- 20
- 15 029
The Source, Robert Hays
Registrace 2. 02. 2011
June 30, 2024. How to put a generator pulley on an air cooled Volkswagen properly
How to put a generator pulley on an air cooled Volkswagen properly
zhlédnutí: 53
Video
A Real Nice 1965 Brazilian VW Bus
zhlédnutí 69Před 3 měsíci
Pretty much nothing mechanical works. What I say about the rear brakes is a fact. Check the play at the lever with adjusters backed off. Be sure the shoes are fully engaged in adjusters and wheel cylinder pistons with pistons pressed in all the way (You'll need to do this and the following each time you check with th springs installed). The speader bar can prevent this because the slots on the ...
My Type 4 Volkswagen Engine Oil Light Goes on While Braking and Around Turns
zhlédnutí 81Před 3 měsíci
This works. Fixing it with an assembled engine is hard but possible. Changing the tube during assembly is easy. Change the tube! Forgot to mention you'll need to drill a hole in the channel for draining. The pickup tube can be withdrawn and reinserted from the bore (not from the engine) with engine assmbled. Withdraw the tube to enable access with a 1/8 drill bit. Place hole near bottom of chan...
Fix up 1974 Porsche 911 S front brakes calipers for those of you interested in details.
zhlédnutí 36Před 4 měsíci
Determine if your pitted brake caliper pistons will cause fluid leakeage or not.
March 27, 2024 How to bleed the brakes by yourself all alone on anything
zhlédnutí 9Před 5 měsíci
Don't watch if you don't want to know how to free up really frozen brake caliper pistons on a 1974 Porsche 911 and many other vehicles.
How to REALLY replace the long shift rod bushings in an air cooled VW and much more
zhlédnutí 40Před 11 měsíci
How to REALLY replace the long shift rod bushings in an air cooled VW and much more
How to really do a grease job on a 1967 VW Westphalia camper bus
zhlédnutí 11Před 11 měsíci
How to really do a grease job on a 1967 VW Westphalia camper bus
Replacing the shift rod bushing in an air cooled Volkswagen Bug the right way.
zhlédnutí 1,5KPřed rokem
This is how you do it so it'll really last and have a less throw than it had when the car brand new. Somehow the video is flipped so left is right and right is left. PS - I'm not a member of the "You just go like this and it'll be cool" club. Details matter. They make things viable - ready for a trip to Saturn and beyond. I'm not here to set speed records for engine assembly and such. The only ...
Home Depot parking lot dwelling van needs a little work. Get paid to take it away.
zhlédnutí 13Před rokem
Home Depot parking lot dwelling van needs a little work. Get paid to take it away.
Preparing the VW flywheel and flywheel area for final flywheel installation.
zhlédnutí 33Před rokem
It's the little things that aren't in the book and there's a lot of them.
Leaky VW intake manifold/weak valve springs? Can an intake port leak?
zhlédnutí 63Před rokem
Leaky VW intake manifold/weak valve springs? Can an intake port leak?
Gutless rebuilt air cooled Volkswagen engine diagnosed and fixed, Part One.
zhlédnutí 186Před rokem
Gutless rebuilt air cooled Volkswagen engine diagnosed and fixed, Part One.
Brake job on an air cooled Volkswagen bug. Part One - wheel cylinders.
zhlédnutí 13Před rokem
Brake job on an air cooled Volkswagen bug. Part One - wheel cylinders.
Find cylinder head surface area to determine combustion chamber surface area in air cooled VW
zhlédnutí 197Před rokem
Find cylinder head surface area to determine combustion chamber surface area in air cooled VW
Incidentally, the o ring for the cover (end cap) Stoddard part number is SIC 351 999 00 or 901 351 999 00. It doesn't come with the kit.
I hate seeing people do this use smoke or water. 🤠🤔🖖🤫🏴☠️
And booom 🔥 don’t recommend doing this
There's a water hose that's on with a trigger on the hose. And the plug wires aren't junk and the spark plug is in the cylinder head. So no risk.
Engine should speed up not die
It can do either.
You can check for vacuum leaks either way…. With NON-FLAMMABLE the idle drops With FLAMMABLE the idle increases Easy Peasy
Shouldn’t you be using ether or starting fluid for that? Won’t the brakekleen harm seals or gaskets? Asking seriously Ive never seen this done with brake cleaner
It's flammable so wotks. Even WD40 will work. They make a tool specifically for this that uses propane. I have a ttrigger nozzle on a water hose on the floor because a bad spark plug wire can ignite this. I think intake gasket replacement is more of a maintenance thing that something replaced only when leaking or rebuilding the engine.Air leaks burn valves.
Hey buddy! How are you? Just shared my new crime documentary video that took 14 hours of hard work. Your thoughts mean a lot to me, so feel free to share your opinions. Can't wait to hear from you, stay healthy!
Here's my latest content. This time, we're delving into a real crime documentary. Don't hesitate to share your thoughts; I'm eagerly waiting!
Promo`SM 🙏
Also you didn't show welding the bracket back in and what to do about getting the heat off the bracket and not melting the new bushing, i use a water spray bottle after welding each spot weld to stop the heat, also have a wet rag under the rod and around the rod so no slag sticks to the rod. Grat video.
You dont need to weld it on. You use one bolt to hold it up before attempting to install the shifter. The shifter is then installed with one bolt loosely then you can take the other bolt out and use it for the second bolt for the shifter. It's a little tricky but not too bad. By not welding you'll have more adjustment because the retainer isn't stationary. The one I did prior to the one in this video had so little left to right movement in neutral it would favor either 1/2 or 3/4. Adjustment wouldn't do it. I had to put a washer between the lockout plate and the tunnel (or maybe between the lockout plate and the base - can't remember) for each bolt and it was perfect. Adding the washers changed the fulcrum point .
You are correct, replacing the bracket and bushing is best because I've seen the original bracket worn and it makes sharp edges on the bracket and it cuts through the new replacement bushing. I've seen them broken so it has to be replaced. More people need to see your video, I've been looking for someone that addressed this issue, THANKS!
nope
That's one out of round tire... definitely road hop.
It made a dull slapping noise. Was concerned it was a loose wheel for a bit.
We’re gonna get you one day traitor