Everything Mechanical
Everything Mechanical
  • 37
  • 479 321
Installing and testing an in-line clutch pull reducer
In this video, I demonstrate and explain how I installed an in-line clutch pull reducer, as well as test whether or not it reduces the amount of force required to operate the clutch.
I found that this product worked very well at both making the clutch lighter and increasing the clutch's range of engagement.
Part used (many similar can be found searching easy pull clutch lever or similar): www.ebay.com/itm/293973716451?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=zrfusfuoqws&sssrc=2047675&ssuid=QRhxyQxQRLK&widget_ver=artemis&media=COPY
Please feel free to leave any questions or comments in the comment section down below as I am more than happy to answer them!
zhlédnutí: 77

Video

Replacing head gasket and piston rings in 2009 WR250F
zhlédnutí 290Před 7 měsíci
In this video, I demonstrate how I replaced the head gasket and piston rings in my 2009 Yamaha WR250F. Please let me know if you have any questions in the comment section below as I would be happy to answer them!
Installing a block heater in a 2020 Toyota Tacoma
zhlédnutí 3,8KPřed 7 měsíci
In this video, I demonstrate and explain how I installed a block heater in my 3rd Gen (2020) Toyota Tacoma. Part used: Kats 11813 Engine Heater Please feel free to leave any questions or comments in the comment section down below as I would be happy to answer them!
How to protect your vehicle with Fluid-film
zhlédnutí 1,7KPřed 7 měsíci
In this video I demonstrate and explain how I apply Fluid-film to my vehicles If you have any questions feel free to leave them in the comments down below as I would be happy to answer them!
Building a heavy-duty work bench for less than $50!
zhlédnutí 642Před rokem
in this video, I demonstrate and explain how I built my workbench. If you have any questions feel free to leave them in the comment section down below
How to remove paint and grease stains from Carhartt jacket easily
zhlédnutí 8KPřed rokem
Remove almost any Carhartt stain easy with these simple steps: 1. Apply non-acetone nail polish remover to the affected area and let soak. 2. Agitate the affected area with a brush. Repeat steps 1 and 2 as needed. 3. Wash and dry according to care instructions Worked great on my hard- set in paint, grease, and oil stains. Test first to make sure you don't bleach the fabric! Let me know if you h...
How to delete OBS ford smog pump
zhlédnutí 13KPřed rokem
In this video, I demonstrate and explain how I removed and deleted the smog pump in my 1990 F250 with a 7.5L 460 under the hood. Please let me know if you have any questions in the comments down below as I would be more than happy to answer them!
Replacing wheel bearings and CV axles on a Ford Ranger
zhlédnutí 2,1KPřed rokem
In this video, I demonstrate and explain how I was able to replace and install new wheel bearings and CV axles in my 2008 Ford Ranger. If you have any questions, feel free to leave them in the comment section below!
Installing Hipa carburetor, spark plug, air filter, fuel lines, and fuel filter on an Echo SRM 266
zhlédnutí 1,5KPřed 2 lety
In this video I demonstrate and explain how I installed new Hipa parts on an Echo SRM 266 string trimmer. Hipa parts website: www.hipastore.com/ 10% off coupon code: Mechanical I will make sure to post updates on the parts as I contnue to use this trimmer down in the comment section below Feel free to leave any questions or comments down below!
Installing a shelf in my OBS Ford truck
zhlédnutí 1,2KPřed 2 lety
In this video I demonstrate and explain how I installed the VDP Shelf-it system in my truck. Feel free to leave any questions in the comment section down below!
Installing/fixing Badland 2500 winch
zhlédnutí 2,6KPřed 2 lety
In this video I demonstrate and explain how I replaced the winch on my Yamaha Wolverine, as well as how I used the wiring that came with the original winch on the quad. If you have any questions, please leave them in the comment section down below!
Stihl FS56 VS Echo SRM225
zhlédnutí 33KPřed 2 lety
In this video I explain the differences and compare the STIHL FS65 and the ECHO SRM225 I'm sure you can tell that I definitely prefer the Stihl. Both are great trimmers but I don't see why anyone would buy the Echo over the Stihl especially after seeing how well the FS56 holds up over time. When you bump the head on the Echo, the engine really struggles to keep the rpms up enough to cut the lin...
Flipping an old Bobcat mower
zhlédnutí 4,3KPřed 2 lety
In this video I demonstrate how I bought, fixed and sold a Bobcat walk behind mower. I actually sold it for $350, I screwed up in the video
Working on my new SCAG SWZT mower
zhlédnutí 6KPřed 3 lety
In this video I demonstrate and explain how I repaired my new SCAG SWZT 52" mower. If you have any questions, feel free to leave them in the comment section down below as I would be more than happy to answer them!
swapping a Yamaha Warrior carburetor into a Wolverine
zhlédnutí 12KPřed 3 lety
In this video I explain and demonstrate how to install a Yamaha warrior carburetor into a Yamaha wolverine. If you have any questions, feel free to leave them in the comment section down below as I would be more than happy to answer them!
Bleeding the clutch in a 2008 Ford Ranger
zhlédnutí 18KPřed 3 lety
Bleeding the clutch in a 2008 Ford Ranger
Servicing the rear gearbox on a 95-05 Yamaha Wolverine 350
zhlédnutí 12KPřed 3 lety
Servicing the rear gearbox on a 95-05 Yamaha Wolverine 350
How to clean the carburetor on a Yamaha Wolverine 350
zhlédnutí 17KPřed 3 lety
How to clean the carburetor on a Yamaha Wolverine 350
How to: Replace Yamaha Wolverine/ Warrior top end
zhlédnutí 12KPřed 3 lety
How to: Replace Yamaha Wolverine/ Warrior top end
Cleaning the Carburetor on a Toro Snow Blower
zhlédnutí 79KPřed 3 lety
Cleaning the Carburetor on a Toro Snow Blower
Yamaha Warrior 350 carb clean and accelerator pump mod
zhlédnutí 18KPřed 3 lety
Yamaha Warrior 350 carb clean and accelerator pump mod
Replacing Yamaha Warrior 350 battery
zhlédnutí 2,6KPřed 3 lety
Replacing Yamaha Warrior 350 battery
Everything you need to know about fall walk behind mowers
zhlédnutí 27KPřed 3 lety
Everything you need to know about fall walk behind mowers
Everything you need to know about fall cleanup equipment
zhlédnutí 320Před 3 lety
Everything you need to know about fall cleanup equipment
STIHL BR800 & RedMax EBZ8550 review and comparison
zhlédnutí 41KPřed 3 lety
STIHL BR800 & RedMax EBZ8550 review and comparison
How to change wheel bearings in 1995-05 Yamaha Wolverine 350 4x4
zhlédnutí 4,2KPřed 3 lety
How to change wheel bearings in 1995-05 Yamaha Wolverine 350 4x4
How to test & adjust the RPMs of any walk-behind leaf blower
zhlédnutí 3,2KPřed 3 lety
How to test & adjust the RPMs of any walk-behind leaf blower
How to build a sulky for any walk-behind mower
zhlédnutí 22KPřed 3 lety
How to build a sulky for any walk-behind mower
How to add emergency jumper cables to Yamaha Warrior 350
zhlédnutí 1,6KPřed 3 lety
How to add emergency jumper cables to Yamaha Warrior 350
Scag deck adjustment, bearing change and maintenance
zhlédnutí 10KPřed 3 lety
Scag deck adjustment, bearing change and maintenance

Komentáře

  • @ews-texas5258
    @ews-texas5258 Před 2 dny

    Can you get parts for the stihl from Home Depot or lowes?

  • @uf3y
    @uf3y Před 6 dny

    Very helpful, Thank you.

  • @Electricianarchery
    @Electricianarchery Před 6 dny

    Dude I’m about to do this on my 99. She’s alittle Smokey on start up but she compression tested about 128 psi so I’m just going seals and maybe the 366 zoom zoom in the winter.

  • @Evanx373
    @Evanx373 Před 9 dny

    I personally hate speed feed heads. I can load my Husqvarna t35 head in less than a min and it holds almost 30 ft of .105 line.

  • @kevinanderson4610
    @kevinanderson4610 Před 14 dny

    Do you know what the 2 cans are with the red vacuum lines? I’m guessing even with the smog pump removed I still need these??? Please help, I’m desperate.

  • @steveningram865
    @steveningram865 Před 18 dny

    lol no new gardener would spend that amount of money to start of with not very good advice in my opinion

  • @robertthabassist
    @robertthabassist Před 21 dnem

    Is the wiring harness for a warrior the same as a wolverine?

  • @7redash7
    @7redash7 Před 23 dny

    Thank you for the video! But my problem remains. Do you have a link for the zoom zoom-carburetor you are using?

  • @pathallman8641
    @pathallman8641 Před 24 dny

    Stihl is crap

  • @_JamesBrown
    @_JamesBrown Před 25 dny

    Thanks. I just picked up a Gravely Pro 50 walk behind for $450 and almost threw up at the cost to buy a sulky

  • @TaiTran-zc9qp
    @TaiTran-zc9qp Před 26 dny

    yep. you got that right. stihl is the best

  • @partytime11
    @partytime11 Před měsícem

    After finding this video I want to put this comment to see if anyone would know possibly what’s wrong with my quad. I got a 2007 Yamaha raptor 350 I’m in the middle of doing the timing chain and when I drained the oil I had some metal in it but not a lot then I took the oil filter off and had a bunch of metal shavings on the filter and in the oil filter housing. When my quad is hot it doesn’t like it shift into neutral does anything think that the neutral gearing in the engine is bad or could it be something else causing my issue?

    • @everythingmechanical4638
      @everythingmechanical4638 Před měsícem

      A lot of people think they have metal in their oil filter when it’s really just clutch dust from normal wear. Unless you have chunks of metal in the filter or more likely the screen, you’re probably okay. Check to see if the particles are magnetic first. As far as neutral being hard to find, your shift star or spring could in theory be worn out but I’d say it’s unlikely. If your bike has an aftermarket direct mount shifter that can make it harder to find too.

    • @partytime11
      @partytime11 Před měsícem

      @@everythingmechanical4638 I had some pretty small metal chunks in the oil it’s self but nothing huge. I didn’t know if the shift cam assembly would cause something like that or possibly the neutral gear itself is going in wheeler. I just don’t want to run it and have something in the gearing blow or something if it’s potentially only the shift assembly

    • @everythingmechanical4638
      @everythingmechanical4638 Před měsícem

      @@partytime11 I doubt you will, honestly these engines are really tough and the oil pumps are really strong, I’ve seen some pretty big chunks of metal in the bottom of these engines even a tooth off 4th gear and we didn’t know until I tore it apart for a rod knock. I’d check if the chunks are magnetic but again if it looks like a little bit of glitter in the oil filter it’s probably just clutch dust

    • @partytime11
      @partytime11 Před měsícem

      @@everythingmechanical4638 ok good to know thank you for your opinion cause I’ve been worried I got to take the engine out and do a rebuild which is something I don’t want to do

  • @badtothebone346
    @badtothebone346 Před měsícem

    I have both units. The main difference in servicing them is that the carb on the Echo is easier to take off. It takes 2 screws and is off. With the Stihl, you have to take some of the casing off to service the carb. Servicing the spark arrestor is easier on the Stihl. Both units perform about the same.

  • @Ramcat_Vlogs
    @Ramcat_Vlogs Před měsícem

    6:55 I forget how spoiled I am having the 1/2” Milwaukee impact like I have. It’s not everyday I use it but it’s times like this I’m sure glad I’m not dragging out a hose lol

  • @DogDaze66
    @DogDaze66 Před měsícem

    Redmax all day!

  • @user-uf3ms1bp2t
    @user-uf3ms1bp2t Před měsícem

    Where is the tracking adjustment bolt? My SWZT is pulling right.

  • @kevinanderson4610
    @kevinanderson4610 Před měsícem

    What are the 2 little canisters with the red vacuum lines going to them for? I just purchased on of these trucks with this set up. The check engine light is on. I see the connector like yours, but no canisters

  • @RyanDaniel-kd1vg
    @RyanDaniel-kd1vg Před měsícem

    Most of your problems could be solved by using the guard

  • @shmedwinardo
    @shmedwinardo Před měsícem

    This is a great video! Good job! I been wanting to try this cus it’s been getting more and more difficult to get into 1st gear/reverse if I’m completely 100% stopped. 🎉🔧👨🏻‍🔧

  • @gunsandrotors8704
    @gunsandrotors8704 Před měsícem

    Picked up that same Stihl on sale for 199.99 at Ace hardware. For home use cant go wrong.

  • @dwaynebrock1312
    @dwaynebrock1312 Před 2 měsíci

    We ran fs56 for a long time before we got our 91 and 131 and it's unreal the abuse they have been through and they still stay on the truck as backups

  • @user-qz9nd6bi2m
    @user-qz9nd6bi2m Před 2 měsíci

    I like the echo 225 it has plenty of power and I have weedeated lots of yards with it

  • @brucelewis1017
    @brucelewis1017 Před 2 měsíci

    I have a sthil fs 91 and a echo smr 230 and my echo is lighter than the sthil but the sthil has more power

  • @GaryT1952
    @GaryT1952 Před 2 měsíci

    I have basically that same mower although 48" and a bit older...bought new in 1987, never used commercially, always garage stored and still has original belts and tires. One of the most reliable and best built pieces of equipment I have ever owned. Always wondered how that transmission worked...now I know...thank you

  • @helonwhels1206
    @helonwhels1206 Před 2 měsíci

    That tiny little roller is a key for the oil pump, I’m 3 years to late but I’m here

    • @everythingmechanical4638
      @everythingmechanical4638 Před měsícem

      It looks similar but I replaced the oil pump and the old one wasn’t missing it

    • @EvoBeast509
      @EvoBeast509 Před 3 dny

      It wasn't the pin holding the top timing chain gear? I've dropped one into the engine on a yakama timberwolf. Slippery little buggers.

  • @helonwhels1206
    @helonwhels1206 Před 2 měsíci

    10:54 oil pump

  • @rabidfarmer9765
    @rabidfarmer9765 Před 2 měsíci

    Very nice! I buy them as you told me - in the off season. Cheaper than dirt sometimes. ONes w/ lots of issues are almost free. Many thanks!

  • @melonboi186
    @melonboi186 Před 2 měsíci

    you are so biased towards stihl. you only like the comments saying stihl is better or echo sucks.

  • @fergusonto-2032
    @fergusonto-2032 Před 2 měsíci

    I bought a used Scag model: swz48-14kh but the blades won’t engage , seller said he thought it was the switch , how do I check that & how do I determine if it’s clutch ?

  • @user-nb4ps7st9q
    @user-nb4ps7st9q Před 2 měsíci

    Stihl is beter

  • @bairfreedom
    @bairfreedom Před 2 měsíci

    I have a 86 460 Big Block that is in a E350 motor home. The catalytic converter was sawed out before I took it on as a project and I have been replacing parts like water pump etc. I ran into the smog pump and I was like......Do I need this? Looks like that is a no. Which is going to save me ALOT of time and money. Just gonna get me an alternator bracket replacement and get rid of this thing and bridge where the cat convert was. This baby is LOUD when the pipes been cut. Lol

  • @marvadavis1101
    @marvadavis1101 Před 2 měsíci

    Where can I buy a good used Sulky and bush mower for a reasonable price?

  • @garyalensr
    @garyalensr Před 2 měsíci

    I see your obviously a Stihl fan, you've commented and hearted all the comments about the Sthil but ignore all the Echo comments. My opinion is Echo is hands down better than the Stihl. I think the SRM has plenty of power for cutting tasks

    • @everythingmechanical4638
      @everythingmechanical4638 Před 2 měsíci

      The 2320 is a great machine and only slightly higher price. Most of the echo comments are people mad that I like the Stihl better but probably never used much else

    • @everythingmechanical4638
      @everythingmechanical4638 Před 2 měsíci

      But regardless if you watch my blower video you’ll see I’m not partial to Stihl I think the RedMax is better machine in my opinion

  • @JayMoney-tw7tg
    @JayMoney-tw7tg Před 2 měsíci

    I have a question: Can I use the fs56rc for commercial use, or is that questionable

    • @tuberocker69
      @tuberocker69 Před 2 měsíci

      Yes! The only real gripe I've heard is that the gas tank is a little small for commercial use. If you don't mind filling up a couple of extra times there's no doubt it'll do the job!

  • @mikeingalsbee2959
    @mikeingalsbee2959 Před 2 měsíci

    The top bolt on mine did not come out. It bent the bolt and stripped the threads in the pump. I can't get it out now and not sure what to do. Thanks a lot.

  • @NoahVR010
    @NoahVR010 Před 3 měsíci

    That's why I like Stihl better because of their power, efficiency, durability, and their bump feeds are way better then others no offense other companies.

    • @melonboi186
      @melonboi186 Před 2 měsíci

      No, echo's speed feed is better because Stihl still has the old tape it apart system

  • @MikeHensley-sc3ns
    @MikeHensley-sc3ns Před 3 měsíci

    About to buy the echo!

  • @WhiteYetiAK
    @WhiteYetiAK Před 3 měsíci

    All the ones I found online are out of stock. I really wish they were available, because I have 5 trucks I could mount them in.

  • @treythe3-dprintinggeek
    @treythe3-dprintinggeek Před 3 měsíci

    rebuilding my 350 and that broken peice looks like the cam end where the sproket goes on same with that little pin

  • @jameslaiola4976
    @jameslaiola4976 Před 3 měsíci

    Thank you so much Sir. Sadly mine is squealing hysterically as well. Im Definitly considering this now. I would love to respectfully ask if you also know the belt to use to bypass the A/C ?

  • @donaldbunce5410
    @donaldbunce5410 Před 3 měsíci

    You didn't show how to get the old throttle cable into the new one

  • @jr233-x6r
    @jr233-x6r Před 3 měsíci

    toro does make a zero turn walk behind i was looking at and getting rid of my scag belt drive 48

  • @djturnz
    @djturnz Před 3 měsíci

    A buddy use used to have one in his lifted truck, which was OK. I grabbed one on marketplace a while back. I was planning to try mounting it in my car, but I'm 6'4", so I need to make sure it's not too low. I just haven't been ambitious enough yet.

  • @stephenkowalski2448
    @stephenkowalski2448 Před 3 měsíci

    Just the video i was looking for, i was looking at buying the echo but they now selling the stihl at $199. I have the FS90 for over 10 years but i'm looking for a string only trimmer. Too much trouble to switch from blade to string and the FS90 is a tank for grass trimming. Considering the stihl is lighter i think ill go stihl as im looking fir a lightweight grass trimmer. At only $200 and lighter weight its not worty the time swapping from blade to string on my FS90

  • @Stuckin330
    @Stuckin330 Před 3 měsíci

    That’s not how u fix the excel pump mod you need to use a small rubber hose that slide in tight on the pump plunger so it advanced an start pushing plunger as soon as you hit the throttle

  • @richcityrepresentative8805
    @richcityrepresentative8805 Před 3 měsíci

    Once you break the motor in and adjust the carb, the 225 will cut thick grass/weeds no problem.. i love my 225!!!

  • @RonnieMoscaAmericanstangs6033

    I have and prefer echo equipment. Just my preference, Their products never let me down and are easy to work on .

  • @johnfenwick4095
    @johnfenwick4095 Před 3 měsíci

    Really really like the video thank you anything more on the 1990 F-250 460 I greatly appreciated had the truck over 10 years I think I blew a head gasket foaming out of the radiator foaming so I guess I'll be doing the head gasket soon thanks

  • @Noahthelandscaper
    @Noahthelandscaper Před 4 měsíci

    I had an Echo SRM 225 but then I sold it to mad dad and then I bought a 420 dollar Stihl FS 94R

  • @Evadingmoto
    @Evadingmoto Před 4 měsíci

    How tight was the spring. Mine isn’t budging