- 37
- 24 500
Hillbilly Handworks
United States
Registrace 2. 04. 2024
to educate and entertain viewers about the outdoors, firewood, and DIY projects
Husqvarna 392xp project, finishing reassembly PART 2
part 2 of reassembling this project saw. there will be a few adjustments being made off camera but other than that I will eventually post a first start up video.
thanks for watching
please subscribe
thanks for watching
please subscribe
zhlédnutí: 194
Video
Husqvarna 392xp project, finishing up and reassembling PART 1
zhlédnutí 182Před 21 dnem
I am going over everything I did off camera and started to put it back together to finally finish this crazy build. thanks for watching please subscribe
cutting HAZARDOUS trees, EPIC FAIL!!!
zhlédnutí 408Před 21 dnem
on a property cutting trees near a house, equipment, and wires. only 2 of the 10 were able to be filmed. the rest were so bad both of us were working on them cutting and pulling them over. thanks for watching please subscribe
falling hazardous white oak
zhlédnutí 4,7KPřed 28 dny
falling a hazardous white oak with ported Stihl 461 thanks for watching please subscribe
Husqvarna 392xp project, update on muffler mod and plans for the air filter
zhlédnutí 56Před 28 dny
finished the muffler and getting very close to putting this beast together. a little more work needs to be done which I will post in the near future. thanks for watching please subscribe
Husqvarna 392xp project, grinding the transfers
zhlédnutí 79Před 28 dny
now starting to Port the cylinder as we grind out the transfers, showing some "proper" technique to not screw it up. next video will be a update on the porting and muffler mods. thanks for watching please subscribe
Husqvarna 392xp project, UPDATE on fitment of cylinder and piston
zhlédnutí 156Před měsícem
quick update on the 392xp project, the cylinder and piston are completely fitted and now we are starting to take steps into grinding out transfers and porting. thanks for watching please subscribe
Husqvarna 392xp project, fitting the cylinder
zhlédnutí 64Před měsícem
now we are fitting the cylinder to the case so it will bolt up and fit just right. I go through most of the process in this video. thanks for watching please subscribe
Husqvarna 392xp, making a plan
zhlédnutí 73Před měsícem
now that the cylinder is off, I am planning out how I will be fitting the cylinder and piston to the case and much more. thanks for watching please subscribe
Husqvarna 392xp project saw
zhlédnutí 247Před měsícem
this is an introduction to a new project saw I am doing. it is a clone 372 with a Husqvarna 390xp big bore cylinder assembly. thanks for watching please subscribe
disassembling, porting, and assembling clone 046 PART 3
zhlédnutí 25Před měsícem
finishing the reassembly and fixing on testing it out in the future thanks for watching please subscribe
disassembling, porting, and reassembling clone 046 PART 2
zhlédnutí 37Před měsícem
part 2 of the holzforma g466 series, starting to reassemble the saw thanks for watching please subscribe
disassembling, porting, and reassembling 046 clone PART 1
zhlédnutí 219Před měsícem
porting a holzforma g466, doing kinda like a series for this build so look out for part 2 thanks for watching please subscribe
DIY easy mower blade sharpening
zhlédnutí 93Před 2 měsíci
easy and efficient way to sharpen your lawn mower blades to make them very sharp in under 10 minutes please subscribe thanks for watching
holzforma g466 pull rope and handle replacement
zhlédnutí 8Před 3 měsíci
holzforma g466 pull rope and handle replacement
ported Stihl 462 vs ported Husqvarna 372
zhlédnutí 54Před 3 měsíci
ported Stihl 462 vs ported Husqvarna 372
How long before start up been waiting for a video for 3wks since this video?
😮😮😮😮
👍👍🙏🙏
I can’t believe it 😮
Hyway caber piston rings yes sir
Nice job. Tricky looking drop. Stay safe
I regret watching
Ggggggggrrrrrrrrrrrrrrr
😐
How did you come up with 92cc? A 390 is only 88cc. a 55mm bore on a 372 crank (36mm) is only 85.5cc.
It is a 390 big bore, so it is 57mm and when I did the calculations with 57mm bore and 36mm stroke it was a bit over 91 so I'm calling it 92
Buddy you can take a sentence and turn it into a paragraph just get it done!!
Did you compression test the saw? Reason I ask is if it's like mine compression is fine. My issue is timing. Flywheel is too far advanced causing snaped the ropes and a sore wrist. Better rope and a D hand too but would have been cheaper to retard the timing a couple degrees.
I don't have a compression tester handy but with the modifications I did it helped it out
just to let you know your video is really broken lots of gray screen and skipping when there is picture
czcams.com/video/ib73ayR9EAM/video.htmlsi=gCMCjDLzeEBYiC-A My Channel ...Firewood. 😊
Wooow Power Saw... Nice Video. Greetings from Germany Peter Husqvarna-Pit 😎
Nice Chainsaws Greetings from Germany Peter.
Let her eat David!
Fuck yeah
Fuck yeah
😊 Promo_SM
Well, can they do firewood???? Which saw won ?????
Both can do firewood, the 440 won
Them oldies was stout units
Good Info !!!
I need that wood to make syrup !!!!
Keep the posts coming !!! Saw baby saw !
Good Job !!!
I love you David