Video

Done incorrectly

at czcams.com/video/ZIsvDB65O20/video.htmlsi=JqFn2irkoDi9pkVq&t=1230 , you rotated the camshaft mark to get it align with the new timing belt, isnt that a no no?

Awesome video! Just a question, before installing head gasket and after you applied silicon. What kind did you use? Thanks in advance.

It’s coming from the Abs unit, the brake switches was the cause of the no start I got another video where I got it to run..but been waiting on my customer to approve the abs unit to also fix the buzzing noise 5:07

Where are you located????

Ever figure out the issue with this? Im having same problem

Having this issue right now but with both of my rear lights, my recerse and brake lights work but the rear light just doesn’t light up unless I press on the brake

Thank you so much for sharing!!

Great video! Im replacing my connecting rods since 2 bent 😣 any suggestions? I just have no idea how the timing will work!

Excellent, show each critical steps thank you very much

😂😂😂😂

Good work 💯 thank

thank you for the information. i will use this method

😂😂😂

What are those seals called that go in between the ladder frame and block

Was the cover aluminum or plastic ? 41:26

I was wondering if you took the other motor mount on the top and left the bottom but loosened the bolt would you be able to slide the engine just a bit to the right so the timing cover can go back on a little easy? I'm going to be needing to do this job just waiting till i my oil change is due so i can change the oil since I'm going to be dumping it out for the job. Thanks for the video great info

Tellem tellem

❤❤❤❤

Time for a beer for you. That job gave me anxiety just watching😂

I have a 1.6 hundyia tusson turbo 1000 hundred miles

Have exactly the same issue with my Juke 😢 Suspected it was the chain, thanks to you now I'm certain 😢 Thanks for the video and tips ❤

Did this engine actually run after this rebuild because I'm getting ready to start building my engine and I just couldn't find a build video or manual on putting the g4fj engine back together after tearing it down

Do you have to order the crankshaft from KIA? Ive seen a lot of cheap crankshafts for sale in a rebuild kit.

how was matinence on this?

How did the swap turnout?

How much does that repair cost? My engine is rattling passenger side …

How is the pin conecting the piston and rod held together?

Hey.

Eji, thanks for the great video. I have seen many videos of kia engine being taken apart, but not rebuild. 👍

I have a kia cerato 2009 it did over heating, after surfacing the cylinder head it started burning oil. My mechanic think it's best I get a new engine. Please what can I do as the engine runs fine but burns 1 litre under 300km.

Good job man going through everything so people can see, good content my friend.

By their accents you shall know them, love it

Nice job. It's nice to see the final stages of the headliner replacement.

Is the tensioner is automatic adjust? No need to adjust ? Btw thanks for your video

Thanks for timing cover info!

after roatating engine how did u find timing mark is line up?

bro after doing everything as u said when i roate engline 360 degree do mark on camsaft and color on chain have to matchg after 360 degree roattion or it dont have to match??

Hi nice work, How many miles on the engine?

As an auto painter this is cringey. Paint from top to bottom, use lighter coats, spot sand and tack in between coats, do a full coat on the whole panel before you decide to do another coat in a section, and that’s just from watching this for 5 minutes lol I wish the vehicles I painted were this simple yet that paint job came out dirty as hell the camera didn’t even hide it lmao

I am undertaking this repair tomorrow, thank you for all the tips.

Great video man. You gained a subscriber.

My fellow naija. I sight you

do u have to remove bottom gear to put timing chain or it just go around and u just tentioner will tight it just like do with bycle

What an amazing vehicle

Video helped sooo much. Thank you

I like your video I got the same problem with😢😢

Great video Sir! Did you have to hone the cylinder walls on this particular engine or is not required? Thank you!

I was completely lost. I appreciate this video. Thank you

Where are you watching from ..?