Video

Sir Pm nyo lng po Modular repaird dept sa facebook..

@@calebdizon. it means the problem is in the active speaker.. replace TDA I'C . It is mounted in the heatsink.. also look for bulging ecap.. replace them also.

@@FixYahTv Do you have a video of this kuya? I was trying to do it but I got confused. Thank you po!

@@Djdangskie64 thank you so much friend..

@@khaielofficial please contact Modular Dusplay Inc.

@@omnicerberus6596 saan nyo nabili unit ninyo po?

@@FixYahTv sa music world baguio po sir

@@omnicerberus6596 ano naging sir ng unit nyo sir?

@@omnicerberus6596 dalhin nyo po sa music world baguio sir.. ask for warranty.. alam ko kasi 6 yrs warranty yan.. ipakita nyo lng resebo nyo.. then dadalhin yan sa supplier.. dapat naka attach yong copy ng resebo nyo.. then the supplier ipapagawa nila yan sa amin..

I think the problem with your unit is the main output IC. The one that is mounted to the heatsink. Try also to replacing bulging capacitor around the IC..

Just click CC (caption) it has a english translation.

@@producerdiaz1806 i have another video similar to the problem you are having.. check it out on my channel.

@@FixYahTv what's the link if the video or title? I wanna make sure I'm watching the right one.

@@chetvoxx about sa 16.4 2 na ka hang ba ang GR nya? If so subukan mo muna ifactory reset using old version of macbook dun lng kasi sya gumagana. Di kasi sya narerecognized ng mga new version.. then iupdate mo yong firmware sa pinakamababa hanggang pataas.. dapat walang laktaw. Pag di parin umobra try to replace the 3 pcs 5volts regulator sa DSP.. if wala prin it means DSP is defective na.. about nman sa 24.4.2 nman.. its a Pre-amp issue.. may SMD resistor dyan n 100 ohms malapit sa potentiometer baka sunog na kaya walang signal napumapasok .. pwd rin yong amp ic nya ang sira sa ch.5 ang may problem.

Salamat ng marami. Hindi ako marunong ng electronics pero susubukan ko. Unahin muna yung 16.4.2. Binuksan ni misis just to look inside. Do not see any leak sa capacitor. Yung pang update ng firmware siguru muna ang gagawin ko. Then factory reset ko. Thank you

Experienced the same the day before Yesterday in central Europe, so I can feel your pain ) I was searching for repairing instructions, but then, watching this I decided to save my nerves and time. This is obviously a Design flop of PreSonus. I also Googled a bit and yes, we are not alone. PreSonus rolled out and advertized the 2nd Gen, where they put a glas fuse in the box. So, this might seem as rework, but they basically mean by that, that the problem may pop up again (and this is halfway a temporary solution). Not good. One might want to look for something else.

@@cycobeez try to modify your board by replacing the 3 pcs 5volts regulator with 7805 regulator..

@@FixYahTv thanks man. can you make a video of it? a lot of people will be happy

Just contact Modular Display Inc po sir.

@@pepzisko13 just contact modular display inc..

RS components.

@@FixYahTv Thanks. Raises one question. No catalogues, show, the switch back image with 4 pins. Is this the switch type? DP ON - OFF Cat no. R13 244A AAA docs.rs-online.com/af05/0900766b808a97c8.pdf

@@user-kv5oi3vo7b anong unit sir?

Presonus Studiolive 16.0.2 po sir

​@@FixYahTvpwde po ba makahingi messenger sir, para ma send ko po video sa presonus ko sir para makita mo po yung deffect nya

@@user-kv5oi3vo7b ano sir messenger nyo ako magpm sa inyo.

@@FixYahTv Shable Jayn po sir

You should also check the LF driver ..

@@FixYahTv sí, caray. Está destruido el imán del woofer :'(. Sabes si ¿presonus vende refacciones?

Modular Repaird Dept. dito nlng po kayo magmsg sir.

You have to replace the volume potentiometer if the volume knob is scratchy.. the part no# of the potentiometer.. RK097G 10K 6PIN variable Resistor rotary carbon film taper Potentiometer.

The problem when the volume causes crackling is corrosion over time. Wear and tear from constant use.. to fix it is to replace the volume potentiometer..

Modular Display Inc po..

Pm nyo po ako sa facebook.. Modular Repair Dept.

Thanks you

Check for speaker bka nasunog pag ok mman.. replace TDA ic.. yong nkakabit sa Heatsink if present ang power..

You can order it on RS components online.

I'm glad my video was helpful😊

its 4Pin 6A 125/220V AC DPST ON-OFF Rocker switch Snap-in.

@@FixYahTv is it ok, if it's 250v. Not finding 125/220v?

Yes sir.. its ok..👍🏻

Hello. Thanks to your video, I found the cause. Thank you. Can I use spst instead of dpst?​@@FixYahTv

Use only DPST switch for safety.

Glad it helped

Try to watch my other video😁

Check my other video 😉

Misuse it is 😢😭

You can only get it on presonus authorize service center..

Glad to be of help.. 😁👍🏻

I hope you also support my channel.. thank you😁✌

Check mo sir mga connection, minsan lumuluwag dahil sa vibration. Check for bulging capacitor.. check mo din sir yong TDA ic bka nagooverheat.. lagyan mo ng bagong thermal grease. Check mo rin yong speaker if good pa bk mababa na sa 4 ohms. For now yan muna sir ang mga dapat mo icheck.. sana makatulong..👍🏻

What seems to be the problem?

@@FixYahTv similar to this actually, my active speaker, left side was not giving loud output like passive speaker and then yesterday it just stopped giving output. To make sure it was isolated to left speaker I removed the red/black connector wires and played audio only in left, It was playing audio with very small soft volume even with volume knob turned to max. If it’s anything similar to the problem in this speaker I suspect it must be a blown capacitor, sir

Try to replace bulging capacitors. Sometimes capacitor leaks and causing weak and sometimes buzzing noise.

Novaliches QC po sir..

@@FixYahTvthanks! Texted the number. You dont fix the 3.5 daw, palit daw. Thanks na lang.

Saan nyo sir nabili unit ninyo?

@@FixYahTv I brought it with me from the US. but that should not matter. I have an MR4 on order which based on reviews is better than the Eris =.

I see.. kaya po pala di nila tinanggap yong unit ninyo kasi di nabili dito sa pinas.. ang tinatanggap lng po kasi nila is yong binili sa mismong supplier dito sa pinas. Pasensya na po pero i hope my video help you fix your unit po..

You can order online.. T 3.5A.

@@FixYahTvthank you so much keep up the good work

If your unit is under warranty you should send it to your supplier but if itis not. Try to replace bulging capacitor near the TDA ic.

Did it work?

What would of been great if you had the whole video unedited. for me to watch. As i haven't done this kind of thing before. do you still have the whole video?

Sorry man.. i dont have it anymore.. just replace all the bulging capacitor and thats should fixed the problem.

@FixYahTv no worries man. Just wanted to see what you used. I noticed you put some brown liquid around the capacitors. What is that? Also, you used something to glue the foam back on. Things like that would be really helpful to know.

You can use RTV silicone adhesive.

@@FixYahTv thanks man

Thet are called SL 1642 LCD 192x64. But you can order it on your Presonus supplier only.

​@@FixYahTv thank you