- 58
- 64 446
Autodidact Submitted to God
Italy
Registrace 14. 11. 2022
230v 50Hz AC motor with brushless permanent magnet rotor
230v 50Hz AC motor with brushless permanent magnet rotor
zhlédnutí: 26
Video
Dewalt charger DCB115 repair, capacitor and fuse
zhlédnutí 412Před měsícem
Dewalt charger DCB115 repair, capacitor and fuse
Bosch AL 1860 CV charger repair, shorted diodes
zhlédnutí 586Před 2 měsíci
Bosch AL 1860 CV charger repair, shorted diodes
Dewalt DCB115 charger repair, loose connector pins and R values.
zhlédnutí 154Před 2 měsíci
Dewalt DCB115 charger repair, loose connector pins and R values.
Hilti charger C 4/36-ACS repair and R values
zhlédnutí 1,6KPřed 2 měsíci
Hilti charger C 4/36-ACS repair and R values
Makita charger DC18RC T repair of stand by circuit, mosfet, resistors, zener
zhlédnutí 1,4KPřed 2 měsíci
Makita charger DC18RC T repair of stand by circuit, mosfet, resistors, zener
Hilti rotating laser PR 30-HVS repair, doesn't turn on.
zhlédnutí 815Před 3 měsíci
Hilti rotating laser PR 30-HVS repair, doesn't turn on.
Bosch charger GAL 1880 CV resistor values
zhlédnutí 274Před 3 měsíci
Bosch charger GAL 1880 CV resistor values
Bosch charger AL 3640 CV repair, startup resistor problem.
zhlédnutí 351Před 3 měsíci
Bosch charger AL 3640 CV repair, startup resistor problem.
Bosch GLL 3-80 C laser level calibration.
zhlédnutí 2,6KPřed 3 měsíci
Bosch GLL 3-80 C laser level calibration.
Hilti charger C 4/36-350 repair, common problem with standby IC
zhlédnutí 1,4KPřed 3 měsíci
Hilti charger C 4/36-350 repair, common problem with standby IC
Hilti rotating laser PR 2-HS repair, Part 2.
zhlédnutí 145Před 3 měsíci
Hilti rotating laser PR 2-HS repair, Part 2.
Hilti rotating laser PR 2-HS repair, Part 1.
zhlédnutí 380Před 3 měsíci
Hilti rotating laser PR 2-HS repair, Part 1.
Jammed due to dirt, Dewalt recip saw DCS369
zhlédnutí 75Před 4 měsíci
Jammed due to dirt, Dewalt recip saw DCS369
Repairing Milwaukee charger C 12 C, easy fix
zhlédnutí 131Před 4 měsíci
Repairing Milwaukee charger C 12 C, easy fix
Repairing Bosch charger AL 1820 CV, and resistor values
zhlédnutí 1,8KPřed 4 měsíci
Repairing Bosch charger AL 1820 CV, and resistor values
Repairing Dewalt 3D green laser level.
zhlédnutí 660Před 4 měsíci
Repairing Dewalt 3D green laser level.
Repairing and converting Craftsman charger from 120v to 230v or universal
zhlédnutí 367Před 5 měsíci
Repairing and converting Craftsman charger from 120v to 230v or universal
Repairing Makita charger DC18SD, and all measurements.
zhlédnutí 848Před 5 měsíci
Repairing Makita charger DC18SD, and all measurements.
Repairing dual port Makita charger DC18RD, MIP2K2 faulty IC
zhlédnutí 125Před 5 měsíci
Repairing dual port Makita charger DC18RD, MIP2K2 faulty IC
Repairing Parkside screwdriver battery slot
zhlédnutí 68Před 5 měsíci
Repairing Parkside screwdriver battery slot
Repairing Hilti Charger, c4/36-350, MIP2M2 faulty IC
zhlédnutí 1,9KPřed 5 měsíci
Repairing Hilti Charger, c4/36-350, MIP2M2 faulty IC
How to test rotor and stator (armature and field) with a multimeter and visual inspection.
zhlédnutí 1,1KPřed 5 měsíci
How to test rotor and stator (armature and field) with a multimeter and visual inspection.
How to test the mosfets of a BLDC motor driver electronics ESC
zhlédnutí 46Před 5 měsíci
How to test the mosfets of a BLDC motor driver electronics ESC
Replacing the chuck of Makita screwdriver
zhlédnutí 344Před 5 měsíci
Replacing the chuck of Makita screwdriver
Dewalt charger DCB1104, 120v to 230v (or universal) conversion, resistor values, and voltages
zhlédnutí 1,2KPřed 5 měsíci
Dewalt charger DCB1104, 120v to 230v (or universal) conversion, resistor values, and voltages
Dewalt charger DCB107 resistor values and voltages in electrolytic capacitors.
zhlédnutí 496Před 5 měsíci
Dewalt charger DCB107 resistor values and voltages in electrolytic capacitors.
Converting Dewalt charger DCB107 from 120 to 230 or universal.
zhlédnutí 1KPřed 5 měsíci
Converting Dewalt charger DCB107 from 120 to 230 or universal.
Great video! Thanks! On mine, the MOSFET in the corner of the card has blown, I can't read the reference. Can you tell me? And also the reference of the 4 diodes? Thanking you in advance.
Onde encontrar o esquema eletrônico da placa Al 1860 do carregador de bateria Bosch
Sa nakapanood neto nice tutorial
Hilti tools are trickier than most to work on, especially the electronics. Thanks for taking the time to post these!
Thanks for your content I really appreciate your videos as I’m always working on equipment. Can you give me an email address that I can’t contact you about a Hilti DD250 I’m having problems with? Thanks again
what is the problem with DD250?
I have a new model DCB-107.The motherboard number is pcb4445-rev 0.6 2020-04-01.If you can convert it from 110 to 220V, maybe you can record a video
just change the big capacitor to 400-450volts and with half uF value, and remove any varistor that is in parallel before the bridge rectifier
Hello, if the transistor doesn't work, just by changing it would it be fine?
You also have to check nearby resistors and diodes, because when a transistor gets shorted in gate pin, it may damage components or even the IC,
Does this works on te 70 atc?
@@MihaiAlexandruPreda no, it works just for TE76 old model
@@apsubmittedtoGod thank you.
Hello brother i m from pakistan I want to discuss something with you can i get Your WhatsApp contact ❤
Can you convert makita DC18RC 120v to 230v.?
czcams.com/video/vWcRAZqbukw/video.html Replace the capacitor from 220v to 400-450v, and remove the varistor, the yellow component
Very good video, helped to me alot. Thank you
wat is de waarde van de weerstand what is the value of the resistor
180k ohm
Hocam verdiğiniz bilgiler sayesinde tamir başarılı oldu. RS direnci yüksek ohm degeri veriyordu renk koduna ğöre 0.22ohm olması gerekiyordu ve iki paralel direnç olduğu için 0.11ohm olduğu kararına vardım ama bu dirençten yoktu fakat bir tane 0.10ohm 2w direnç vardı onu taktım ve çalıştı yani bu tamir sakıncalımı.değilmi sorum bu teşekkürler hocam 👍👍👍👍
0.11ohm vs 0.1ohm is not a big difference, it will be fine
@@apsubmittedtoGod multimetreile çıkış voltajını takip etim batarya dolduktan sonra 8.55v beklemeye alıyor yani akım algılamada sorun yok.abone oldum
Which God and which holy book?
@@HardcoreHokage-cw4uq the Creator and Owner of everything, the Book of good moral values. God bless you.
@@apsubmittedtoGod ah your talking about Zeus. Where can I get a copy of Zeus' holy book?
@@HardcoreHokage-cw4uq zeus was the son of cronus, he wasnt the creator of the universe
@@apsubmittedtoGod No it was Uranus who created the Universe. Zeus bless you.
@@HardcoreHokage-cw4uq uranus still had parents, so not the God the Creator and Owner of everything
Did you place any additional resistors on the side of the capacitor? Since I see that other boards of the DCB1104 model do not have those resistors.
Exactly the D3 and R7
@@uncanalmas5824 no, i didn't, D3, R7 and the capacitor there are snubber circuit to block voltage spikes coming from transformer, 1:43
Hello. Sorry. I have the same charger. The IC 3113 is ok but does not appear 5 volts. Also oscilator circuit IC P1216 was replaced but the charger does not work. I think first I should have stand by en then the main voltaje but I do not find the problem. Thanks for your answer.
do the LEDs turn on when you plug it in?
@@apsubmittedtoGod no. Nothing happend. Only appear 165 VDC in the mains capacitors.
@@carlosreyes-ko9im so the problem is in the snubber circuit, is it the same exact charger as this in the video?
@@apsubmittedtoGod HI thanks for answer. Modelo charger is DC18RA
@@carlosreyes-ko9im did you find any faulty component there?
Твое видео помогло бы если я не нашел номиналы компонентов ранее вдругом месте ,хорошее дело делаешь. Слава Спасителю Иисусу
Thank you for your valuable contribution, how long has the charger been working for you?
these chargers after conversion work fine, no problems with that
Amen
Hola puedo hacer lo mismo con un TE 70 q tiene la misma alarma y no enciende??
no, it works only with this tool TE76P ATC
Hello, mine is blinking red/green but not charging batteries. what could that be? I have 2 with that problem, a DC18RC and a DC18SD. Regards
are you sure the batteries are ok?, if yes, then check the mosfet, the big capacitor, and small capacitor near the driving IC
@@apsubmittedtoGod Ok. Thx. Picture of the driving IC? Regards
@@user-2uf2kr2c 13:13 IC1 the one with 8 pins, and capacitor C12
@@apsubmittedtoGod Ok thx. Godbless
Hello. Mine stand by voltaje. K3113 is ok, but dont have 5 volts. Do you know what cold be?
How to reset a Hilti TE 3000 avr ??
you need SRT service reset tool, to do that
Sir thank you for your research on hilti chargers. I have a charger and when i try to charge the battery, it start charges for 2 seconds and then turns off the fan and does not charge. It stops after 2 seconds. What could be the cause?
this is a common issue if the battery is faulty, not the charger
@@apsubmittedtoGod thank you so much for replying. This shows your dedication to your subscribers..
That's cool
To change calibrration settings u need to srew or unscrew this small philips screw? NOT the golde one?
not the golden ones, just the small torx screw that is accessible by just removing the protecting glass
مدبيك أقرب فرس رني مسحاقه مزاف من فضلك
نعود الكتيب اخي رني حب تكرولي هلتي باش نخدم بيه
سمحلي مقدرش نكتب
نكري
نظريه عليكم
اخي سلام انا حب هلتي ايل تقدر نظيره عليكم باش نخدم بيه
Nothing important
I have one just like that one bur no lights power going in but nothing out
check stand by circuit, where is the little transformer, check the transistor if it is shorted, or first measure if there is output voltage from that circuit in the capacitor 9:29
Commentary, waste of time.
Good 👍
Thanks
Vous êtes d'où ?
Ic
Out put voltage not stable
So you just changed the capacitor. What about the temperature? Did the charger's temperature rise?"
no, the charger is designed to be universal with the rest of components, just the main capacitor is different, and sometimes they also put a varistor in parallel for overvoltage protection, that can just be removed without a replace
@@apsubmittedtoGod thank you
Best quality HILTI❤
Can you put subtitles
for the moment i don't have time for video editing, maybe in the future i will
Thanks. This is exactly was happened to my battery
😂😂😂😂😂😂😂😂😂
Ти еликтроника ли поправяш или си монтиор
монтьор
Have you also tried charging a 60V battery?
Not with this one, but there isn't any reason it wouldn't charge it
My god is better than your god, and my book says so, so there. Pretty silly sounding, yeah? So is fiction that keeps you in check with fear and guilt.
hello! i don't think the highest capacitance cap i put there would be a problem, it is working fine
Thanks very much for this. You re. Champion!!!
Hola tengo un cargador de esos. Y enciende el led. Y cuando le coloco la bateria . Prende el abanico y se apaga de una vez. Que tu crees que pueda ser..te agradecería tu ayuda
please I need the value of big capacitor
Hi, value of big capacitor? thanks
82uF, 400v