Video

bought some expensive tools that come with life time guarantee. broke my breaker bar trying to get that bad boy off and all i thought to myself was “thank god i splashed out”

Top bloke 😎👊🏼

Did you install a distributor or just cap and rotor

Thanks so much for this video! I am about to do this in my LR3 this weekend. If you're in SC drop me a message, would love to meet and greet with another LR fan! (me, at Greenville)

What about the brake lights the actuator doesnt effect the brake lights

I can’t get the Starbit T 45 out

Spray "simple Green" on engine bay, let soak for a few minutes and rinse.... way easy👍

The knucklehead that put the fuses behind the dash also put the cabin air filter back there. They must have got inspired around Easter when they saw the rabbit look for hidden Easter eggs Lol. I can’t believe it myself and hate every moment I have to fix anything under or in the dash. Have a good one.

Doing this in a salt state truck with 450k miles is quite the interesting time lemme tell ya it was all just one rod fused by rust

Great Idea.

what's the PSI for front airbags. Just finished this project and raised it but front is lower than rear. I have rear at 145psi and front at 140psi. not full lift, but normal height ride.

Thanks battling one now.Now torch though.Wish me luck

you deserve a medal for this video thank youuu🙏🙏🙏

Your the man bro! From the time that I watched your video, went to the store to buy the stuff and had that stupid nut off was no more than 35 minutes, you just saved me hundreds of dollars to have to get a service tech over here. Cheers brother🍻

I need a win too. Timing cover off, diving in to replace oil pump.

Thanks for the video thumb's up

That’s definitely not a 2003.

I cut my 18 mm wrench in half. Works better than anything

wwooow

😊😊😊😊😊😊😊😅😊😊😊😊😊😊😊😊😊

😊😊😊😊😊😊😊😅😊😊😊😊😊😊😊😊😊

😊😊😊😊😊😊😊😅😊😊😊😊😊😊😊😊😊

What happens after you tie wrap it shut and your ac still coming out the vents. I check for vacuum leaks too

Did you change the pump pressure spring out? It’s insane what you have to pull. I’m not going to do mine. Just pump and pressure switch.

had the same nightmare myself 1995 winnebago been throwing coils and ignition modules pplugs wires etc...... tightend up the ignition coil got spark still no fuel distrbutor is last in line. thanks this video almost confirms my theory as of today!!!

im sure that you have now figured out that the leak was not from the radiator in that saab instead it was coming into the cabin from the cabin filter not being sealed at the factory. right?

Hi Travis not heard of you in a while let's see how this one turns out. I still have the LR3 Ans the suspension is still up on what you did . Hope you're ok 👍👍👍 Andy from England

Worked like a charm! Thanks a million!

after how long does the air in the system begin to release?I was thinking of doing that too but I'm not sure about it...

map gas

what if i just leave the zip ties locked and not fix the vacuum lines, i just want cold air out from the front panels, would that be ok, and no need to change anything

What is the part number of the steering line? You think it'll fit on a 01 Windstar?

YOU ARE THE FREAKING MAN!! IT WORKED!!! 2 days iv been heating and prying and jumping on this bitch even tried jacking it up I sat there with a torch for 10 minutes then took a candle just like you said and then took a 5 ft breaker bar and.....BOOM!! BITCH CAME LOOSE!! NOW the bolts on the back of the hub which are exactly next to cv axel boot won't come loose😢 how can I do it without messing up my cv boot? Heating will destroy the boot. Maybe cut the bolts? Next to the splash guard? The new hub assebly should come with new bolts right?

Travis Gill! Thanks man you helped me solve my issue and reminded me after all the OBS in my lifetime to change this Fck ignition module after a while. Now I got her going again and ready for work tomorrow. She’s my daily! 🤙🏽

How long did it take you

Do you know anything about the also infamous engine stalling out when shifting from reverse to drive on these? 2008 cxl with 125,000.

I took out starter and tested with just battery and jumper cables. It moves as it should but when I re-installed I'm not getting any movement to start.

Thank You Sir For The Video..... I had to just do this for my 2007 Grand Marquis.... I used a zip tie. They are Great cars. I wouldn't trade mine of anything.....

thanks so much.

Thank you, sir, that was exactly the problem with my car. God bless you!

10 minutes of map gas and a birthday cake candle. Both done. Thanks so much. If we ever cross paths, I'm buying you a beer!

Thankyou that did help i didnt know about the seal inside .

Couldn’t believe my eyes when it came off but boy did this trick save me a eye twitch😣🤕 lol thank you man you the best

You have a nut?? Germans decided to go with a bolt because we dont deserve to be happy!!!

Love you. Took 45 minutes of heat gun and candle on a 242lb 2014 Honda accord. My impact drill rated at 214lbs.

Expanding and contracting always works. Thanks for sharing!

I just spent 60$ at napa on a socket, 2 cans of pb blaster and inner axle seals and your telling me all i need is a candle?! I swear if this works ill be so pissed and thankful at the same time

What exactly was your truck doing that made you change the whole distributor?

I might be the first person this didn’t work for. Thanks for the tip, it was worth an effort but I think I’m just screwed. 30 minutes of map gas and it won’t budge. Wish me luck, taking it to the mechanic. 😭

Thank you from up here in Columbia!