Video

I really like those type of video ! Race prep ! It is my favorite part for me anyway ! Keep up the good work love the xfwd or sfwd content !!! ❤

💪💪💪

Sucks to see, check that turbine wheel too with the aluminum that went through it

You can save that head Dre. Dont toss it. L.A.D.D porting service in Elkridge, MD could fix that.

When the head lifts or gasket fails, oxygen enters the combustion chamber and it gives a torch effect. Doesnt matter if there is water or not. The key word on an oxy-acetyline torch, for example, is the Oxygen it uses to make a stronger flame. Same instance here. When the oxygen is introduced into the combustion events, the torch marks will travel to where the leak presents itself. I've found on the higher HP stuff, to use a copper gasket and fire rings. They've been holding up at 1500+HP on a few K-series I build for drag guys. I have an idea on how to make them work on a B-series too. They are even re-usable LOL

Is that from the combustion pressure and temp basically made a hot spot and blew through it or what ?

How does that happen 😮

dang bro?? wth could've done this other than just pressure? hmmm🧐

😳F

Never Give up! Keep the movement going forward. Can’t wait to see you come back. Best of luck on this journey….

Good content brother! Race break fix repeat

you remind me of brent from pfi so chill and positive even when its not going your way

Very nice job bro 💪 💯 👍

I’m sure you got the office people, managers, and higher ups thinking that they be paying you to much seeing that you have a f350 dually with wheels and a big inclosed trailer.

This Brandon Dre, keep the videos coming brother.

If this sport was easy everybody would be doing it 🤷🏻‍♂️. Hang in there!!

One thing after another! Keep your head up! Keep dropping content, enjoy watching your videos.

damn that clutch and flywheel have seen ALOT of heat

BACK TO THE LAB!! GODSPEED BRO.

the car looks good, Team work makes the Dream work. Good luck in the future for him and the car

Excited to see the future for that car 🚀

Blessed to have you back. Never give up

add more pipe tape to that top one.

And that little boy is my brother

I am your daughter ❤

Yea sir.... like you never got out.... see you somewhere this year.

Glade to have you back racing the beast. 🤜Bless you in this new year🙏

so bad ass! i got #7 out of 50, which number is yours?

Did you need a tune afterwards?

When kicking a 2-stroke dont apply throttle, tilt the bike for a little bit so the carb almost floods and then after a few kicks with choke on try it without a choke. Then repeat until it fires up :) If you take a spill and the bike sits on its side for a few seconds and the engine is hot it might need a full throttle kick if its flooded. This works on a KX250 like a charm 💪

Sounds good!

How’d you like the SBD pads?

How difficult was it to squeeze the filters in?

Nice setup definitely got my sub 💯 my goal is to make it to this level

Good to hear your back and the car sounds amazing

Glade to have you Back Fam!!! Looks sick and ready

Looking good bro

Amico lascia stare questa moto va tutta sistemata

🔥🔥

❤❤❤❤❤❤❤❤❤❤❤❤❤

Lmao I don’t know it was that simple def gunna do it now

Whats the first import race on the calendar over there?

Good hits out there scooter ,worm

It’s still just a gay Honda civic.

Dam that civic is fast

I still take the R35 over that Stang

KEep the content coming bro

Lol .... Gotta help that man I think we have some content to share on him not knowing how to drive a SxS either lol

😂❤كثابكا