Video

Isn't this a $15,000 fine?

Thanks for the video. Informative... will be doing the job soon.

What do you think is an appropriate price to pay for an engine swap, labor+parts

Such a stupid design

man this is shit. hoses are a fuck job imho.....

Do you guys think that any of these brake Calipers would fit in a 2010 nissan titan without any wheel mod?

Feel like I might have the same issue but my engine isnt over heating or throwing up any codes but definitely sounds like the radiator is over working its self, I rev the car and I just continues to get louder. Do you have any idea on what it could possibly be? everything seems to be fine but the radiator just gets way to loud or something in that area

What else could it be if the sensor has been replaced and no oil pressure until you idle and drive the vehicle ?

Thanks bro running alot better now, no more rough idle

Hey would you know if the DRIVE SHAFT for the Fx35 is the same as that for the Qx37? I have a 2009 fx35 with a VQ35HR engine?

Great job, thank you

I have a small leak on the one that goes to the water pump. It looks like it has like a plastic clamp thing.

Hey how much you want for it? I’m looking for a decent reliable G

Bouta save me hundreds bro. I hope to Gee Oh Dee you got a video on fuel pumps for gmc sierras

Please keep creating Nissan/Infiniti content! You are very honest and mechanic savvy which is very educational to some of us who are owners of these cars.

Thank you for watching! All things considered, the paint came out miles better than what I was expecting

No way it was this easy 😅 im gonna have to do this

any link to the lower and upper fastener i called the dealership and they didnt really understand what i was talking about

Did you get a check engine light after installing it ?

If you have a good air hammer, leave the bracket bolted in like the video. Give a couple of toots with the air hammer. Twist pin a bit. Toot toot. etc. Mine came out in seconds.

Ok so I have a g35x sedan 2004. I just replaced my transmission from 188,000 miles to 89,000 miles. I haven’t driven it yet, but the shop thinks I should take it to Infiniti to get it flashed. I called Infiniti ahead of them and they said I shouldn’t have to. The whole transmission is replaced of course.. So should I just drive it. I haven’t even picked my car up yet. I paid for the work and everything

lifesaver, i got work in an hour and i just finished😂 thanks man

3:20 pov: local crackhead taking my tailgate once again Also thanks for the video really understood the locations compared to the other videos and very detailed

on my z the real problem is the pieces have to be small enough to fit behind the lip on the firewall.

Was this an original engine as well ? I don’t know if you stated that in the video

What you just removed is a clutch booster it is there to reduce the amount of pressure your master cylinder needs to produce to actuate the slave cylinder 😂 you just made it harder to push the clutch

My car is back firing after i replaced it do anyone know what could be the problem?

On a 1970 Chevy 454 16 screws 10 min job. KIA engineers drop the ball on this one

Yo I picked up the same o-ring kits two different times No damage to the components but for some reason those o-rings Don't seem to be working every time I pull a vacuum there's a failure what's up with that!

Great video. I like this approach, easy enough to fix in my driveway.

Good video thanks

Thanks man really helped me out

Exactly what I needed to see ty

Excellent video, very well made, concise, and to the point. I wish all CZcams repair or replace videos were made this way.

bro thank god i seen this video I was looking to get brembos but specifically 6 pistons on the front for my 350z cause they look so much better then 4

Is that air intake custom or aftermarket?

Nice job. But for the love of trucks. Please wash your engine bay. My ocd is screaming. Lol

A great video! First, you're one of the very few who actually describe and explain how to remove the plug from the sensor. I was lucky enough to not have to remove any vacuum lines. At the location of the short extension and after the swivel, I used a 3/8 to 1/2 adapter and loosened the sensor initially with my breaker bar. Once loosened, I used a regular ratchet to complete removal. To remove the filter, I found a long (3") lug screw the diameter of the filter and gently screwed it in 1/4 turn to bite into and then remove the filter. 90 minutes total, maybe less than 45 if had to do again.

So since I have a manual and don’t need the ports I just install radiator and leave the ports without nothing

Thanks for the video.helped me out. But i just want to know what the weight rating of a lowes bucket to use as a jack stand

you was able to find clips for front seats?

you can find any info about these cars on jaguar forums

Smh the classic G owner haircut 😂😂

Do you need to add oil or do an oil change when you do the gallery gaskets or it’s not necessary?

Will these work on the 300zx z32?

you made a very good video for both 1st time diy'ers & professionals. you kept with the step-by-step procedure with little or no unnecessary talk. including the factory service manual pages with torque specs and other info was a nice touch. the only step i would've added was to cover the exposed intake manifold ports during assembly as well as disassembly. also, it wouldn't hurt (and is recommended) to cover up ALL holes & passages i.e. hose connections, etc. the blue tape you used works well since it comes off easier than electrical tape or similar. also, for all the work it takes to replace the vc gaskets, i would also replace the vc's themselves in order to get new spark plug tube seals. and a new pcv valve along with installing that catch can wouldn't hurt, either. i plan to keep my car indefinitely, so i don't care to all of this work a 2nd time in a short time because of a leaking tube seal. thanx again for your very good video

Que me dices de los infinity brembo a un Nissan altima cupe ????

It's been 6 years. Did you develop cancer in your lungs from breathing this shit in?

A question, you only put 4 supports on the chassis and it doesn't fall when removing the shock absorber, I want to do it myself, that is, the arm where the front tire goes, good tutorial, greetings

Just installed their test pipes, the O2 flage bone leaking...plus the gaskets. Thanks for making this vid and affirming my leaks from Z1