally unaware disc brakes had shoes. Thought they were for drum brakes only and pads were for disc brakes. Thanks for the info.

Never seen brake clean used the right way, weird

Do you think the savings might be offset by the toxic brake cleaner that you just sprayed into the soil?