Video

Make a video on heat load calculation

Is there a way to lock the thermostat apart from altering the temp up or down? We have in a holiday let, but have trouble with guests accessing areas of setting by accident. Tia

Hello, could you please share with me your email address as I have home and need to get the materials

Padlock symbol appeared on mine. How do I get access to?

Awesome video cheers mate

Can someone help me to get the lock key off while the thermostat is off please

No benefit of putting screed on top or unnecessary?

Is there a way to reduce the brightness or have the screen off at night (while it is still working) as it is very bright and causes a disturbance while we try sleep. We have already put the general brightness to 10% (the lowest setting) but this isn’t enough as when all lights are off it’s quite bright all night.

I have one of my pro touch WiFi thermostat locked how can I unlock it?

0:16 - How to Factory reset 0:56 - Room temperature calibration - If room temperature is showing an untrue value, same procedure for floor temperature 1:44 2:10 - Frost protection mode 3:31 - Setting Floor temperature limit - to protect floors such as vinyl & wood 4:39 - Reverse output - If your heating isn't coming on when it should it could be reverse output. 5:40 - How to remove E2 Error Code 6:54 - Adaptive function - If your heating is coming on when it shouldn't it could be adaptive function

0:14 How to power on/off 0:35 How to set date and time 1:35 How to programme on/off times and temperatures 4:50 How to manually adjust the temperature 6:56 How to change between air and floor temperature - ALSO removes E2 error code. 8:39 How to set holiday mode

Dose this has WiFi compatibility? ProWarm™ ProTouch-2 Touchscreen Thermostat

I’ve just put 10mm of levelling compound down supplied by pro warm. How long do I leave to dry before I can turn heating on?

Glad you made these at last. Helps a lot

Does it work on 5Ghz if thats the only freq of the router ? 1:24

Hi Could you please tell me what size notches trowel you are using just before laying the insulation boards at 5:00 timeline in this video. Thanks

Please can you tell me if I can lay 8mm Quickstep laminate flooring straight onto this heating mat? How thick is this heating mat? Thank you in advance.

Dose this compatible with prowarm underfloor heating mat kit 200W 4.5 m square. ?

Excellent video 👍

Great video 👌 Everything demonstrated and explained well.

Can you do a separate video for the time clock option please ?

how do you set a different temperature time for different days such as later on time at the weekends

Would be grateful for a guide on the Prowarm Wifi v2 install and setup guide (or both as separate videos please

Are you leaving the lcd thermostat that low down on the ground ?

This is just crap music, not an instruction video. A waste of time

Hi, just installed the manifold & would now like to fill it… What fitting do I need to get so I can connect the hose pipe….? Thanks 🙏🏻

I installed exactly the same like in the video but i cut the tire and it’s been 3 days and no heat can someone give me an advice please

Can I build this installation in only 13cm hight?

What is the thickness of the system before installing the wooden floor or tiles? Thank you!

I've just moved to a bungalow with 2 of these things. Why have they put 2 in? They are either side of the door. The previous owner only installed the boiler 4 months before I moved in. To use this do I have have to have the boiler alway on? Or can I use the time? Anyone any ideas?

Nice renders bro

Dear Expert, Thank you for the brilliant explanation. My question is whether we can install new laminate on top of old ceramics while using a wet floor heating system. Could you please guide me on whether this would prevent efficient heating conductivity, increase energy consumption, and how it might affect moisture levels? Additionally, what steps can I take to control these factors? Best regards,

can i use it in the kitchen?

Super

يا فشل

Don't understand why it is necessary to fix boards down with adhesive on a concrete or for that matter any surface base?

What mode and speed for underfloor heating?

Very risky to just loose lay these boards as subfloors are rarely 100% flat even with levelling compound and any voids could cause deflection in the board. Its wise to stick with tile adhesive and also screw with screws and washers. Also bare in mind that it was mentioned they are a gypsum product, if this is correct it's vital to prime the boards properly before using a cement based adhesive or leveller, as gypsum and cement together cause a reaction that will compromise the bond. I hope that helps and good luck!

Mine has never worked

So you charge 4 less also then

Yes but what do the settings mean and what setting should be used for a typical house heating system?

Great video, thanks

just missing the info about the heat loss through that thin board, perhaps add that the min insulation beneath should be 150mm of λ=0.2 W/(mK), add that the floor heating needs a thermal mass and cannot be less than 40mm but preferably 80-100mm - not 5mm ! to actually run properly, add that the floor heating runs continuously and will not work efficiently in the property without the buffer tank where a combi runs on demand, add that the floor heating should never exceed 24degC as we use radiant heat only , we don't want convection nor swollen feet. add that a floor heating doesn't work properly when covered with wood, it needs ceramic/porcelain tiles to perform at its max. perhaps learn from countries which use floor heating for the past 30 years as you have zero experience in this.

how long does it take to install it?Best case scenario,Normal and worst?

helpful video！🤓may i ask whether it is waterproof layer or just glue coating from 1:55 ？cuz i see you add yellow layer after that？also what's the yellow one？ thank you！

3:00 yeah and 50% of wooden joists with ambient temperatures... british... not so "great" way of building... your way of underfloor "heating" works when heating is on, and it doesnt when heating is off- there is no buffer in 1mm thck or less aluminium plate and the heat is not stored at all. also wooden flooring acts as an insulator forcing users to increase the heating temperature to achieve max 24degC output to avoid swollen feet. do it right ground floor - remove timber, insulate with styroconcrete or leca , or do a proper slab then 150mm of polystyrene and anhydrate pour. insulate foundations all the way to the ground because in your sht example 22mm plank is the only thing that separates you from the cold under the floor especially by the walls

I am not a plumber but would like to know at what flow speed the pump is set at...in the video clip it only shows how to change the flow but does not explain which each setting means...how many lights for fast flow and how many for slow..confused...

how will I know at what speed my pump is running. Thanks

What kind of Cement it will use to stick between wikis floor and shower tray thanks

Floor heating requires 150mm of Lambda=0.036 graphite polystyrene to ensure there is no loss. You can only waste your money and time with 10mm xps.