Video

We need a video for the 570 install!

We need a video for the sportsman 570!

Dosent explain much at all

This is no longer listed on the site

Are they brighter than stock. Thanks 😊

What are you putting the snap fasteners in? Do holes have to be drilled when upgrading a 2016 Slingshot? The video doesn’t show it very well at all and I’m very interested in making the purchase .

The screws are easy to figure out. We're do put the form.

Main lights working?

What material is the bracket made of

How does the upper light get wired for power and signal? The video doesn’t show it

Hi, does the round xenon/led lens at the bottom center also burn on low beam (when the motorcycle engine is started)? Or is this round xenon/led lens at the bottom center only for the high beam?

How are the lights switched from high beam to low beam? The 570 full-size does not have dual beam factory lights. In my opinion, the factory lights are unusable. Is there a toggle switch that has to be installed in order to change from low beam to high beam?

Why don’t you guys make these for 2024 sportsman 850 touring?

The supplied bolt that goes on top does not fit. I had to go buy a 3”bolt to go all the way through with nut on back side in order to get this to work. Should look at modifying the kit.

where did u get the rear trailering arm covers?

What about for the F3?

Per Sportsman 1000 S?

The engine is in the back. How does that help heat dissipation?

i have 2015 and 2017 and they said right side

Do we have to buy the black outer housing or we can use the original one ?

Does the original one fit on these headlights or we have to buy the covers too ? Thanks :)

This video was not helpful. The camera work is terrible and the installer is going too fast.

What are the foams that come with it for?

Your video is showing the pioneer 1000, not the 700. Ive got a 700 and its impossible to find a tablet mount

Can you still install a passenger backrest with the tail bag off?

you guys should make a version with a built in fan pulling cool air in from the outside at slower speeds. i feel like that would sell like crazy. especially to the guys like me with 2024+ xp1000s that are insanely hot inside

Does this block winch location?

The red lockdown clip will screw up loading heavy stuff that you have to slide into the tray. I do like the 2" extenders though, great idea.

What extra device do i need for turning signals?

Did you just mounted it upside?? Lo😂.

If you buy these and they don't come on when plugged into the keyed power source, check the pos/neg wire locations in the 2 wire plug. I have a 2024 and found that the positive/negative wires were reversed compared to the factory plug. Grabbed a small pick and de-pinned the plug that came with the fang lights. Swapped placement of the wires and it worked like a charm. If you don't know how to de-pin wiring plugs, I recommend watching a video on it. Super simple once you know what you are looking for in the plug. Takes a little pressure in the right spot and the wires can be removed from the plug. They snap back into place when inserting them back in.

I did all the same steps on the video but I can’t get the white light on

I'm having a terrible time adjusting the height of my brake pedal with these installed. Do you just have to uninstall it to be able to change the pedal adjustment or am I missing something?

I assume they’re pretty easy? The factory sent two to be installed at the dealer but the dealer received two left hand guards… so I am going to have to install the right one when it comes but have my bike delivered tomm. They said the brackets are on so I just have to screw the right one in Is it that easy?

What size drill bit did you use to make hole bigger?

Did not go together as easy as this! The clamps were very hard to get the bolts in and some didnt meet the holes anywhere close. Had to drill new holes.

But why not use the bus bar?

Any eta when these will be available on Amazon? I need one for my X2 1000.

I just received my windshield for my 2022 General XP, and same thing,, There's about a 1/4 - 1/2 inch gap on 1 side, after I connect the other. I can't get it to clamp down after several attempts.

do you have the instal video

Can this be used with the hood scoop light as plug and play or does the power to the hood light need to be disconnected?

Can you get blinking functionality out of these with the xtc street legal kit?

Do the replacement running lights/turn signals only work with the ryco kit? Id like to make them work with the xtc kit if possible. Thanks

I need to see some reviews on these! I want to buy them so bad but I haven’t seen any reviews. I really want them too

Is the Can-am already pre-wired for the grill? Was it connected to a dud retainer?

How did these boxes sound with the sub in it

Will it make the back light blink as well?

Seperate switch, or is it on when the low beams are on, or only the high beams ??

Do you plan on offering a liner as well? A little more coverage up the sides would be perfect.

will these brackets work with a factory Honda roof?