Video

Mine didn’t come with a recipe booklet to explain which settings to use for what. Can someone help me out?

Narration with a Canadian accent czcams.com/video/A9wHkb9gVCA/video.html

Narration of the Original Jimmy jig by a Highland lassie czcams.com/video/p9p04fgZRl8/video.html

See here for what was copied by the BIG BHOYS czcams.com/video/VBkG16RVq94/video.html

How bearing works here?pls explain,

منشار منزلق طاولة منزلق

Thanks!!!

👏👏👏👏

This is the Original rack and pinion on the Original Jimmy jig see here czcams.com/video/VBkG16RVq94/video.html

Where do you set it for toast. It has nothing about toasting in the manual.

Paint first before attaching ,with latex paint only, and calk all with latex calk at all joints at wall head

hi, very good idea ithought of this over the bay window in my bungalow,. thank you very much ..

Concrete? I’m a bit lost

The code in my area should swing inside for safety

Love the music but from 4 minutes on the video goes blank

Great review

how do you make toast in it?

Every power tool in the shop, to make a stick.

Nice idea!

Aye I know that , software, problem occasionally

Fyi, the last half of the video is blank! :o

28 DEGREES C

Aye Ihave one on the 3leggit saw horse

Love it. Have you attached one to your 3 legged sawhorse? Great ideas, keep em coming, your an inspiration

Depth of cut one and three quarters inches

Hi. Whats the cut with a 7 1/4 blade ?? Thank you

I;m doing thesame thing too i have a brick sidind. good job😀

ᵖʳᵒᵐᵒˢᵐ

interesting product which I may use for another purpose as an overhead camera device... using the horizontal/vertical axis rails upside down for fixing a high res Sony camera to shoot from 2 to 3 meters up down to a plane of 2 by 2meter with a 50mm prime lens... using it to be able to fine tune the camera position... (the camera will be raised by wind-up system) Now this nice device is not entirely documented... as I need to fix a chosen or slightly changed position ... I see one screw to fix on the sideways (X) axis, but not a similar fixing screw on the forward/backward Y axis.. Is that correct? If so...do you think it would be possible to add such a screw by tapping a hole in the Y axis part? I would be grateful for any reaction Tjebbe van Tijen

why would the wood get stuck in the antikick back pawls?

Déanta go han-mhaith....

see under for the build videos how about some comments

czcams.com/video/XkpGa0hSssQ/video.html building the mould to shape the gramophone record using a kitchen oven

czcams.com/video/_Z7UBRLYHcI/video.html the horn build sound bar to amplifiy

czcams.com/video/gHgkgmP0gLI/video.html the build of camera slider from a drawer slide

why do so many people like these videos. they are not well produced, not easy to understand.

𝙥𝙧𝙤𝙢𝙤𝙨𝙢 🌷

Just like a Fine Homebuilding illustrated tip in 1981 issue 3.

Mealthy Malathy

Me ayudaste mucho

That router is so loud I can still hear it 10 years later here in 2022. Nice sled design for that purpose though.

Thank you

KISS Well done

Ok

Aye, who copied it first then the rest copied the first but this is the first rack and pinon and was used on the Original Jimmy Jig , when their fences exit the table saw top that is a jimmy jig, the jimmy jig has a rip width of 4 ft plus, many more inches and superior to theirs

the only fence that stays put, will never deviate from parallel because it is fixed along it's length to a sliding table, now do you understand it simply the best because it answers the table saw's short comings, most table saw fences have had that problem since the inception of the table saw, macduff fixed it for good

Wow

Yep

Now do it with stucco 😖