Video

Thank you for wasting people's valuable time

Thanks. Worked!

I'm about to buy this, but what's not clear is how to get the garage light to switch on or off with these remotes. On the remotes that come with the opener, the big button is for the door. One of the 2 small buttons is for the lights on/off. The 3rd button does nothing. But on these remotes, in this video, when you program the door (A or B) is one of the bottom buttons automatically programmed for the lights?? Thanks in advance for any confirmation/info.

Lavadora portátil

123468? I think you should refresh your english numbers. How did it work when you didnt press the correct amount?

কত

Merci boucon

Your door opener came with instructions which are incoherent and inaccurate. This is true of this video as well.

Cit costa?

কত আমি নিবো

This video saved me! I couldn't figure it out before this. Thank you!

ভাইয়া কত এই দাম

Fgfkta myxa

Хуйня ..стринги стирать ...не более

எங்க கி ட க்கீ ட கும்

Grazie por el vídeo 🥲 no sabía para que servía jaja hasta ahora

What is the price is it used by electricity

🎉колко струва 1бр

❤ top du top

In my case, when the remote control found the code, the learning mode LED on the garage opener is blinking very fast but it does not open the garage door. what is my problem?

Cost

Where did you get this limit switch?

দাম কত

Does not work

I can use default pin 1111# to open and close garage door , but cannot change default pin with included instructions. Please explain how to change default pin. Thanks

НЕ УБИРАЕТСЯ ИЗ МАШИНКИ ОТЖИМНЫЙ БАРАБАН

Hola como se arma la centrifugadora?😢

No se como se arma la centrifugadora 😢

Price

Price pk

¿Tendrá un vídeo de cómo es que se abre el panel de control?

Somehow this worked on my ancient Genie Model 404 "Green Monster". There are no DIP switches in the garage door opener but there is a strip of nine in the original handheld remote. They were set at what is decribed here as "222228882#". I followed the programming instructions here... *# 1# 12# or 16# 222228882#. At that point my old code worked... Not 1111# or 2222# but the code that was working with the wireless Clicker keypad I replaced. Don't ask me how! * Re 12# or 16# above. I can't remember which one worked. They're both for an old Genie.

You are awesome. Most helpful video 👍

Hola, Cada vez que se corta la energia electrica el modulo se desprograma, como puedo solucionarlo?

This worked perfectly for me on the very 1st try!! Thank you so much. Simple and easy to follow. I lost the original instructions and this is actually the only thing that works. Thank you again!

Seller EZ control

I programmed the remote and it worked fine but when I returned home it wouldn’t open the garage door. I tried to reprogram and the remote’s LED light wouldn’t come on to allow the reprogram. I programmed the other remote and it did the same thing. I’m stuck.

I have spent 2 hours trying to figure out how to use this remote. I bought 3 of them non work at all. I ended up throwing them away and trying a another brand that took 15 seconds to program and you don't have to take everything apart.

when i performed these steps it ONLY opens the door; doesn't close it. Am I doing something wrong? It should close AND open the door. Please advise.

Thank you for the TV reference. It cleared up with a were trying to tell me.

Thank you! Reprogrammed successfully!

Thanks. The instruction booklet was so unclear, but thanks to this video I was successful in programming mine after a couple of attempts

If i have two JD-06; one installed on the garage door (outside of the house) and second one installed inside house. When the JD-06 garage door is turn on, do is it trigger o turn on the second JD-06 via RF Anttena?

Helpful. You can also press buttons 2 & 3 simulatenously to begin programming, instead of unscrewing the device to hit the program button.

Very helpful

Finally, a vendor that shows how to program it. Thanks Vicky!

Thank you very much your video saved me alot of headaches! Very clear

Good directions

现在发现在没有任何操作,遥控器放在桌上,车库门会自己打开,尤如按了遥控器

RC-SM24-MX这个遥控在学习配对时没成功,结果现在按三个钮任何一个都是同时关开两个门,怎样重置恢复初始状态, 电路板上有RST NCC GND 等孔怎么用, 请指教, 谢谢