Video

Seems you can't buy these aluminum rail tracks anymore. Your amazon link is no longer there. Where else can I get one? The Arizona heat destroys the vinyl ones,

What number for bulbs?

thanks friend

I just got a pair of rotors and they sold me only one kit of brake pads. The pad kit has two brake pads, they said it's all I need. According to this video I need four brake pads. I need to do booth front brakes on my 2010 nissan frontier, pro 4x king cab, 4x4.

Zzz zzzzz zzzzz

Thanks. This is helpful.

If you use heat you don’t need 24 hours, I leave mine under a heat lamp for 1 hour for star type plastic and an hour and a half for champ type plastics

"a little error", that is a failed print, my first two prints detached from the bed.

Thanks for the video. It helped a lot! If I want to use remote for the light also how would I wire it?

Thank you for the video . How long does this fix work for ?

this guy is what you dont want to see show up at your house. He has no clue. Never use latex caulk under a problem threshold

How are you liking the Kingroon PLA+?

Is that the printing plate it comes with?

Did you ever figure it out what happened to the poor benchy? Because to me, it looks like a failed print.

Just take the battery and battery basket out. They just pull out and you're looking down on the fan and pulley. Much easier.

After I've. installed the new door seal, when I close the door, I need to put more force. What is the solution? Shall I make small holes here and there in the new seal?

Yes short and to the point

7:38 i just sliced my thumb open because i followed your instructions on how to remove this plastic knob and it wouldn’t work. There’s gotta be a better way

Nothing against Ridgid tools, whatever. I've used and own some of which YOUR action demonstration is a put off and failure if i was to be an inexperienced customer

1:13 pm lock won't open latch. Door is locked closed. How do I open?

I have a 2004 Dodge Caravan SXT all of a sudden one afternoon turned van on shut off, turned on again then it shut off again. Then the blinking red security came on. and would not crank or do anything. Gonna try this overnight. Any suggestions if the hard reset doesnt take?

Hi. I saw your video. Looks great but your video views are not increasing. I'll help you 😊. I'm a CZcams expert

Lol after a few months its all loose again

Supper great video, I'm a woman but i going to give it a try, thanks so much

He hammers with a screwdriver, levers with a screwdriver and botches along the way. Not a trained tradesman. Cannot calk, what a mess.

As always excellent tutorial, just save myself a couple hundred dollars.

Thanks !! Very useful and easy to follow video.

the nut should be nug, not to tight. If it still drips, you can always tighten it a little more. by tightening to tight, you shorten the life of the new seal.

Very clear instructions and easy to do. Thank you. The issue I'm having is that after I did all of this. The line from the inside to the back/bottom is still clogged. I've been putting hot water in the tray on the inside and it just sits there. I've had the fridge unplugged for almost two hours. What ever ice in that line should have melted by now. What do I do?

If ice is sitting at the button, isn't that the leak indicator?

Isn’t it funny how i live right by 15, i mean right behind the tee box lol

High quality sound effects 👌

so the seat cushion that you purchased fits both the BackPack cart + the Trekker cart? I just ordered the Trekker LG cart with the orange Frame + the Black insert bag, and now I'm looking for the seat cushion. How much did you pay for that cushion? Zuca is asking $25.00 for them.

Any idea what to do when the light is flickering randomly and not working most times, and the fan isn’t working at all? This just started a few days ago.

What is your base for the pro chem product you put into the dropper Since the pro chem comes in powder form.

You replaced the left headlight but the right one seems much harder to access.

Caulking instead of SILICONE OR NP1?

Multi tools should take all that old glue off the concrete 😂

Its 60lb feet and 20lb feet of torque for those bolts. You're reading the NM torque as lb feet.

Love it, Thank You !!!

I’m undergoing the whole kit in a few weeks. Thank you. Your saving me hours already

Looked good Love the flight. I will need one

Hello bro, great video, a question, does your filament dry well?

Is this the same steps, for the 2.0 turbo model? Or extra steps.

What is the purpose for the spline? Is that something that would be needed for each replacement?

Rear plugs That's what I need a video about. (Edit) but based on this video, I got-r-done! So thanks!

What was the small part you transferred from the old heating element to the new one? Was that a fuse?

what weight and plastic do you have? I have Alpha 174g. I'm 51 , have 55 mph arm speed and 1000 rpm spin. My Tex thrown flat out the box was straight. Then I threw it hard flat again and it flew like a dome but showed torque resistance. Anny it got to the ground quick. Sadly I wasnt getting the -3 turn out the box. Yours looked like it turned very easily

Already got the parts i need sitting in my Rock Auto cart. Thanks for the straightforward video 👍

This is a helpful video. I was wondering why you aren’t wearing 🧤? I keep thinking you’re gonna cut your fingers. 😮