Video

Casual afternoon on The Bend's drift circuit, clockwise 2 wall layout. Driving my 1.8L turbo CA18DET 180sx with 220 rwkw Its a very basic S13 build, might have a walk around video later, comment below what you want to know about the car/engine/me/driving. Music: Metrik - Ex Machina Featuring : Steven Griffin in the NC MX5 with a link fury X I wired in, set up and tuned.

Casual afternoon on The Bend's skidpan. A few months late on this upload, edited it ages ago but did have enough good footage and never finished it, Ive just cut it down super short to get it finished, hope you enjoy anyway! Driving my 1.8L turbo CA18DET 180sx with 220 rwkw Its a very basic S13 build, might have a walk around video later, comment below what you want to know about the car/engine...

Roll racing - like drag racing but from 40-50kph start. Ride along with my brother again this time in his Nissan Skyline R32 GTST . 500,000km RB30 bottom end, RB25 head, GT3576, Nistune, E85, CD009 6 speed manual, built in the home shed, tuned at The Glynde Garage to a conservative 300KW on mainline roller dyno. The limit of (reliable) power is the factory trigger and Nistune ECU, though the bi...

The night ended early when I found I broke a rear control arm Driving my 1.8L turbo CA18DET 180sx with 220 rwkw Its a very basic S13 build, might have a walk around video later, comment below what you want to know about the car/engine/me/driving. Featuring : Steven Griffin in the NC MX5 with a link fury X I wired in, set up and tuned.

A fun, no pressure drift day with some friends. Have literally done nothing to the car since last time out in it, ran flawlessly all day as it normally does. Unfortunately a few prangs, which you cant expect not to happen every now and then, luckily I didn't suffer any serious damage but Hayden wasnt so lucky in his Celica though he's turned it into a positive and is now building a car he's bee...

Day out at JDM X Park with good friends returning after a few years. First drive with the replaced bottom end, no issues there car still runs flawlessly. I spent the whole day on scrap tyres again but this time with a locked diff so no crashing into walls. Driving my 1.8L turbo CA18DET 180sx with 220 rwkw Its a very basic S13 build, might have a walk around video later, comment below what you w...

After removing my engine and stripping it down I find another CA18 engine, swap over the head, the gt2871 turbo and all the rest of the goodies before putting it on the dyno and giving it a tune up with the new motor. LONG ASS VIDEO deal with it. 1/2022 Driving my 1.8L turbo CA18DET 180sx with 220 rwkw Its a very basic S13 build, might have a walk around video later, comment below what you want...

Removal of my CA18 from my 180sx and strip it down to nothing to check for issues before potentially being built! 12/2021 Driving my 1.8L turbo CA18DET 180sx with 220 rwkw Its a very basic S13 build, might have a walk around video later, comment below what you want to know about the car/engine/me/driving.

Roll racing - like drag racing but from 40-50kph start. Ride along in my brother custom COBRA car. Carbon fibre / fiberglass body on a custom chassis fitted with a UZZ30 1UZ-FE and twin turbos, built in the home shed. Comment if there's any details you want to to cover or any questions you have.

I let Ben do drift school IN MY CAR and he CRASHES it into a barrier. This video shows the progression of Ben, who has never properly 'drifted', and by the end of the drift school morning he could drift the 'Maihan' style layout on the skidpan. If you're a fellow South Aussie and you want to try actual drifting (doing a skid leaving the lights is not drifting!), check the Drifting SA calendar f...

Roll racing - like drag racing but from 40-50kph start. I was running on wastegate pressure for a while, and when I was on full power I was missing gears and getting loads of wheel spin so I did terrible. Let me know if there's any details you want to to cover or any questions you have. 1988 Toyota Supra MA70 Turbo A ( 1/500) JZA80 2JZGTE-(non-vvt) V160 6 speed getrag Single turbo, ECU MASTERS ...

DYNO TUNE video following the issues faced in PART 1 and PART 2, completing the flex fuel tune, making full power, fine tuning for the street and testing out the rolling start, allowing boost to without accelerating. Let me know if there's any details you want to to cover or any questions you have. 1988 Toyota Supra MA70 Turbo A ( 1/500) JZA80 2JZGTE-(non-vvt) V160 6 speed getrag Single turbo, ...

DYNO TUNE video following the issues faced in PART 1 and trying again to complete the flex fuel tune. Unfortunately more issues arise on the dyno. Part 3 covers the final tune, final numbers and some driving. Let me know if there's any details you want to to cover or any questions you have. 1988 Toyota Supra MA70 Turbo A ( 1/500) JZA80 2JZGTE-(non-vvt) V160 6 speed getrag Single turbo, ECU MAST...

Quick mash of some of my better bowl runs over the weekend of The Bend 'Mini-mats' Matsuri. Music - LAMB OF GOD - HIT THE WALL Driving my 1.8L turbo CA18DET 180sx with 220 rwkw Its a very basic S13 build, might have a walk around video later, comment below what you want to know about the car/engine/me/driving. Featuring @Celi-Stang in the 302 V8 powered RA60 Toyota Celica, Ash in the RB25 power...

7/11/2020 | CA18 180SX | Mallala Drift MATSURI

26/9/2020 | CA18 180SX | Round 5 practice | The Bend

Mark's MX73 Cressida BC weld in COILOVERS INSTALL

1/8/2020 | CA18 180SX | Round 4 open track | The Bend

8/2/2020 | CA18 180SX | Mallala Drift practice

18/1/2020 | CA18 180SX | Round 1 practice | Mallala

10/11/2019 | CA18 180SX | Round 2 COMPETITION | The Bend

2JZ A70 | Issues on the dyno and BIG POWER NUMBERS

1/9/2019 | CA18 180SX | Round 1 COMPETITION | Mallala

2JZ A70 | FIRST START - FIRST DRIVE - Debrief before TUNE this weekend

29/7/2019 | CA18 180SX | JDM X Park | BIG CRASH

10/3/2019 | CA18 180SX | Round 2 COMPETITION | Mallala

18/8/2018 | CA18 180SX | Mallala Drift MATSURI

19/5/2018 | CA18 180SX | Mallala Drift MATSURI

13/5/2017 | CA18 180SX | Mallala Drift MATSURI